2014 JEEP WRANGLER Owners Manual

Front Panel(s) Removal
NOTE: Left panel must be removed before removing
right panel.
1. Fold down the sun visor, and move it to the side.
2. Turn the rear fasteners (knobs) (located on the over-head speaker bar assembly) counterclockwise until
they can be removed.
3. Turn the center L-shaped locks (two) from the centerof the roof panel.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207

4. Turn the rear L-shaped lock (located above the shoul-der belt anchorage). 5. Unlatch the header panel latch located at the top of the
windshield.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

6. Remove the left-hand panel.
To remove the right panel, follow the steps above
except for Step 3.
Freedom Top™ Storage Bag
Vehicles equipped with a Freedom Top™ Modular Hard
Top, come with a Freedom Top™ storage bag that allows
you to store your Freedom Top™ panels. The storage bag
contains two compartments and fits behind the rear seat.
Lay the Freedom bag down so the loops and hooks are
facing downward. Unzip the bag and fold back the outer
flap. Release the Velcro® on the black panel divider and
fold it back.
NOTE:Ensure the front Freedom Top™ panel latch is
closed prior to inserting the panel into the Freedom bag.
Insert the right side Freedom panel into the bag with the
latches facing downward.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209

Unfold the black panel divider (ensure the divider is
laying flat). Secure the Velcro®, located at the center of
the divider.Insert the left-side Freedom panel into the bag with the
latches facing upward.
NOTE:
Ensure the front Freedom panel latch is closed
prior to inserting the panel into the bag.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Unfold the outer flap and zip the Freedom bag closed. Install the seat attachment strap (at the top of the bag)through the loops.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211

Lift the Freedom bag into the vehicle with the hooks and
straps facing the back of the rear seat. Attach the clips at
the bottom of the bag to the child restraint anchorages,
located at the base of the rear seat.Wrap the upper strap around the rear head restraints and
loop the strap through the buckle. Pull on the strap to
tighten the Freedom bag securely against the rear seat.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Front Panel(s) Installation
NOTE:Set the panels on the windshield frame so that
there is no overhang. Also, make sure that the panels are
sitting flush with the body.
1. Install the right panel first, then the left panel. 2. Reinstall the panel(s) using the same steps for removal
in reverse order.
Front Panel(s) Installation With Rear Hard Top
Removed
1. Turn the left and right panels over and move thespacer block (located on the rear of the panel) upward
90 degrees.3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213

NOTE:The front panel(s) must be positioned properly
to ensure sealing. Set the panels on the windshield frame
so that there is no overhang. Also, make sure that the
panels are sitting flush with the body.
2. Install the right panel first, then the left panel. 3. Reinstall the panel(s) using the same steps for removal
in reverse order.
Rear Hard Top Removal
1. Remove both front panels. Refer to “Front Panel(s)Removal” in this section.
2. Open both doors.
3. Remove the two Torx® head screws that secure the hard top at the B-pillar (near the top of the door) using
a #40 Torx® head driver (Four–Door Only).
4. Remove the six Torx® head screws that secure the hard top to the vehicle (along the interior bodyside)
using a #40 Torx® head driver.
5. Open the swing gate all the way to ensure clearance of the rear window glass. Lift the rear window glass.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE