2014 AUDI R8 SPYDER coolant

WARNINGS. The engine compartment of any
vehicle is a hazardous area!
c::> &.
A WARNING
To help avoid injury, before you check any­
thing under the engine compartment lid:
- Switch off the engine.
- Remove the ignition key.
- Apply the parking brake.
- Move selector lever of S tronic to "N"
(Neutral); put manual transmission in
Neutral.
- Always let the engine cool down. Hot
components will burn skin on contact.
- To reduce the risk of being burned, never
open the engine compartment lid if you
see or hear steam or coolant escaping
from the engine compartment. Wait un­
til no steam or coolant can be seen or heard before carefully opening the en­
gine compartment lid .
- Keep children away from the engine com­
partment .
-Never spill fluids on hot engine compo­
nents. They can cause a fire.
- Never open the coolant reservoir cap when the engine is still warm. The cool­ant system is pressurized and hot cool­
ant could spray out.
- Protect your face, hands and arm from
steam or hot engine coolant by placing a
thick rag over the cap when you open the
coolant reservoir .
- Do not remove the engine cover under
any circumstances. This increases the
risk of burns.
- If work on the fuel system or the electri­
cal system is necessary:
- Always disconnect the battery.
- Never smoke or work near heaters or
open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch:
Checking and filling 173
- Ignition cables
- Other components of the high voltage electronic ignition system.
- If you must perform a check or repair
with the engine running:
- First, fully apply the parking brake,
move selector lever of S tronic to "N"
(Neutral); put manual transmission in
Neutral.
- Always use extreme caution to prevent
clothing, jewelry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts. Tie back hair before
starting, and wear no clothing that will hang or droop into the engine.
- Minimize exposure to emission and chemical hazards
c::> .&. .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition, certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm.
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
@ Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam­
age to vehicle systems will occur.
@ For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly. If
you see spots from oil or other vehicle
IJI>
•
•

With S tronic transmission:
(!) Powe r steeri ng fluid rese rvoir
(~ ) ... .. ................ . . 149
@ Engine oi l filler cap ("1::r.) with
engine oil dipstick, ........ .. 180, 179
A WARNING
Before you ch eck a nything in the engine
compartment, always read and heed all
WARNINGS
~ A in Working in the engine
compartment on page 173.
@ Tips
The coolant expansion tank is located un­
der the convert ible top storage bay lid
~page 183.
Engine oil
Engine oil specifications (8-cyl.-engine )
The engine in your Audi needs the right kind
of oil.
-
The engine in your Audi is a soph istica ted
powerp lant tha t was b uilt to exacting specifi­
cations . This engine needs the r ight kind of
engine oi l that meets specifications regarding
qua lity and viscosity so that it can run
smoothly and reliably. Choos ing the right oi l
and changing oil within the time and mileage intervals printed in your veh icle's Warranty
&
Ma intenance book let matters a lot more to­
day than it d id yea rs ago. A udi has developed
a special quality standa rd for engine oil that
will he lp assure tha t your veh icle's eng ine will
get the lubrica tion it needs for prope r opera­
tion.
M odern eng ine lub rication has taken a quan­
t um leap in the last few yea rs. Ma ny synthetic
oils availa ble today provide be tter eng ine lu­
b rica tion that can outlast traditional pe trole ­
um-based o ils, making them a smart choice
for use throughout the life of your A udi.
Whether yo u use syn thetic or petroleum­
based engine oil, the oil that yo u use must
conform to Audi's oil qua lity standard VW S02
00 to help keep your vehicle's engine running
Checkin g and fillin g 175
smooth ly and he lp prevent the format ion of
harmful deposits, sometimes ca lled "s ludge,"
that over time can lead to expensive repairs.
At the time of prin ting, engine oils ava ilab le in
t h e U.S . and Canada that meet the exacting
specifications of Audi oi l standard VW 502 00
are synt het ic eng ine oi ls . Th is does not mean,
however, that every synthetic engine oil will
meet Audi o il standard VW 502 00. So always
be sure that you use an approved oil.
To he lp prevent the formation of harmfu l de­
pos its use on ly oil with the following specifi­
cations pr inted on the o il conta iner:
Audi oil standard VW 502 00
Oil containe r labels m ay car ry the s peci fica­
t ion sing ly or in combina tion wi th othe r desig ­
na tions and oil quality s tanda rds .
Viscosity
Engine o ils are graded accord ing to thei r vis­
cosity. The p roper viscos ity grade oil fo r yo ur
engine depends o n climactic or seasona l con­
ditions where yo u drive. You must use oil w it h
a v isco sity g rade of SA E 5W-30 all temper a­
tu re ranges fo r norma l d riving condi tions.
Because eng ine o il that meets the Audi oil
sta ndard may not be availab le everyw here
whe n you need i t, we strong ly reco mmend
t h at you a lways carry wit h you an ex tra quart
( li ter) of oil that exp ress ly con forms to the
VW 502 00, in case you have to top
off the oil
whi le on the road.
Only if the level of the o il is at or be low the
minimum ma rk on the oi l dipstick -and no oil
that expressly conforms to Audi oi l VW 502
00 is ava ilab le -may you top
off with a h igh
quality eng ine o il, preferab ly synthetic-based,
that meets ACEA A3 or API SM specifications. However, duri ng the entire time between oi l
c h ange in tervals, neve r top
off w ith more tha n
a total of 1 qt/lite r engine oil that does not
confo rm to Aud i oil spec ifi cat ion VW 50 2 00.
For more information abo ut eng ine oi l that
has been approved for your veh icle, please
contact e ither you r autho rized Aud i dea le r o r ..,.
•
•

CD Note
-The oil leve l mus t not be ab ove range
¢ page 179 , fig. 141 G) -danger of con­
verter or engine damage! Contact an au­
thorized Audi dealer to draw off oil, if necessary .
- Audi does not recommend the use of oil
additives. They may damage the engine
and adversely affect your New Vehicle
Warranty .
@ For the sake of the environment
-Under no circumstances can the o il come
i n contact with the sewage network or
the soil.
- Observe and follow lega l regu lations
when d isposing of empty oil containers.
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro­ tects the engine from freezing in the winter.
The cooling system is sea led and generally re­
q ui res lit tle at ten tion.
The cooling system has been filled at the fac­
tory with a pe rma nent coolant which does not
need to be changed. The coolant consists of a
mix ture o f wa ter and the m anu fa ctu rer 's g ly ­
col -based coolant addit ive Gl3 antifreeze
with anticorrosion additives (50% for USA mod els; 60% for Canadian models) . This mix ­
ture both assures the necessary frost protec ­
tion and protects metal components i n the
engine's cooling system from corrosion and
scaling .
It also raises the bo iling po int of the
coolant.
Do not reduce the concentration of the coo l­
ant in the summer by adding plain water.
The
proportion of coolant addit ive must b e at
lea st 50% but not more than 60 %
to main­
tain antifree ze protection and cooling efficie n­
cy.
If t he cool ant frost pro tect io n is too low,
the coo lant cou ld freeze and damage the veh i­
cle heating and engine cooling system.
Checkin g and fillin g 181
For year -round driving, antifreeze is added at
the factory for temperatures down to:
- -31°F(-35°C)USA
- -40 °F ( -40 °C) Canada.
.8, WARNING
Before you check anythi ng i n the engi ne
com partmen t, a lways re ad and heed al l
WA RNIN GS
q .&. in Working in the engine
compartment on page 173 .
-
CD Note
- Before wi nte r sets in, have the coo lant
checke d to see if the cool ant a ddi tive in
yo ur vehicle is sufficient to meet the cli ­
mate conditions . This is especia lly impor ­
tant if you live in a region where the win­
ter is extreme ly cold. I f necessary, in­
crease the proportion of coo lant add itive
to 60% .
- When adding coolant additive to your cooling system, remember :
- We re commend using o nly coola nt ad­
di tive G l2++ or Gl3 (check the l abe l)
for your vehi cle. This coolan t additive is
ava ila ble at autho rize d Aud i dea le rs .
Othe r ty pes of antifreeze can sig nifi­
cantly reduce corros ion protection. The
resu lting corrosion can cause a loss of
coolant and serio us engine damage.
- Do not add any type of rad iator leak seal ­
ant to yo ur vehicle 's engine coolant.
Add ing radiator repair flu id may adverse­
ly affect the f unction and performance of
your cooling system and co uld resu lt in
damage not covered by you r New Vehicl e
Li mited War ran ty.
•
•

182 Checking and filling
Checking the engine coolant level
Proceed carefully when checking the coolant.
Fig. 144 Convertible top: se rvice position
Fig. 145 Convert ible top sto rage bay: coo lant expan­
sion tank
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS c:::> &_ in Working in the engine compart­
ment on page 173
and park your vehicle on a
level surface.
The coolant expansion tank is located in the
right side of the convertible top storage bay
under the round metal cover
c:::> fig. 145. The
convertible top must be in the service position
to check the coolant leve l
c:::> fig. 144.
Bringing the closed convertible top into
the service position
.. Switch the ignition on .
.. Pull and hold the convertible top switch .
.. Press and hold the rear window switch too
until the convertib le top moves into the
service position
c:::> fig. 144.
Bringing the open convertible to into the
service position
.. Switch the ignition on.
.. Press and hold the convertible top switch. ..
Press and hold the rear window switch too
until the convertible top moves into the
service position
c:::> fig. 144.
Opening the coolant expansion tank cover
.. Stop the engine and allow it to cool.
.. Switch the ignition off .
.. Care fully remove the bolts in the cover@
using a screwdriver and remove the cover.
The coolant reservoir is located below
¢fig. 145.
Checking the engine coolant level
.. Place a rag or cloth on the cap of the coolant
expansion tank and turn the cap
carefully to
the left (counter-clockwise)
c:::> .&, .
.. Read the coolant leve l inside the coolant ex­
pansion tank¢
fig. 145. With a cold engine,
it must be above the "min" mark. With a hot
eng ine, it can be a little above the indicated
range.
To obtain an accurate reading, the engine must be switched off.
The expansion tank in your vehicle is equipped
with an electric coo lant level sensor
c:::> page 15. We still recommend you check the
coolant level from time to time .
Coolant loss
Coolant loss may indicate a leak in the cooling
system. In the event of coolant loss, the cool­
ing system should be inspected immediately
by your authorized Audi dealer. It is not
enough merely to add coolant.
In a
sealed system, losses can occur on ly if
the boiling point of the coo lant is exceeded as
a result of overheating .
A WARNING
-- The cooling system is under pressure. Do
notopenthecapofthecoolantexpan­
sion tank when the engine is hot. You
ris k be ing sca lded.
- The coolant additive, and therefore the
coo lant itself, is haza rdous to hea lth .
Keep the coolant additive in the original

container out of the reach of children. It
is a poison hazard.
@ Note
Do not add any type of radiator leak seal­
ant to your vehicle's engine coolant. Add­
ing radiator repair fluid may adversely af­
fect the function and performance of your
cooling system and could result in damage
not covered by your New Vehicle Lim ited
Warranty.
Adding coolant
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS q A in Working in the engine compart­
ment on pag e 173.
"'Add coolant .
"'Twist the cap on again
tightly.
"'Tighten the cap (D q page 182, fig. 145
again.
Replacement engine coolant must conform to
exact specifications
q page 181, Coolant .
We recommend using only coolant additive
G12++, G13 or in an emergency G12 +. Do
not
use a different additive. In an emergency use
plain water until you can get the correct addi­
tive and can restore the correct ratio. This
should be done as soon as possible.
If you have lost a considerable amount of
coolant, then you should add cold antifreeze
and cold water only when the engine is cold.
Always use
new engine coolant when refilling .
Do not fill coolant above the "max" mark. Ex­
cess coolant will be forced out through the
pressure relief valve in the cap when the en­
gine becomes hot.
A WARNING
- The cooling system is under pressure and
can get very hot. Reduce the risk of
scalding from hot coolant by following
these steps.
Checking and filling 183
- Turn off the engine and allow it to cool
down.
- Protect your face, hands and arms from
escaping fluid and steam by covering
the cap with a large, thick rag.
- Turn the cap slowly and very carefully
in a counter-clockwise direction while
applying light, downward pressure on
the top of the cap.
- To avoid being burned, do not spill an­
tifreeze or coolant on the exhaust sys­
tem or hot engine parts. Under certain
conditions, the ethylene glycol in en­
gine coolant can catch fire .
- Antifreeze is poisonous. Always store an ­
tifreeze in its original container and well
out of the reach of children.
- If you drain the coolant, it must be
caught and safely stored in a proper con­
tainer clearly marked "poison" .
Q) Note
- Coolant pollutes the environment and
could cause an engine fire . Ex cess cool­
ant will be forced out through the pres­
sure relief valve in the cap when the en­
gine becomes hot.
- If, in an emergency, only water can be
added, the correct ratio between water
and antifreeze
q page 181 must be re­
stored as soon as possible.
@ For the sake of the environment
Drained coolant should not be reused . Al­
ways dispose of used coolant while observ­
ing all environmental regulations.
Brake fluid
Have the brake fluid changed by an experi­
enced t echnician.
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too
high, corrosion in the brake system may result
afte r a period of time. The boiling point of the
brake fluid will also decrease considerably and
decrease braking performance. .,.. •
•

188 Checking and filling
cracked and weakened when the battery
froze.
- Charge the battery in a we ll ventilated
area. Keep away from open f lame or elec­
trical spark. Do not smoke. Hydrogen gas
generated by the battery is explosive.
- To reduce the danger of explosion, never
connect or disconnect charger cables
wh ile the charger is operating.
- Fast charg ing a battery is dangerous and
should only be attempted by a compe­
tent technicia n w ith the proper equip­
me nt.
- Battery acid that may spill during charg­
ing should be washed off with a solution
of warm water and baking soda to neu­
tralize the acid.
(D Note
Never use a fast charger as a booster to
start the engine. This will seriously dam­
age sensitive electronic components, such
as control units, relays, rad io, etc., as we ll
as t he battery charger.
(D Tips
- The vehicle battery must not be charged
with a standard small charger that p lugs
i nto the c igarette lighte r o r outlet.
- Only charge the battery through the con­
nect ions in the luggage compartment.
Windshield washer
container
Fig. 148 Luggage compartment: Wind shie ld washer
fl uid reser voir
T he washer fluid container is marked with the
symbol
O on its cap ~page 174, fig. 136 .
,. Lift the fi ller cap tongue to add washer flu­
id. You can fil l the container to the top.
,. Press the cap back onto the filler neck after
fi lling the container .
You can find the reservo ir
c a p acit y in the table
in
~ page225
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
the washer jets. Always add a glass cleane r
solution (with frost protection in the winter).
(D Note
- Do not mix e ngine coolant ant ifreeze or
any other additives to fill up the w ind­
shield washer reservoir .
- Do not use g lass cleaners conta ining
pai nt so lvent; you risk damaging the
paint.

190 Tire s and wheel s
-Never mount used tires on yo ur vehicle if
yo u are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to sudden t ire failure
and loss of vehicle control.
- If you notice unusual vibration or if the
vehicle pulls to one side when driving, al­
ways stop as soon as it is safe to do so
and check the wheels and tires for dam­
age.
(D Note
Please note that summer and winter tires
are designed for the cond itions that are
Glossary of tire and loading terminology
Accessory weight
means the comb ined we ight (in excess of
those standard items which may be rep laced)
of au toma tic tra nsmission, power steer ing,
power brakes, power windows, power seats,
radio, and heater, to the extent that these
items are availab le as factory -installed equip­
ment (whether installed or not) .
Aspect ratio
means the ratio of the he ight to the w idth of
the tire in percent . Numbers of 55 or lower in­
dicate a low sidewall for improved steering re­
sponse and better overall handling on dry pavement .
Bead
means the part of the ti re that is made of
steel wires, wrapped or reinforced by ply cords
and that is shaped to fit the rim.
Bead s eparation
means a b reakdown of the bond between
components in the bead.
Cord
means the strands forming the plies in the
tire . typ
ica l in those seasons . Audi recommends
using winter tires during the winter
months . Low temperatures signif icant ly
decrease the e lasticity of summer tires,
which affects tract ion and brak ing ability.
If summer tires are used in very co ld tem­
peratures, cracks ca n form on the tread
bars, res ulting in permanent tire damage
that can cause loud driving no ise and un­
balan ced t ires. Audi is not responsible for
th is type of damage .
Cold tire inflation pre ssure
means the t ire p ressure recommended by the
vehicle manufacturer fo r a tire of a des ignated
s ize that has not bee n driven for more than a
coup le of miles (k ilometers) at low speeds in
the three hour period before the tire pressure
is measured or adjusted.
Curb weight
means the we ight of a motor ve hicle w ith
standard equipment including the max imum
capacity of fuel, oil, and coolant, air condi ­
tioning and additional weight of optiona l
equipment.
E x tra load tire
means a t ire designed to ope rate a t higher
loads and at highe r inflation p ressu res than
the corresponding standard tire. Extra load
tires my be identified as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Gross A xle Weight Rating ("GAWR ")
means the load -carry ing capacity of a s ingle
axle system , measured at the tire-ground in­
terfaces.
Gr oss Vehicle Weight Rating ("GVWR ")
means the maximum total loaded we ight of
t h e vehi cle. .,.

load limits are technically referred to as the
vehicle's
Gross Vehicle Weight Rating
("GVWR").
The "GVWR" includes the weight of the basic
vehicle, all factory installed accessories, a full
tank of fuel, oil, coolant and other fluids plus
maximum load. The maximum load includes
the number of passengers that the vehicle is intended to carry ("seating capacity") with an
assumed weight of 150 lbs. (68 kg) for each
passenger at a designated seating position
and the total weight of any luggage in the ve­
hicle.
T he
Gross Axle Weight Rating (" GAWR") is
the maximum load that can be applied at each
of the vehicle's two axles .
The Gross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance sticker label located on the
driver 's side B-pillar . Your Audi has 2 seating
positions. Each seating position has a safety
belt ¢
page 103, Safety belts.
The fact that there is an upper limit to your
vehicle 's Gross Vehicle Weight Rating means
that the total weight of whatever is being car­
ried in the vehicle is limited. The more passen­
gers in the vehicle or passengers who are
heavier than the standard weights assumed
mean that less weight can be carried as lug­
gage.
The tire pressure label on your Audi also lists
the maximum combined weight of all of the
occupants and luggage or other cargo that
the vehicle can carry. For the location of the label
¢page 193, fig. 149 .
A WARNING
Overloading a vehicle can cause loss of ve­
hicle control, a crash or other accident, se ­
rious personal injury, and even death .
- Carrying more weight than your vehicle
was designed to carry will prevent the
vehicle from handling properly and in­
crease the risk of the loss of vehicle con­
trol.
Tires and wheels 197
- The brakes on a vehicle that has been
overloaded may not be able to stop the
vehicle within a safe distance .
- Tires on a vehicle that has been overload­
ed can fail suddenly, including a blowout
and sudden deflation, causing loss of
control and a crash .
Determining correct load limit
Use the example below to cal­
culate the total weight of the passengers and luggage or oth­
er things that you plan to trans­
port so that you can make sure
that your vehicle will not be overloaded.
Steps for Determining
Correct Load Limit
1. Locate the statement "THE
COMBINED WEIGHT OF OC­
CUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS"on your vehi­
cle's placard (tire inflation pressure label)
¢ page 193,
fig. 149.
2. Determine the combined
weight of the driver and pas­sengers that will be riding in
your vehicle.
3. Subtract the combined
weight of the driver and pas­sengers from
"XXX" kilo-
grams or
"XXX" pounds .,.
•
•