2014 INFINITI Q50 HYBRID Owner's Manual

5-48Starting and driving
radar obstruction”warning message ap-
pears even after the BSI system is turned
on again, stop the vehicle in a safe location
and turn the INFINITI Direct Response
Hybrid
®System off. Check for and remove
objects obscuring the radar sensors on the
rear bumper, and restart the hybrid sys-
tem.
Condition C:
If the vehicle is parked in direct sunlight
under high temperature conditions (over
approximately 1048F (408C)) and then the
BSI system is turned on, the BSI system
may be deactivated automatically. The
“high cabin temperature” warning mes-
sage will appear in the vehicle information
display.
Action to take:
When the above conditions no longer exist,
push the dynamic driver assistance switch
again to turn the BSI system back on.
BSW/BSI malfunction
When the BSW/BSI systems malfunction,
they will be turned off automatically, a
beep will sound, the and the system
“malfunction” warning message with the
driver assist system blind spot indicator
(orange) will appear in the vehicle informa- tion display.
Action to take:
Stop the vehicle in a safe location, turn the
hybrid system off and restart the hybrid
system.
If the system malfunction warning message
with the driver assist system blind spot
indicator (orange) continues to be dis-
played, have the BSW/BSI systems
checked by an INFINITI retailer.
BACK-UP COLLISION INTERVENTION
(BCI) SYSTEM
The Back-up Collision Intervention (BCI)
system can help alert the driver of
approaching vehicles or rear objects when
the driver is backing out of a parking
space.
When the shift lever is in the R (Reverse)
position and the vehicle speed is less than
approximately 5 MPH (8 km/h), the BCI
system operates.
JVS0233X
JVS0173X

JVS0234X
The BCI system uses radar sensors*1
installed on both sides near the rear
bumper to detect an approaching vehicle
and sonar sensors
*2to detect objects in
the rear.
The radar sensors
*1detect the approach-
ing vehicle from up to approximately 49 ft
(15 m) away. The sonar sensors
*2detect
a rear obstacle at up to approximately 4.9
ft (1.5 m) from the bumper. Refer to the
illustration for approximate zone coverage
areas
*3.
If the radar detects a vehicle approaching
from the side or the sonar detects close
objects in the rear, the system gives visual and audible warnings, and then applies
the brake for a moment when the vehicle is
moving backwards. After the automatic
brake application, the driver must depress
the brake pedal to maintain brake pres-
sure. If the driver’s foot is on the accel-
erator pedal, the system pushes the
accelerator upward before applying the
brake. If you continue to press the accel-
erator, the system will not engage the
brake.
WARNING
.
The BCI system is not a replacement for
proper driving procedure and is not
designed to prevent contact with vehi-
cles or objects. When backing out of
parking space, always use the inside
and outside rearview mirrors and turn
and look in the direction you will move.
Never rely solely on the BCI system.
. There is a limitation to the detection
capability of the radar and the sonar.
Using the BCI system under some road,
ground, lane marker, traffic or weather
conditions could lead to improper sys-
tem operation. Always rely on your own operation to avoid accidents.
Starting and driving5-49

5-50Starting and driving
JVS0304X
Upper display
BCI system operation
When the shift lever is placed in the R
(Reverse) position, the indicator on the BCI
system key
*1illuminates on the upper
display.
SSD1028
Side indicator light
JVS0307X
Upper display The BCI system operates by detecting the
vehicles and/or objects using either the
radar or sonar sensors.
An approaching vehicle from the side:
If the radar detects an approaching vehicle
from the side, the system chimes a sound
(single beep), the side indicator light on
the side the vehicle approaching from
flashes and a yellow rectangular frame
*A
appears on the upper display.

JVS0172X
JVS0173X
NOTE:
.In the case of several vehicles ap-
proaching in a row or in the opposite
direction, a chime may not be issued to
the BCI system after the first vehicle
passes the sensors.
. When the sonar sounds a tone, the BCI
system does not chime a sound (single
beep).
If the detected vehicle approaches closer
and your vehicle is backing up toward the
detected vehicle, the system chimes a
sound (three times) and a red rectangular
frame
*Aappears on the upper display.
The system applies the brake for a
moment. After the automatic brake appli-
cation, the driver must depress the brake
pedal to maintain brake pressure.
If the driver’s foot is on the accelerator
pedal, the system pushes the accelerator
pedal upward before applying the brake. If
you continue to press the accelerator
pedal, the system will not engage the
brake.
A close object behind the vehicle:
If the sonar detects a close object behind
the vehicle when your vehicle is backing
up, the system chimes a sound (three times) and red rectangular frame
*A
appears on the upper display. The system
applies the brake for a moment. After the
automatic brake application, the driver
must depress the brake pedal to maintain
brake pressure.
If the driver’s foot is on the accelerator
pedal, the system pushes the accelerator
pedal upward before applying the brake. If
you continue to press the accelerator
pedal, the system will not engage the
brake.
NOTE:
The BCI system does not operate if the
object is very close to the bumper.
Starting and driving5-51

5-52Starting and driving
JVS0304X
Upper display
The BCI system is turned off temporarily by
touching the BCI system key
*1on the
upper display. The indicator on the BCI ON
key turns off.
When the shift lever is placed in the R
(Reverse) position again, the BCI system is
turned on.
The BCI system automatically turns on
every time the hybrid system is started.
JVS0246X
Turning the BCI system ON/OFF
Perform the following steps to turning the
BCI system on or off.
1. Push the MENU button
*1and touch
[Settings] on the lower display.
2. Touch [Camera/Sonar].
3. Touch [Back-up Collision Intervention] to turn the system ON/OFF.
When the BCI system is turned off by
touching [Back-up Collision Intervention],
the BCI system does not turn on auto-
matically by the following operations:
. When the shift lever is placed in the R (Reverse) position
. When the hybrid system is restarted

JVS0170X
Precautions on BCI system
WARNING
.The radar sensors may not be able to
detect certain objects such as:
—Pedestrians, bicycles or animals
—A vehicle that is passing at speeds
greater than approximately 15 MPH
(24 km/h)
. The radar sensors may not detect approaching vehicles in certain situa-
tions.
—When the vehicle parked next to you
obstructs the beam of the radar
sensor.
—When the vehicle is parked in an
angled parking space.
—When the vehicle is parked oninclined ground.
—When a vehicle turns into or backs
up into your vehicle’s aisle.
—When the angle formed by yourvehicle and approaching vehicle is
small.
. Severe weather or road spray conditions
may reduce the ability of the radar to
detect other vehicles.
. The sonar sensor may not detect:
—Small or moving objects
—Wedge-shaped objects
—Object close to the bumper (less
than approximately 1 ft (30 cm))
—Thin objects such as rope, wire andchain, etc.
Starting and driving5-53

5-54Starting and driving
.The brake engagement by the BCI
system is not as effective on a slope as
it is on flat ground. When on a steep
slope the system may not function
properly.
. Do not use the BCI systems under the
following conditions because the system
may not function properly.
—When driving with a tire that is not
within normal tire conditions (for
example, tire wear, low tire pressure,
installation of tire chains, non-stan-
dard wheels).
—When the vehicle is equipped with
non-original brake parts or suspen-
sion parts.
. Excessive noise (for example, audio
system volume, open vehicle window)
will interfere with the chime sound, and
it may not be heard.
BCI temporarily not available
When the following message appears in
the vehicle information display, a chime
will sound and the BCI system will be
turned off automatically. .
“Unavailable High Accelerator Temp.”:
When the accelerator pedal actuator
detects that the internal motor tem-
perature is high.
Action to take:
Turn on the BCI system again when the
above condition no longer exists.
. “Unavailable Side Radar Obstruction”:
When side radar blockage is detected.
Action to take:
If the warning message appears, park
the vehicle in a safe place, turn the
hybrid system off. Check for and
remove objects obscuring the radar
sensors on the rear bumper, and restart
the hybrid system. If the BSW or BSI
system operates normally, the BCI
system will also operate normally.
(See “BSW/BSI temporarily not avail-
able” (P.5-47).)
BCI malfunction
When the BCI system malfunctions, it will
be turned off automatically, a beep will
sound and BCI system “malfunction”
warning message will appear in the vehicle
information display.
Stop the vehicle in a safe location, turn the
hybrid system off and restart the hybrid system. If the warning message continues
to appear, have the system checked by an
INFINITI retailer.

JVS0232X
SYSTEM MAINTENANCE
.The two radar sensor units*1for the
BSW, BSI and BCI systems are located
near the rear bumper. Always keep the
area near the radar sensors clean. Do
not attach stickers (including transpar-
ent material), install accessories or
apply additional paint near the radar
sensors. Do not strike or damage the
area around the radar sensors. Consult
an INFINITI retailer if the area around
the radar sensors is damaged due to a
collision.
. The BSI system uses the same camera
*2that is used by Active Lane Control, located above the inside mirror.
For maintenance of the camera, see “Lane
camera unit maintenance ”(P.5-29).
Radio frequency statement
For USA
This device complies with part 15 of the
FCC Rules.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NOTE:
The manufacturer is not responsible for
any radio or TV interference caused by
unauthorized modifications to this equip-
ment. Such modifications could void the
user’s authority to operate the equipment.
For Canada
This device complies with Industry Canada
Standard RSS-310.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
Frequency of operation: 24.05GHz
—
24.25GHz
Field Strength: Not greater than 2.5V/m
peak (0.25V/m average) at a distance of 3
m
Starting and driving5-55