2014 Citroen DS3 stop

DS3_en_Chap06_conduite_ed01-2014
Driving
This section describes the use of the parking brake, the manual, electronic   or   automatic   gearbox,   the   gear   shift   indicator   and   Stop   &   Start t

o   help   reduce   fuel   consumption,   hill   start   assist,   the   speed   limiter   to  
a

void   exceeding   a   programmed   speed,   cruise   control   to   maintain   a  
p

rogrammed   speed,   the   rear   parking   sensors   to   detect   obstacles.

DS3_en_Chap06_conduite_ed01-2014
Parking brake
Applying
F Pull  the   parking   brake   lever   fully   up   to  i
mmobilise   your   vehicle.
Releasing
F Pull  the   parking   brake   lever   gently,   press  t
he release button then lower the lever
fully. When
  parking   on   a   slope,   direct   your  w
heels   against   the   pavement,   apply   the  
p

arking   brake   and   engage   a   gear.
When
  the   vehicle   is   being   driven,  
i

f   this   warning   lamp   and   the   STOP
warning
  lamp   come   on,   accompanied  
b

y   an   audible   signal   and   a   message   in   the  
m

ultifunction   screen,   this   indicates   that   the  
p

arking   brake   is   still   on   or   has   not   been  
p

roperly
 r
eleased.

111
DS3_en_Chap06_conduite_ed01-2014
The gear change requests are only carried out if   the   engine   speed   permits.
It is not necessary to release the accelerator
pedal
  during   gear   changes.
When
  braking   or   slowing   down,   the   gearbox  
c

hanges   down   automatically   so   that   the   vehicle  
p

icks   up   in   the   right   gear.
Under
  full   acceleration,   the   change   up   will  
n

ot   take   place   unless   the   driver   operates   the  
g

ear   lever   or   steering   mounted   control   paddle  
(

unless   the   engine   is   close   to   its   maximum  
s

peed).
Reverse
To engage reverse, the vehicle must be immobilised   with   your   foot   on   the   brake.
F

Sel
ect position R .
Stopping the vehicle
Before switching off the engine:
-  c hange   to   position   N to be in neutral,
or
-
 
l
eave   the   vehicle   in   gear;   in   this   case   the  
v

ehicle   cannot   be   moved.
Manual mode
F Select position M.
The   gears   engaged   appear   in  
s

uccession   in   the   instrument   panel.
You
  can   change   mode   at   any   time   by  
m

oving   the   gear   lever   from   A to M or
the
  other   way   round.
Never select neutral (position N ) when
moving. There
  is   an   audible   signal   on  
enga

gement
 o
f
 r
everse.For
  all   parking   situations,   you   must
apply the parking brake
 

to   immobilise  
t

he   vehicle.
When
  immobilising   the   vehicle   with   the  
e

ngine   running,   you   must   put   the   gear  
l

ever into neutral (position N).
Before
  doing   anything   under   the  
b

onnet,   ensure   that   the   gear   lever   is   in  
neu

tral (position N)
  and   that   the   parking  
b

rake   is   applied.
At
  low   speed,   if   reverse   gear   is   requested,  
the N
  warning   lamp   flashes   and   the   gearbox  
g

oes   into   neutral   automatically.
To
  engage   reverse,   put   the   gear   lever   into  
p

osition N, then to position R .
driving

DS3_en_Chap06_conduite_ed01-2014
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
g

ear   lever   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   gear   lever   in
 t

he N
 

position   and   apply   the   parking   brake.
If the lever is not in position P
,
when the driver's door is opened or
approximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the lever to position P ;
 
the
 
m

essage
 d

isappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from   N to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact a CITR
oË

N dealer or a qualified
workshop
 
as   soon   as   possible.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
four
 
gears.
F

P

ush the lever towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the lever towards the -
 
sign
 
to
 
change
 
d

own
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or N 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to
 i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

DS3_en_Chap06_conduite_ed01-2014
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
Going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "E
cO
" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
you
 
p

ress
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
lever
 
i

n position N .
A
 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 d

uring
 
a
 
journey.
 
It
 
rests
 
itself
 t

o
 
zero
 
every
 
time
 
the
 
ignition
 
is
 s

witched
 
on
 
with
 
the
 
key. STOP
  mode   is   not   invoked   when:
- t he driver's door is open,
-

t
he driver's seat belt is not fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(10
  km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "EcO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

11 9
DS3_en_Chap06_conduite_ed01-2014
Going into engine START mode
The "EcO" warning   lamp   goes   off  a
nd   the   engine   starts:
-

w

ith a manual gearbox , when you
depress the clutch pedal,
-

w

ith a 5-speed or 6-speed electronic
gearbox :
●
 
g

ear   lever   in   position   A or M, when you
release
  the   brake   pedal,
●
 
o

r
 
gear   lever   in   position   N   and   the   brake  
p

edal   released,   when   you   move   the   gear  
l

ever to position A or M ,
●
 
o

r
 
when   you   engage   reverse   gear.
Special cases: START invoked
automatically
If the system has been deactivated in   STOP   mode,   the   engine   restarts  
i

mmediately.
At
 
any   time,   press   the   "E
cO O
FF" switch to
deactivate   the   system.
This
 
is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   a   message   in   the  
sc

reen.
deactivation
For reasons of safety and for your comfort, S
TART   mode   is   invoked   automatically   when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
 
t
he   speed   of   the   vehicle   exceeds   7   mph  
(11
  km/h)   with   the   electronic   gearbox  
s

ystem,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   for   control   of   a   system.
The "E
c
O
"
 
warning   lamp   flashes   for  
a

  few   seconds,   then   goes   off.
This operation is perfectly normal.
With
 
a
 
manual
 
gearbox
 
in
 
STOP
 
m

ode,
 
if
 
you
 
engage
 
a
 
gear
 
without
 
f

ully
 
depressing
 
the
 
clutch
 
pedal,
 
a
 
m

essage
 
is
 
displayed
 
asking
 
you
 
to
 
f

ully depress the clutch pedal so that
the
 
engine
 
can
 
restart.
driving

DS3_en_Chap06_conduite_ed01-2014
The system is reactivated automatically at   every   new   start   using   the   key.
Reactivation
This system requires a battery with a special specification   and   technology   (reference  
n

umbers   available   from   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop).
Fitting
  a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
In
 
the
 
event
 
of
 
a
 
fault
 
with
 
the
 
system,
 
the
 
"

E
cO O

FF"
 
switch
 
warning
 
lamp
 
flashes
 
then
 
c

omes
 
on
 
continuously.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
the
 
v

ehicle
 
may
 
stall.
 
All
 
of
 
the
 
instrument
 
panel
 
w

arning
 
lamps
 
come
 
on.
 
It
 
is
 
then
 
necessary
 
t

o
 
switch
 
off
 
the
 
ignition
 
and
 
start
 
the
 
engine
 
a

gain
 
using
 
the
 
key.
Operating fault Maintenance
Before doing anything under the b
onnet, deactivate the Stop & Start
system
  to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
The
  Stop   &   Start   system   makes   use  
o

f   advanced   technology.   All   work  
o

n   this   type   of   battery   must   be   done  
b

y a CITR
oË
N dealer or a qualified
workshop.
Press the "EcO O
FF"
 
switch
 
again.
The
 
system
 
is
 
active
 
again;
 
this
 
is
 
confirmed
 
b

y
 
the
 
switch
 
warning
 
lamp
 
going
 
off,
 
a

ccompanied
 
by
 
a
 
message
 
in
 
the
 
screen.

Under-inflation detection
System which automatically checks the pressures of the tyres while driving.
T he   under-inflation   detection   system  
d

oes   not   replace   the   vigilance   or   the  
r

esponsibility   of   the   driver.
This
  system   does   not   avoid   the   need   to  
c

heck   the   tyre   pressures   (including   the  
s

pare   wheel)   every   month   as   well   as  
b

efore   a   long   journey.
Driving
  with   under-inflated   tyres  
i

mpairs   road   holding,   extends   braking  
d

istances   and   causes   premature  
t

yre wear, particularly under arduous
condition
  (high   loading,   high   speed,  
lon

g
 jo
urney).The inflation pressures defined for
your vehicle can be found on the tyre
pressure
  label.
See
  the   "Identification   markings"  
s

ection.
Tyre
  pressures   should   be   checked  
w

hen the tyres are "cold" (vehicle
stopped
  for   1   hour   or   after   a   journey   of  
l

ess   than   6   miles   (10   km)   at   moderate  
s

peeds).
Other wise
  (when   hot),   add   0.3   bar   to  
t

he   pressures   shown   on   the   label.
Driving
  with   under-inflated   tyres  
i

ncreases   fuel   consumption.
The
  system   monitors   the   pressures   in   the   four  
t

yres,   once   the   vehicle   is   moving.
It
  compares   the   information   given   by   the   four  
w

heel speed sensors with reference values,
which must be reinitialised ever y time the
tyre pressures are adjusted or a wheel
changed .
The
  system   triggers   an   alert   as   soon   as   it  
d

etects a drop in the inflation pressure of one
or
  more   tyres.