2014 INFINITI QX80 Owners Manual

5-36Starting and driving
SSD0957
Dynamic driver assistance switch
BLIND SPOT INTERVENTIONTMSYS-
TEM OPERATION
If the radar sensors detect vehicles in the
detection zone, the Blind spot warning
indicator light located inside the outside
mirrors illuminates. If your vehicle is
approaching a lane marker, the Blind spot
warning indicator light flashes and an
audible warning will sound three times.
Then the system applies the brakes on one
side of the vehicle for a short period of
time to help return the vehicle back to the
center of the lane. Blind Spot Interven-
tion
TMoperates regardless of turn signal usage.
NOTE:
.
Warning and brake control will only be
activated if the Blind spot warning
indicator light is already illuminated
when your vehicle approaches a lane
marker. If another vehicle comes into
the detection zone after your vehicle
has crossed a lane marker, no warning
or brake control will be activated. (See
“BSW/Blind Spot Intervention
TMdriv-
ing situations” later in this section.)
. The Blind Spot Intervention
TMsystem is
typically activated earlier than the
Lane Departure Prevention (LDP) sys-
tem when your vehicle is approaching
a lane marker.
The Blind Spot Intervention
TMsystem turns
on when the dynamic driver assistance
switch on the steering wheel is pushed
when the “Blind Spot Intervention” is
enabled in the settings menu on the center
display. The Blind Spot Intervention
TMON
indicator light (green) on the instrument
panel illuminates when the Blind Spot
Intervention
TMsystem is turned on.
The Blind Spot InterventionTMsystem
provides an audible warning and flashes the indicator light when Blind Spot Inter-
vention
TMis activated even if the BSW
system is off.

SSD0959
SSD1102
How to enable/disable the Blind
Spot InterventionTMsystem using
the setting menu
Perform the following steps to enable or
disable the Blind Spot InterventionTM
system.
1. Push the SETTING
*1button and high-
light the “Driver Assistance” key on the
display using the INFINITI controller.
Then push the ENTER
*2button.
2. Highlight the “Dynamic Assistance Set-
tings” key, and push the ENTER
*2
button.SSD1002
3. Highlight the “Blind Spot Intervention”
key, select ON (enabled) or OFF (dis-
abled) and push the ENTER
*2button.
For the LDP and DCA systems, see “Lane
Departure Prevention (LDP) system” earlier
in this section and “Distance Control Assist
(DCA) system” later in this section.
Starting and driving5-37

5-38Starting and driving
Precautions on BSW/Blind Spot
InterventionTMsystem
WARNING
.Do not use the Blind Spot InterventionTM
system under the following conditions
because the system may not function
properly.
—During bad weather (for example,
rain, fog, snow, wind, etc.)
—When driving on slippery roads,such as on ice or snow, etc.
—When driving on winding or uneven
roads.
—When there is a lane closure due toroad repairs.
—When driving in a makeshift lane.
—When driving on roads where thelane width is too narrow.
—When driving with a tire that is notwithin normal tire conditions (for
example, tire wear, low tire pressure,
installation of spare tire, tire chains,
non-standard wheels).
—When the vehicle is equipped withnon-original brake parts or suspen-
sion parts.
. Do not use the BSW or Blind Spot
Intervention
TMsystems when towing a
trailer.
. Excessive noise (for example, audio
system volume, open vehicle window)
will interfere with the chime sound, and
it may not be heard.
. The radar sensors may not be able to
detect and activate Blind Spot Interven-
tion
TM/BSW when certain objects are
present such as:
—Pedestrians, bicycles, animals
—Several types of vehicles such as motorcycles
—Oncoming vehicles
—Vehicles remaining in the detectionzone when you accelerate from a
stop
(See “BSW/Blind Spot Intervention
TM
driving situations” later in this sec-
tion)
—A vehicle merging into an adjacent lane at a speed approximately the same as your vehicle
(See
“BSW/Blind Spot Intervention
TM
driving situations” later in this sec-
tion)
—A vehicle approaching rapidly from behind.
(See “BSW/Blind Spot Intervention
TM
driving situations” later in this sec-
tion)
—A vehicle which your vehicle over-
takes rapidly.
(See “BSW/Blind Spot Intervention
TM
driving situations” later in this sec-
tion)
. Severe weather or road spray conditions
may reduce the ability of the radar to
detect other vehicles.
. The radar sensors detection zone is
designed based on a standard lane
width. When driving in a wider lane,
the radar sensors may not detect vehi-
cles in an adjacent lane. When driving in
a narrow lane, the radar sensors may
detect vehicles driving two lanes away.
. The radar sensors are designed to ignore
most stationary objects, however ob-
jects such as guardrails, walls, foliage

and parked vehicles may occasionally be
detected. This is a normal operating
condition.
. The camera may not detect lane markers
in the following situations and the Blind
Spot Intervention
TMsystem may not
operate properly.
—On roads where there are multiple parallel lane markers; lane markers
that are faded or not painted clearly;
yellow painted lane markers; non-
standard lane markers; lane markers
covered with water, dirt, snow, etc.
—On roads where discontinued lane
markers are still detectable.
—On roads where there are sharpcurves.
—On roads where there are sharply
contrasting objects, such as sha-
dows, snow, water, wheel ruts,
seams or lines remaining after road
repairs.
—On roads where the traveling lanemerges or separates.
—When the vehicle’s traveling direc-tion does not align with the lane
markers.
—When traveling close to the vehiclein front of you, which obstructs the
lane camera unit detection range.
—When rain, snow or dirt adheres tothe windshield in front of a lane
camera unit.
—When the headlights are not brightdue to dirt on the lens or if aiming is
not adjusted properly.
—When strong light enters a lane
camera unit. (For example, light
directly shines on the front of the
vehicle at sunrise or sunset.)
—When a sudden change in bright-ness occurs. (For example, when the
vehicle enters or exits a tunnel or
under a bridge.)
SSD1026
BSW/BLIND SPOT INTERVENTIONTM
DRIVING SITUATIONS
Another vehicle approaching from
behind
The Blind spot warning indicator light
illuminates if a vehicle enters the detection
zone from behind in an adjacent lane.
However, if the overtaking vehicle is
traveling much faster than your vehicle,
the indicator light may not illuminate
before the detected vehicle is beside your
vehicle. Always use the side and rear
mirrors and turn and look in the direction
your vehicle will move to ensure it is safe
Starting and driving5-39

5-40Starting and driving
to change lanes.
SSD1031
If the driver activates the turn signal, then
the Blind spot warning indicator light
flashes and a chime will sound twice.
NOTE:
If the driver activates the turn signal
before a vehicle enters the detection zone,
the Blind spot warning indicator light will
flash but no chime will sound when the
other vehicle is detected.
SSD1044
If the Blind Spot InterventionTMsystem is
on and your vehicle is approaching a lane
marker, the Blind spot warning indicator
light flashes and a chime will sound three
times. Then the Blind Spot Intervention
TM
system slightly applies the brakes on one
side to help return the vehicle back to the
center of the driving lane.

SSD1032
NOTE:
If you accelerate from a stop with a vehicle
in the detection zone, the other vehicle
may not be detected.
SSD1033
Overtaking other vehicles
The Blind spot warning indicator light
illuminates if you overtake a vehicle and
that vehicle stays in the detection zone for
approximately 3 seconds.
The radar sensors may not detect slower
moving vehicles if they are passed quickly.
SSD1034
If the driver activates the turn signal while
another vehicle is in the detection zone,
then the Blind spot warning indicator light
flashes and a chime will sound twice.
Starting and driving5-41

5-42Starting and driving
SSD1093
If the Blind Spot InterventionTMsystem is
on and your vehicle approaches a lane
marker while another vehicle is in the
detection zone, the Blind spot warning
indicator light flashes and a chime will
sound three times. Then, the Blind Spot
Intervention
TMsystem slightly applies the
brakes on one side to help return the
vehicle back to the center of the driving
lane.
SSD1036
NOTE:
When overtaking several vehicles in a row,
the vehicles after the first vehicle may not
be detected if they are traveling close
together.

SSD1037
Entering from the side
The Blind spot warning indicator light
illuminates if a vehicle enters the detection
zone from either side.
NOTE:
The radar sensors may not detect a vehicle
which is traveling at about the same speed
as your vehicle when it enters the detec-
tion zone.
SSD1038
If the driver activates the turn signal, then
the Blind spot warning indicator light
flashes and a chime will sound twice.
NOTE:
If the driver activates the turn signal
before a vehicle enters the detection zone,
the Blind spot warning indicator light will
flash but no chime will sound when
another vehicle is detected.
SSD1094
If the Blind Spot InterventionTMsystem is
on and your vehicle approaches the lane
marker while another vehicle is in the
detection zone, the Blind spot warning
indicator light flashes and a chime will
sound three times. Then, the Blind Spot
Intervention
TMsystem slightly applies the
brakes on one side to help return the
vehicle back to the center of the driving
lane.
Starting and driving5-43