2014 AUDI TT COUPE service

Downloaded from www.Manualslib.com manuals search engine Intelligent
technology
event of faults or anomalies in the vehicle data,
only these data are saved. As a rule, faults are
shown by the warning lamps in the instrument
cluster.
Data saved in the control units can only be read
and analysed with special equipment.
A qualified workshop is only able to recognise
and deal with faults by using the relevant saved
data. Among other things, the saved data may
contain the following information:
- Data relating to the engine and the gearbox
-Speed
- Dire ction of travel
- Braking force
- Seat belt warning system data
The control
units
installed will not under any cir­
cumstances record conversations in the vehicle.
On vehicles with an automatic SOS dial system
via a mobile phone or another connected device,
the current location of the vehicle can be trans­
mitted. In accidents where the control units reg­
ister that airbags have been triggered, a signal
can automatically be sent by the system. This de­
pends on the service provider. The signal can only
be sent in areas with sufficient mobile phone cov­
erage.
Event data recorder
Your vehicle is not equipped with an event data
recorder.
In an event data recorder, information about the
vehicle is temporarily saved. In the event of an
accident, you can therefore obtain detailed infor­
mation about the course of events. On vehicles
with an airbag system, accident-related data such
as impact speed, seat belt status, seat positions
and trigger times can be saved. The exact infor­
mation saved depends on the manufacturer.
The installation of an event data recorder is sub­
ject to the agreement of the vehicle's owner. This
process is governed by legislation in some coun­
tries.
108 Reprogram
ming control units
All data for controlling components are saved in
the control units. Some convenience features,
such as one-touch signalling, single door unlock­
ing and display messages can be reprogrammed
using special workshop equipment. If any con­
venience features are reprogrammed, the infor­
mation in this Owner's Manual will no longer be
accurate for the features that have been
changed. We recommend having the reprogram­
ming confirmed by an Audi workshop in the
"Workshop remarks" section of your Service
Schedule.
Your Audi dealer will be able to provide you with
information about possible reprogramming op­
tions.
Event memory
There is a diagnostic connection for reading out
the event memory located in the footwell on the
driver's side of the vehicle. Information regarding
the operation and status of the vehicle's elec­
tronic control units is stored in the event memo­
ry. The event memory should only be read out
and erased by a qualified workshop.
A WARNING
The diagnostic connection must not be used
for other purposes. Incorrect use can cause
malfunctions -risk of accident!

Downloaded from www.Manualslib.com manuals search engine Speech
dialogue system
Telephone
Applies to vehicles: with speech dialogue system and telephone
Important: A mobile phone must be connected
to the MMI ¢page 123, and the Telephone
menu must be open ¢ table on page 117.
Function Say:
Calling a contact from the directory Call
(XV), e.g. Call John Smith
Dialling a specific number stored
for a contact
Dialling a phone number when an
address card is open
Calling a contact from the favour-
ites List
Displaying the call List
Calling the Last number dialled
Dialling a telephone number
Correcting an entered phone num-
ber
Displaying contact information
Listening to voice mail messages
Entering the SIM PIN code
Correcting an entered PIN
Correcting an entry
Closing the full List of commands Call
(XV) business / private / land line/ mobile,
e.g. Call John Smith private
Call / Call business number/ Call private number/ Call land
line / Call business mobile
Telephone favourites > desired contact when requested > Dial
Call list
Redial
Enter number > enter phone number in blocks of individual dig-
its when requested, e.g. 07441 234 567 > Dial
Correction / Delete number
Directory > desired contact when requested,
e.g. John Smith
Call mailbox
Enter PIN > enter PIN in individual digits when requested >
Store
Correction / Delete PIN
No, I meant (XV)
Close
"surname, first name") and by saying only
the first name or surname.
- If you have a mobile phone that transmits
first names and surnames separately, you
can select directory contacts both by enter­
ing the full name ("first name, surname" or -
For more information on which mobile
phones are supported, please go to
www.audi.com/bluetooth or contact an Audi
dealer.
Audi connect
Applies to vehicles: with speech dialogue system and Audi connect
Important: The requirements for Audi connect
must be met ¢page 137.
Function Say:
Calling up an Audi connect service
I Audi connect > follow the directions given by the system
118

Downloaded from www.Manualslib.com manuals search engine Speech
dialogue system
Function Say:
Starting route guidance after enter-
Start route guidance
ing a destination
Cancelling the active route guidance
Stop route guidance
Calculating alternative routes
Calculate alternative routes
Entering a special destination with
Special destination > Change search area > enter desired cote-
search area with assistance from
gory or subcategory when requested, e.g. "Restaurant"
the system
Categories for entering special des-
Audi Service / Railway station/ Airport/ Hotel/ Hospital /
ti nations
Parking space/ Service area/ Restaurant/ Filling station etc.
Search areas for entering special
In immediate vicinity/ In vicinity of route / In vicinity of desti-
destinations nation/ In vicinity of stopover / In new town/ In new country
Entering an online destination* Online destination (XV), e.g. "Online destination Palace Hotel"
Correcting an entry
No, I meant (XV)
Closing the full list of commands
Close
You can say the following commands to make ad­
ditional navigation settings:
Function
General map options
Map type
Displaying the route list
Displaying remaining distance/time
while route guidance is active
Highest speed query
Setting the navigation cues during
active route guidance
Dynamic traffic avoidance
Excluding the next section of the
route
Excluding a certain section of the
route
(©) Note Say:
Map / Day map/ Night map/ Change map colours automati-
cally
20 driving position map/ 20 north position map/ 30 map/
Destination map/ Overview map/ Standard map/ Traffic
map / Google Earth map
Route list
Destination info
How fast can I go here?
Voice guidance on/ Voice guidance off/ Voice guidance com-
pact / Voice guidance complete/ Voice guidance traffic
Manual traffic avoidance / Automatic traffic avoidance /
Switch off traffic avoidance
Exclude route
Exclude route for (XV) metres/kilometres/yards/miles / Ex-
elude next street/ Exclude next section of route
spell destinations to enter them for route
guidance.
- Depending on the selected menu language
and the country you are in, you may have to -
Please observe the notes in the chapter
Notes on Audi connect ¢ page 145.
120

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... In
addition, the contacts on the mobile phone are
automatically Loaded into the directory of the
MMI. This may take several minutes, depending
on how many contacts are stored on the mobile
phone.
After you have connected your mobile phone to
the MMI successfully, you can immediately begin
configuring Audi connect ¢page 137.
{i)) Note
- You can adjust further settings for connec­
ted mobile phones using the connection
manager ¢page 187.
- Bluetooth devices only have to be bonded
once. Any devices that have already been
bonded to the MMI system are connected
automatically when they are within range
and the ignition is on.
- You will need to authorise the MMI connec­
tion on your mobile phone to enable auto­
matic connection.
- Please note any system queries on your mo­
bile phone, e.g. whether the phone should
connect automatically in the future. On
some mobile phones, you may also need to
download the directory and allow access to
your text messages separately.
- You receive the SIM PIN code from your mo­
bile network service provider together with
the SIM card. If you enter the SIM PIN code
incorrectly three times1
)
in a row, the SIM
card will be be blocked. A PUK (personal un­
blocking key) must be entered in order to re­
activate the SIM card.
- You can bond several mobile phones to the
MMI system; however only one connection
is active at a time.
- Any Bluetooth device that is already connec­
ted to the MMI system is disconnected
when another device is connected to the
system.
- The Bluetooth connection between the sys­
tem and the mobile phone is automatically
terminated when you Leave the car.
l l
The number of possible attempts depends on the SIM
card. Telephone
- For further information regarding your mo­
bile phone, contact your mobile network
service provider or refer to the operating in­
structions for your mobile phone. For infor­
mation on using a phone in your car, please
go online (e.g. www.audi.com/bluetooth) or
ask an Audi dealer.
Using the Audi phone box
Applies to vehicles: with Audi phone box
With the Audi phone box*, you can use the vehi­
cle's external aerial to make calls. You can also
charge your phone with a USB adapter. The use
of the external aerial reduces radiation in the ve­
hicle and also ensures better reception quality.
Fig. 130 Using the Audi phone box
The Audi phone box is Located in the centre con­
sole's storage compartment¢ page 6, Fig. 2.
Impor tant: A mobile phone must be connected
via Bluetooth ¢ page 123.
- To establish a connection with the external car
aerial: Place your mobile phone onto the mid­
dle of the telephone symbol in the Audi phone
box with the phone's display facing upwards.
When doing so, make sure that there are no ob­
jects between the Audi phone box and the mo­
bile phone.
- To charge a mobile phone with a USB adapter:
Connect your mobile phone to the USB socket
@ ¢Fig. 130 using a USB charging cable.
For ease of use, Audi offers special USB adapters*
¢ page 174, Fig. 161. The following USB adapt-
ers are currently available:
.,..
125

Downloaded from www.Manualslib.com manuals search engine Telephone
® USB adapter for mobile phones with micro
USB connector*
@ USB adapter for mobile phones with Apple
Lightning connector*
© USB adapter for mobile phones with Apple
dock connector*
_& WARNING
Loose objects can be flung around in the pas­
senger compartment in the event of sudden
driving or braking manoeuvres. This could re­
sult in serious injuries and also cause you to
lose control of the vehicle. Always keep the
centre armrest closed when driving.
- The Audi phone box is not available in all
countries. Your Audi dealer will be able to
provide you with more detailed information.
- If the mobile phone is placed in the Audi
phone box in a bag or a protective case, this
may interfere with the connection to the ex­
ternal aerial.
- An enhanced transmission quality cannot be
guaranteed if more than one mobile phone
is placed inside.
- Audi recommends the use of Audi Genuine
Accessories. Audi has tested these products
for suitability, reliability and safety.
- USB adapters are available from Audi deal­
ers or specialist retailers.
- To avoid malfunctions, ensure that the mo­
bile phone is correctly placed inside the Audi
phone box.
Using the SIM card reader
Applies to vehicles: with SIM card reader
You can choose how you wish to make telephone
calls when you insert a separate SIM card in the
SIM card reader:
Telephone installed in vehicle (SIM card)*
The SIM card in the SIM card reader is used both
for telephone calls and Audi connect services
¢page 137.
126 Your
telephone conversations are directed via the
external vehicle aerial to optimise sound and re­
ception quality. For the telephone options, you
can be reached on the telephone number of the
SIM card in the SIM card reader. Depending on
the SIM card type, this may be the same number
as for your the current mobile phone contract
(twin/Multi SIM card) or another number from a
different mobile phone contract.
Personal mobile phone (Bluetooth)
Calls are made with the mobile phone connected
using the Handsfree function. You can therefore
be reached on the phone number of the SIM card
in your mobile phone. In this case, the SIM card
in the SIM card reader is used for Audi connect
services only.
Using a separate SIM card
Applies to vehicles: with SIM card reader
Fig. 131 Inserting the SIM card (mini SIM card, actual
size)
Requirements
The vehicle must be stationary , the ignition must
be switched on and the Telephone menu must
have been called up.
liJ.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D Lfl
N
Lfl
.... Using a
separate SIM card
• Insert your mini SIM card (printed side facing
up, contact surface facing down) into the slot
of the card reader ¢Fig. 131. The missing cor­
ner of the SIM card should be at the front left.
Then push the SIM card into the slot until you
feel it engage.
• If requested, enter the PIN code for your SIM
card in the MMI.
• Select and confirm OK.
• To allow the MMI to connect automatically in
the future, select and confirm Yes.
• Select and confirm either Telephone installed
in vehicle (SIM card} or Personal mobile
phone (Bluetooth} ¢ page 126.
• Confirm the message shown by selecting Ac­
cept this time, Always accept or Decline, de­
pending on whether or not you wish to allow a
data connection for Audi connect services to be
established.
After connecting succes sfully
After connecting successfully, one or two signal
strength bars (depending on the connection type)
will be displayed in the status line of the infotain­
ment display.
You can specify whether you wish to make calls
using the SIM card in the SIM card reader or your
mobile phone via I MENU I> Settings > left control
button > MMI settings > Connection manager
¢ page 188. This can also be done retrospective­
ly.
In addition, the contacts on the mobile phone are
automatically loaded into the directory of the
MMI. This may take several minutes, depending
on how many contacts are stored on the mobile
phone.
Rem oving a SIM card
.. Briefly press the SIM card. The card will then
eject from the slot. Remove the SIM card.
Q)) Note
If your mobile phone does not support the
SIM Access Profile (e.g. iPhone), you can also
use the contacts from your mobile phone by
connecting the mobile phone to the system Telephone
via the Directory/contacts profile
¢page 188.
Using the telephone
Calling up the telephone
Applies to vehicles: with telephone
Fig. 132 Telephone functions in the selection menu
Important: A mobile phone must be connected
to the MMI ¢ page 123, or a SIM card must be
inserted in the SIM card reader* ¢ page 126... Selec t: !T
EL! button
> left control button.
The following telephone functions are available
¢Fig. 132:
CD Call list ¢page 128
@ Favourites ¢page 129
@ Directory ¢ page 131
@ Enter number ¢ page 128
® Text message (SIM card)* /Text message (mo­
bile phone)* ¢ page 130
127

Downloaded from www.Manualslib.com manuals search engine Telephone
Di alling a telephone number
Fig. 133 Dialling a telephone number from the call list
Fig. 134 Speller for numbers Sele
ct: !TEL! button > Left control button.
Call List
Important: A telephone number must be stored
in the call List.
Select and confirm the desired telephone number
in the call List.
Symbols in the call List¢ Fig. 133:
CD Missed calls
@ Numbers dialled
@ Received calls
Favourites
Important: A telephone number or a contact
must have been added as a favourite
¢page 129.
Select and confirm a favourite in the favourites
List.
Directory
You can dial a telephone number directly from
the directory ¢page 131.
128 Enter
number
- To enter a telephone number using numbers:
Enter a telephone number using the speller for
numbers ¢ Fig. 134.
- To enter a telephone number using letters: Se­
lect !ABC!
using the speller for numbers. Enter a
series of letters, e.g. AUD/SERVICE using the
speller for Letters.
- To dial a telephone number: Select and con­
firm t". Or: Push the rotary pushbutton down­
wards. Select and confirm OK.
- To delete letters/numbers individually: Select
and confirm - To delete all the numbers/letters you have en­
tered at once: Turn the speller to and hold the rotary pushbutton. Or: Press the
right control button and select and confirm
Clear entry field.
You can enter DTMF tones ("touch-tones") using
the speller while you are talking on the phone.
Answering and ending telephone calls
Applies to vehicles: with telephone
- To answer an incoming call: Select and confirm
Answer.
- To decline an incoming call: Select and confirm
Decline.
- To mute an incoming call: Select and confirm
Mute.
- To end a call/cancel the dialling process: Press
the rotary pushbutton (End call).
To answer a further call: If you are already talk­
ing on the phone when someone else calls, select
Answer to place the current call on hold and to
answer the incoming call. If you select Ignore,
the incoming call will be declined.
Caller information: Depending on whether the
caller is stored in the directory and whether the
telephone number is transmitted with the call,
the caller's name, his/her telephone number or
Unknown will appear on the infotainment dis-
play. A photo of the caller may also be shown if
one has been assigned to the contact in your mo­
bile phone and transmitted to the MMI. You can ..,.

Downloaded from www.Manualslib.com manuals search engine 0
N
co
....
\D L/'l
N
L/'l
.... find
out if your mobile phone supports this func­
tion by asking your mobile network provider, con­
sulting the operating manual of your mobile
phone or visiting www.audi.com/bluetooth.
@ Note
Radio/media playback is muted when you
make or receive phone calls.
During a telephone call
Applies to vehicles: with telephone
Important: A call must be in progress.
.,. Press
the right control button.
The following options may be available during a
call depending on the mobile phone being used
and the type of connection:
- To make a further call: Select Find contact >
Call list/Directory/Favourites > entry in List.
- To answer a further call when you are talking
on the phone and have another call on hold:
Select Replace. The current call will be replaced
by the incoming call.
Other functions are:
Switch microphone off: If you select and confirm
this option, the caller will no longer be able to
hear you; you will still be able to hear the caller.
Hold/Resume: You can put a call on hold and re­
trieve it later from the hold queue. Select and
confirm a call to resume it.
Transfer to mobile/Retrieve call*: By selecting
Transfer to mobile, you can transfer your current
call from the MMI to your mobile phone. Select­
ing Retrieve call transfers the call from your mo­
bile phone back to the MMI.
Switch: You can switch between two phone calls
(one of them will be on hold at any given time).
Select End call to end whichever call is active.
The call on hold will remain in the hold queue
and can be continued by pressing the right con­
trol button > Resume.
Merge to conference: Up to five callers and one
caller on hold can be added to a conference (de­
pending on the network service). To set up a fur- Telephone
ther call, place all the members of an existing
conference on hold by pressing the right control
button > Hold. Press the left control button. Se­
lect and confirm Call list/Directory/Favourites >
entry in List. You can add the contact you have
called to the conference using the right control
button > Merge to conference. Select Resume to
retrieve all participants in an existing conference
from the hold queue.
Connection manager: ¢ page 187, Connection
manager.
Telephone settings: ¢ page 134, Telephone set­
tings .
@ Note
- If you are using the handsfree profile
(Handsfree), the option Call waiting must
be activated on your mobile phone for you
to be made aware of incoming calls during a
conversation.
- For further information, contact your mo­
bile network service provider or refer to the
operating instructions for your mobile
phone.
- The display for the incoming call may re­
main visible for several seconds afterwards;
this depends on the type of mobile phone
you are using. Should you use the function
Replace or Ignore, it is possible that the
current call will be ended.
Favourites
Applies to vehicles: with telephone
In addition to the mailbox number, you can store
up to 50 contacts in the List of favourites, in any
order. .,. Sele
ct:
!TEL! button > left control button.
To store an existing telephone number as a fa­
vourite: Select and confirm Call list/Directory.
Select and confirm a contact in the list and
choose a telephone number. Select: right control
button > Store as favourite. Enter a name for the
favourite or accept the suggestion. Select and
confirm Store.
129