2014 AUDI TT ROADSTER warning

was manufactured. Please see c> page 193,
Speed rating (letter code)
for a listing of the
speed rat ing letter codes and the maximum
speed at which the tires can be driven .
The speed rating letter code
( c> page 184) is
on the side wall of the tire
c::> page 192 .
A WARNING
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed. Always know the maximum
speed before driving off . Never drive faster
than the speed permitted for your specific
w inte r tires . This will cause damage to the
tires leading to an acc ident and serious
personal injury to you and yo ur passen­
gers .
A WARNING
Driving faster than the maximum speed
for which the winter tires on your vehicle
were designed can cause tire fai lure in­
cluding a blowout and sudden deflation,
loss of control, crashes and serious per­
sonal injuries . Have worn or damaged tires
replaced immed iately.
- Winter tires have maximum speed rat ing
that may be lower than your veh icle's
maximum speed .
- Never drive faster than the speed for
wh ich the winter or other tires installed
on your vehicle are rated .
A WARNING
Always adjust your driving to the road and
traffic conditions. Never let the good ac­
celeration of the winte r tires and all-whee l
drive tempt you into taking extra r is k s . A l­
ways remember:
- When brak ing, an a ll-wheel drive vehicle
hand les in the same way as a front drive
vehicle.
- Drive carefu lly and reduce your speed on
icy and slippery roads, even winter tires
cannot he lp under black ice conditions.
Tire s an d wheel s 197
@) For the sake of the env ironment
Use summer tires when weather condi­
tions permit. They are quieter, do not wear
as quickly and reduce fuel consumption.
Snow chains
Snow cha ins may be fitted only to the front
wheels, and only to certain tire sizes . Ask your
authorized Aud i dealer on which tire sizes
snow chains can be used .
If you are go ing to use snow chains, then you
must install them on the front wheels at
least .
The snow chains mus t have low-prof ile links
and must not be th icker than 0 .53 inch
(13.5 mm), includ ing the lock.
Remove wheel center covers and trim discs
before putting snow chains on your vehicle
c::> (D . For safety reasons cover caps must then
be fitted over the wheel bolts . These are avail ­
able from authorized Aud i dealers.
A WARNING
Using the wrong snow chains for your vehi­
cle or insta lling them incorrect ly can in­
crease the risk of loss of cont ro l leading to
serious personal injury.
- Snow chains are available in different
sizes . Always make sure to follow the in­
structions provided by the snow chain manufacturer .
- When driving with snow chains never drive faster than the speed permitted for
your specific snow chains.
- Always observe local regulations .
(D Note
-Remove snow chains before dr iv ing on
roads not covered with snow to avoid
damaging tires and wearing the snow
chains down unnecessarily.
- Snow chains, which come into direc t con­
tact with the whee l rim, can scratch or
damage it . Therefore, make sure that the .,.
•
•

198 Tire s and wheel s
snow cha ins a re suitab ly covered. Check
the position of the snow chains after driving a few yards and correct if neces ­
sary. Follow the instr uctions from the
snow cha in manufacturer when doing so.
{O) Tips
Where snow cha ins are mandatory oncer­
tain roads, this norma lly also applies to
veh icles with all-wheel dr ive.
Wheel bolts
Wheel bolts must always be tightened to the
correc t torque .
The design of whee l bolts is matched to the
factory installed r ims . If different rims are fit ­
ted, the correct wheel bolt s with the r ight
length and correctly shaped bol t heads mus t
be used . This ensures that wheel s are fitted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bolts from a d iffe rent vehicle -even if it
i s the same model
Q page 228.
A WARNING
Imprope rly tig htened o r maintained whee l
bolts can be come loose ca using loss of
cont ro l, a co llision and serious person al in­
jury .
- Always keep the w heel bol ts and the
t h reads in t he wheel hubs clean so the
wheel bolts can t urn easily and be p rop ­
er ly t ightened .
- N ever grease or oil the wheel bo lt s an d
the threads in the wheel h ubs. They can
become loose w hile d riving if greased or
oi led, even if tightened to the specif ied
torque.
- Only use whee l bolts that be long to the
rim being installed.
- Never use different whee ls bolts on your
vehicle .
- Always mai ntai n the co rrect tighte ning
torq ue for the wheel bolts to reduce the
risk of a wheel loss. If the tightening tor- que of the whee
l bolts is too low, they
can loosen and come out when the vehi­
cle is mov ing. If the tig hte ning torq ue is
too high, the w heel bolts a nd threads
can be damaged and the whee l can be­
come loose.
(D Note
The specified torque for t he whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm). Torque whee l bolts diago­
nally . After changing a whee l, the to rq ue
must be checked as soon as possible with a
torque w rench - prefe rably by an author­
iz ed A udi dealer or quali fied workshop .
Low aspect ratio tires
Your Audi is factory-eq uipped w ith low aspect
ratio tires. These tires have b een tho ro ughly
tested and been se lected specifically for your
model for their supe rb performance, road fee l
and hand ling under a variety of driving condi­
t ions . Ask your author ized Audi dealer for
more de tails .
The low aspect ratio of these t ires is ind icated
by a numeral of
55 or less in the tire 's s ize
designation . The numera l rep resents the ratio
of the tire 's s idewa ll height in relation to its
t read width exp ressed in percentage. Conven­
tiona l tire s have a he igh t/w idth rat io of 60 or
more.
The p erformance of low-a spect-ratio tire s is
particularly sensitiv e to improper inflation
pre ssure. It i s ther efore important that low
aspect ratio tires are inflated to the specified
pre ssure and that the inflation pre ssure i s
regularly checked and maintained. Tire pre s­
sures should be checked at least once a month and always before a long trip
Q page 187, Checking tire pressure.
What you can do to avo id tire and rim
damage
Low aspect ratio tires can be damaged mo re
easily by impact w ith po tholes, curbs, gul lies ..,.

200 Tires and wheels
remain continuo usly illuminated . This se­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunction indicator is illuminat­
ed, the system may not be able to detect or
signal low tire pressure as intended. TPMS
malfunctions may occur for a variety of rea­
sons, including the installation of replace­ ment or alternate tires or wheels on the vehi­
cle that prevent the TPMS from functioning properly . Always check the TPMS malfunction
tellta le after replacing one or more t ires or
wheels on your veh icle to ensure that the re­
placement or alternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 143 Display : underi nflat io n warn ing
Using the ABS sensors, the tire pressure moni­
toring sys tem compares the t ire tread circum­
ference and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or more tires, th is is indicated in the instru­
ment clus ter with a warning symbo l
ail and a
message<>
fig. 143. The dr iver message in the
display goes out after 5 seconds . The driver
message can be displayed again by pressing
the
! CHECK I button @¢ page 10, fig . 3 . If on ­
l y one tire is affected, the display will indicate
its pos ition.
The tire press ure monitoring m ust be reset in
the menu display each time the pressures are
ad justed (e.g. when switching between parti- al and fu
ll load pressure) or after changing or
replacing a tire on your vehicle<>
page 201.
The TPMS indicator only mon itors the t ire
pressure that you have previously stored . You
can find the recommended tire pressures for
your vehicle on the label on the driver's door
pillar
¢ page 185.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire pressure in one or more tires is too
low,
- the tire has structural damage,
- the tire pressure was changed, wheels rotat -
ed or replaced but the TPMS was not reset
¢ page 201.
Warning symbols
ail Loss of pressure in at least one tire¢& .
Check the tire or tires and replace or repa ir if
necessary . The indicator light
HE in the instru­
ment cluster also illuminates
<>page 13.
Check/correct the pressures of all four tires
and reset TPMS in the menu display .
ffim (T ire Pressure Monitoring System) Tire
pressure! System malfunction. Ifffim
ap­
pears after switching the ignition on or while
driv ing and the indicator lig ht
HE in the in­
strument cluster blinks for approx ima tely one
minute and then stays on, there is a system
malfunction .
At tempt to store the correct tire pressure
¢ page 201. Ifthe indicator light does not
turn
off or if it turns on shortly thereafter, im ­
med iate ly drive your vehicle to an author ized
Audi dealer or author ized repair facility to
have the malfunction corrected.
_&. WARNING
-
- If the tire pressure indicat or appears in
the instrument cluster display, one or
more of your tires is significant ly under­
inflated . Reduce your speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures.
IJJ,,

When it i s not po ssibl e to co ntinu e
d riv ing, even with run-fl at ti res?
-If the E lectronic Stabilization Control (ESC)
is not working or keeps coming on.
- If the Tire P ressure Monitoring System does
not work .
- If the tire has been severely damaged, in a
crash, for example. The tread can separate
from a damaged tire as the whee l turns, and
hit parts of the vehicle, such as the fuel tank
filler neck, fuel lines or brake lines.
- Do not continue dr iving if severe vibration
occurs or if the tire starts to smoke because
the tire is runn ing hot .
- Do not continue driving if damage to the
tire, such as cracks in the sidewall, appears.
A WARNING
Improper use of run-flat t ires can cause
vehicle damage that can lead to loss of ve­
hicle control, a crash and serious personal
injury.
- Run-flat tires can only be used with spe­
c ial rims.
- Run-flat tires must always be mon itored
with a properly programmed Tire Pre­
ss ure Mon itor ing System.
- Always inspect a tire that has lost air to
make su re it is safe to drive w ith the t ire
in the run-flat mode.
- Never drive with run-flat tires that have
been damaged in a collision.
- Never drive with run-flat tires if heat
build-up causes the t ire to give off
smoke.
- Never drive with run-flat tires if the vehi­
cle shakes or v ibrates severely.
- Never drive with a run-flat tire that de­
velops sidewall cracks or other damage
wh ile in use .
- If you switch between standard and run­
flat tires, an author ized Audi dealer or
qualified wo rkshop must reprogram the
control module.
Tire s an d wheel s 203
@ Note
Run-f lat ti res have special characteristics
and requirements, that are very different
from convent ional tires. Run-flat tires re­
quire special rims for run-flat use and can­
not be used on conventional whee l rims .
(D Tips
- If you are not able to cont inue driving
w ith run-flat tires, please seek professio­
nal ass istance.
- Please contact your authorized Audi
dealer or Aud i of America, Inc . if you
have questions about t ires and rims.
Driving with run-flat tires
Applies to veh icles: w it h Run -flat t ires
Handling characteristics change when tire
pressure is low.
Driving on tires with low tire pressure changes
the way a veh icle handles, particularly when
corner ing and braking. The handling charac­
teristics of run -flat tires do not seem to
change a lot even when driving on low pres­
sure or in the run-flat mode . Nevertheless you
must still take specia l precautions whe n oper ­
at ing a veh icle on run-flat tires when t ire pres­
s u re is low o r the tire(s) is flat:
" The Electronic Stabilization Contro l (E SC)
must be switched on.
" Never drive fas ter than 50 mph (80 km/h)
q .&_ .
"Plan ahead when driving and anticipate
what you will have to do considering traffic
and road conditions up ahead.
" Accelerate carefully.
" Avo id unnecessary and sudden steering and
braking maneuvers.
" Reduce your speed in plenty of t ime before
intersections, curves and other places where
you may have to react quickly .
Please see:
q page 203, When it is not possi­
ble to continue driving, even with run-flat tires?
•
•
...

204 Tires and wheels
Handling characteristics change when
dr iving with low air pressure or with flat
tires even with special run-flat tires
A low pressure or flat front tire affects vehicle
handling characteristics by pulling the vehicle
slightly to the side where the tire is mounted
and reduces braking performance.
A low pressure or flat
rear tire also affects
driving characteristics by pul ling to the side
where the tire is mounted and also reduces
brak ing performance. The effect on vehicle
handling is most not iceable when driving
around curves.
& WARNING
Changed vehicle handling characteristics
when driving in the run -flat mode can
cause loss of vehicle contro l, a c rash and
serious personal in jury.
- Driving on special run-flat tires in the
run-flat mode will change vehicle han­
dling characteristics during braking,
when cornering and under heavy acceler­
ation .
- Never drive faster than the maximum
rated speed of 50 mph (80 km/h) when
dr iv ing in the run-flat mode .
- Always adjust vehicle speed to traffic,
road and weather cond itions and drive
slower than the max imum rated speed if
necessary weather and road conditions
are taken into account.
- Always obey speed limits and other traf­
fic laws.
(D Note
We a lways recommend driving w ith even
more care when using these specia l tires in
the run-flat mode. Always avo id sudden
maneuvers.
Replacing run-flat tires and rims
Applies to veh icles: w it h Run -flat tires
Your vehicle was especially designed to use
special run-flat tires .
You may use and combine only approved run­
flat tires and special matching rims that have
been designed for run -flat tires . Mounting
special run-flat tires on standard whee ls will
not work and will not provide the advantages
fo the run-falt feature. Never use special run­
flat tires on standa rd whee l rims.
After dr iving w ith a t ire in the run-flat mode,
always have the veh icle and affected tire(s)
and rim(s) inspected by an author ized Audi
dealer. Tires that have been dr iven in the run­
flat mode must be rep laced .
& WARNING
=
Use of damaged run-flat tires and rims can
cause vehicle damage that can lead to loss
of vehicle control, a crash and serious per­
sonal injury.
- Always have the vehicle and affected
tire(s) and r im(s) inspected by an author­
ized Audi dealer after driving a tire in the
run-flat mode.
- Tir es that have been dr iven in the run­
flat mode must be replaced.

What do I do now? Trunk escape handle
In case of an emergency, the rear lid can be
opened from the inside using the trunk es­
cape handle .
Fig. 148 Luggage compa rtment: Tr unk escape handle
"' To open the trunk lid pu ll the handle down
as indicated by the -arrow-~
fig. 148.
The trunk escape handle inside the storage
compartment is made of fluorescent materia l
to g low in the dark.
& WARNING
The trunk escape handle is to be used only
in an emergency .
Vehicle tool kit
The tools ore stored underneath the floor
panel in the luggage compartment.
F ig. 1 49 Luggage co mpa rt ment : veh icle tool ki t
"'Swing the luggage compartment floor up­
wards.
"' Remove the vehicle tool k it.
The onboard tool kit includes:
What do I d o now ? 205
- Hook for removing wheel covers*
- Plastic clip to remove wheel bo lt covers*
- Wheel bolt w rench
- Alignment pin for changing wheels
- Screwdriver with reversible blade
- Replacement bit (reversible Torx bit for changing lamps)
- Open ended wrench 10 x 13
- Towing eye
- Jack*
Some of the on board items listed above are
provided on ce rtain mode ls only or are option­
al ext ras.
Before returning the jack* to its place, retract
the jack arm fu lly.
& WARNING
Improper use of the vehicle jack can cause
serious pe rsonal injuries .
- Never use the screw drive r hex head to
tighten wheel bo lts, since the bolts can­
not attain the necessary tighte ning tor­
que if you use the hex head, potentially
causing an accident.
- The factory-supplied jack is intended on­
ly for yo ur vehicle model. Under no ci r­
cumstances should it be used to lift
heavy veh icles or other loads; you risk in­
juring yourself .
- Never start the engine when the vehicle
is raised, wh ich could cause an accident.
- Support the vehicle securely with appro­
priate stands if work is to be performed
underneath the vehicle; otherwise, there
is a potential risk for injury.
- Never use the jack supplied with your Audi on another vehicle, particularly on a heav ier one . The jack is only suitable for
use on the veh icle it came with .

206 What do I do now?
Tire repair
General and safety pointers
Applies to vehicles: with Tire Mobility System
Tire repair is intended only for temporary,
short -term use .
Fig. 150 Tire da mage for wh ich the Tire Mob ility Sys ­
tem is not suited
Your vehicle is equipped with a tire repair kit,
the
Tire Mobil ity System (TMS ).
In the event of a tire fa ilure, the TMS is in the
luggage compartment under the floor. It con­
sists of the tire sealant and an electric air
pump.
Using
TMS , tire damage caused by foreign
bodies up to about
0.16 inch (4 mm) in diam­
eter can be sealed reliably.
The foreign object can stay in the tire.
The tire sealant must not be used :
-for cuts or punctures in the tire which are
larger than 0.16 inch (4 mm)
r=::> fig. 150 @
-for damage to the rim@
- if you have been driving with very low tire
pressures or t ires with no air®
Using the
TMS is described in the section
r=::> page 207, Preliminary steps.
TMS can be used at temperatures down to
- 4 °F (- 20 °() .
.&_ WARNING
Take the following preca utions after re­
pairing the tire:
-
- Do not drive faster than SO mph (80 km/
h)! -
Avoid full-throttle acceleration , heavy
braking and fast cornering.
- The vehicle's road behavior can be affect­
ed.
- Tires sea led with
TMS are intended only
for
temporary, short-term use.
-After using the tire sealant the tire pres­
sure monitoring system may no longer
work properly. Drive carefully to the next
professional repair facility.
- TMS must NOT be used,
- for cuts or punctures in the t ire which
are larger than 0.16 inch (4 mm)
- for damage to the rim
- if you have been driving with very low
tire pressures or tires with no air
- Seek professional assistance if it is not
possible to repair the tire with the tire
sealant.
.&_ WARNING
The t ire sea lant must not come into con ­
tact with skin, eyes or clothing.
- If you get any ti re sealant in your eyes or
come into contact w ith it, rinse the af ­
fected area thoroughly with clean water .
Find a phys ician immediately!
- Change any clothing contaminated with
tire sealant immediately .
- Do not inhale the vapor!
- If you have swallowed tire sealant, rinse
your mouth thoroughly right away and
drink plenty of water.
- Do not induce vomiting! Find a physi­
cian immediately!
- If you have allergic reactions, find a
physician immediately .
- Keep the tire sealant away from children.
(D Note
Do not use commercially available tire
sealants . The e lectr ica l components of the
tire pressure monitoring system will no
longer work properly.

@ For the sake of the environment
Used sealant bottles can be dropped off at
a recycling facility .
@ Tips
-If sealant has run out, allow it to dry.
Then you can peel it off.
- Have the tire sealant replaced every 4
years at a dealership .
Preliminary steps
Applies to vehicles: with Tire Mobil ity System
Some preliminary steps are necessary for tire
repair.
Fig. 151 Luggage co mpa rt ment : Tir e Mobil ity System
1> Jf you have a flat tire, park the veh icle as far
as possible from mov ing traffic .
.,. Apply the
parking brak e firmly .
.,. Move the
se le ctor l ever to the P po sit ion .
.,. Check whether a repa ir using the Tire Mob ili­
ty System is possible ¢
page 206, General
and safety poin ters .
.,. Have all passengers leave the vehicle and
stay away from the danger zone ¢
A.
.,. Take the se alant bottle and the ele ctri c air
pump
from the luggage compartment un­
der the floor¢
fig. 15 l .
.,. Remove the "max. 50 mph" (80 km/h) stick­
er from the sealant bottle and aff ix it to the
inst rument cluste r in the driver's v iew .
..&, WARNING
-Turn the ha zard flashers on and set up
th e war ning t ria ng le if you have a fla t
t ire in moving t raff ic. In this way you p ro­
tect yo urself and other road users .
-
What do I do now ? 207
-Make sure that all passengers are in a
safe place, out of the danger zone (for
example, behind a guard rail).
(D Note
Particular care is necessary if you are mak­
ing a tire repair on a steep incline.
(D Tips
Obey all laws.
Making a tire repair
Applies to vehicles : wit h Tire Mob ility System
Tire repair consists of the following sec tion s.
Fi g. 1 52 Parts of t he T ire Mobility System
Fi g. 1 53 Connector for th e Tire Mob ility System
Assembling Ti re Mobility System
.,. Open the lid @of the electr ic air p ump
¢ fig. 152 .
.,. Pull the plug@) and the pressure hose®
w ith the gauge out of the housing .
.,. Screw the pressure hose® of the e lectric
air pump onto the flange ® of the sealant
bott le @ .
.,. Push the sealant bott le w ith the flange
down into the recess @ on th e lid of th e
elec tric air pump.
IJ,-