2014 AUDI A8 remove seats

Pass-through with ski
sack
Preparing the pass-through
Applies to vehicles: with pass-through and ski sack
Long objects such as skis can be transported
in the ski sack.
Fig. 70 Rear bench seat: removing the protect ive cover
Fig. 71 Rear center armrest: attaching the protective
cover
~ Fold the rear center armrest and the cover
located behind it down.
~ Press the button to remove the protective
cover ¢
fig. 70.
~ To protect the front area of the center arm­
rest, position the cover as illustrated
¢
fig. 71 and press the suction cups down so
they adhere.
~ Remove the ski sack and unfold it.
Seats and storage 71
Loading and securing the ski sack
Applies to vehicles: with pass -through and ski sack
--~ --
·-- --· ----~-
Fig. 72 Luggage compartment: pass-through in th e
backrest
Fig. 73 Rear bench seat: sec uring the sk i sack
Loading
~ Fold the pass-through cover in the luggage
compartment down
c:;, fig. 72.
~ Slide the pointed end of the skis into the ski
sack first¢ ,&.. Th e front pa rt of the bind­
ings must be directly under the securing
strap on the ski sack@¢
fig. 73.
Securing
~ Insert the securing strap @ on the ski sack
into the center safety belt latch ©
c:> fig. 73.
~ Tighten the securing strap@.
Securing (vehicles with full-length center
console)
In the pass-through, two securing straps are
in the hooks located in the luggage compart­
ment .
~ Hook the hooks into the front tie-downs in
the luggage compartment .
~ Tighten the securing strap @in the rear.

7 2 Seats and storage
& WARNING
- The ski sack is intended only for the
transportation of skis and other light ob ­
jects . To reduce the risk of serious per­
sonal in jury, never t ransport heavy or
poin ted objects in the ski sa ck.
- When brak ing rapidly or during an acci­
dent, the load could be displaced and
ca use i njury to occupants.
- Sharp edges on the load must be cove red
for protect ion. Always fasten the belt
ti gh tly around the sac k and its contents
¢ fig . 73.
-For safety reasons, do not t ransport
more than two pairs of skis in the ski
sac k.
- You m ust sec ure the ski sack with t he
st rap a fter loading.
- Make su re a ll objects that you are trans­
porting in the pass-through are secured.
Otherwise they cou ld slide around during
sudden braking maneuvers and cause in ­
jury.
@ Tips
- Never stow the sk i sack away whe n it is
still wet or damp (for examp le, sn ow
melt ing from sk is) . Allow it to dry com­
plete ly before stowing it away .
- Position skis in the ski sack with the pointed ends facing t he front and ski
po les w ith the pointed ends facing the
rear.
Roof rack
Description and mounting locations
Additional cargo can be carried wi th a roof
luggage rack .
Fig . 74 Roo f ra ck attac hment po ints
.. Always read and follow the instr uct ions pro­
vided by the roof rack ma nufacturer when
i nstall ing the roof rack system .
If luggage or cargo is to be ca rried on the
roof, yo u mus t observe the follow ing:
- To enhance the vehicle 's streamlined design,
ra in gutters have been mo lded i nto t he roof .
I t is not poss ible to use normal roof ra cks.
O nl y install a roof ra ck specific ally designed
for your model AB . Contac t the nea re st Audi
dea ler for information on approved modular
roof racks for your v ehicle.
- On ly use roof racks approved for your vehi­
cl e. These approved roof racks are the basis
fo r a complete roof rack system. Addition al
a tta chmen ts or carr ier systems are needed
t o transpor t luggage and spor ts equipment.
We recommend using roof rack s from the
Aud i original accessories prog ram.
- When insta lling the roof rack, make sure it
is o nly mounted on the designated locations
on the roof~
fig. 74 .
-We recommend that you keep the i nstalla ­
tion instruct ions for your roof rack system
together w ith your Owner's literature in the
ve hicle.
When should the roof rack be removed?
- Before go ing through an au tomatic car wash
(it is best to ask the ca r wash operator for
adv ice)
...

7 4 Seats and storage
- Never exceed the maximum perm issible
load carrying capacity of the roof o f your
vehicle, the permissible axle weights and
the permissible total weight of your veh i­
cle
c::, page 289, Weights .
@ For the sake of the environment
As a result of the increased wind resist­
ance created by a roof rack, your vehicle is
using fuel unnecessarily. So remove the
roof rack after using it.
12-volt sockets
Applies to vehicles: 12-volt soc kets
Electrical accessories can be connected to ev­
ery 12-volt socket.
Fig. 75 Sect io n of the trim panel o f th e luggage com­
part ment : 12 -vol t socket
Fig. 76 Rear center conso le: 12-vo lt socket
... Open the socket cover c::, fig . 75 or c::, fig . 76 .
... Inse rt the p lug of the e lectrical device into
the socket.
There is an additional 12 vo lt socket in the
fro nt center console
c::> page 75, fig. 77.
The 12 volt sockets can be used for electr ica l
accessories . Th e power input must not exceed
120 watts . Before you purchase any accessories
, always
read and follow the information in
c::, page 294, Additional accessories and parts
replacemen t.
A WARNING
The sockets and the electrical accessories
connected to them operate only when the
i gnition is switched on . Incorrect usage
ca n lead to ser ious injuries or burns. To re­
duce the risk of inj uries, never leave ch il­
dren unattended in t he vehicle with the ve­
hicle key .
(D Note
To avoid damaging the socket, only use
plugs that fit p roperly.
- Never connect equ ipment that generates
elect rical current, such as a solar panel
or battery charger, to the 12 vol t socket .
T his could damage the vehicle 's elect ri­
cal sys tem .
- The 12 volt socket shou ld only be used
for a short per iod of t i me as a power
so urce for electrical equ ipment . Please
use the electrical sockets in the vehicle
when connecting equipment for longer periods.
@ Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained.

76 Seats and stor age
Addit ional storage
There are a variety of storage compartments
and fasteners in various places in the vehicle.
- Storage compartments in the doors
- Net in the front passenger footwell
- Eyeglasses compartment in the headliner (near the rearview mirror)
- Storage compartments under the center
armrests
- Compartments* on the back of the front
seat backrests
- Garment hooks over the rear doors
- Compartment in the center console with
pass-through)* (rear)
- Compartment behind the rear center arm­
rest (in vehicles without the pass-through*
or cooler*)
- Bag hooks in the luggage compartment
A WARNING
-When driving, do not leave any hard ob­
jects on the rear window shelf or allow
your pet to sit on the shelf. They could
become a hazard for vehicle occupants in
the event of sudden braking or a crash .
- Always remove objects from the instru­
ment panel. Any items not stored could
slide around inside the vehicle while driv­
ing or when accelerating or when apply­
ing the brakes or when driving around a
corner.
- When you are driving make sure that
anything you may have placed in the cen­
ter console or other storage locat ions
cannot fall out into the footwells. In case
of sudden braking you would not be able
to brake or accelerate.
- Any articles of clothing that you have
hung up must not interfere with the driv­
er's view. The coat hooks are designed
only for lightweight clothing. Never hang
any clothing with hard, pointed or heavy
objects in the pockets on the coat hooks.
During sudden braking or in an accident -
especially if the airbag is deployed - these objects could injure any passen­
gers
inside the vehicle.
- To reduce the risk of personal injury in an
accident or sudden stop, always keep the
glove compartment closed while driving.
- Read and follow all WARNINGS
c:> page 173, Important safety instruc­
tions on the side airbag system.
- Hang clothes in such a way that they do
not impair the driver's vision.
- The coat hooks must only be used for
lightweight clothing. Do not leave any
heavy or sharp edged objects in the pock­
ets which may interfere with the side cur­
tain airbag deployment and can cause personal injury in a crash.
- Do not use coat hangers for hanging clothing on the coat hooks as this can in­
terfere with proper deployment of the
side curta in airbags in an acc ident.
- Do not hang heavy objects on the coat
hooks, as they could cause personal in­
jury in a sudden stop.
@ Note
Objects located on the rear shelf that rub
against the rear window could damage the
heating wires for the rear window defog­
ger .
(D Tips
-A vent slot is located between the shelf
and the rear window. Do not block the
vent with any items you may place on the
rear window she lf.
- Do not place bulky items on the rear win­
dow shelf as they could restrict or block
the driver's vision in the rear view mirror.
Cooler
Introduction
App lies to vehicles: wit h coo ler
Please clean the cooler before using it for the
first time
c:> table on page 218 .
You can only switch on the cooler if ...

& WARNING
Damage to the front passenger seat can
prevent the front airbag from working
properly.
- Improper repair or disassembly of the
front passenger and driver seat will pre­
vent the Advanced Airbag System from
functioning properly.
- Repairs to the front passenger seat must
be performed by qualified and properly
trained workshop personnel.
- Never remove the front passenger or
driver seat from the vehicle.
- Never remove the upholstery from the
front passenger seat.
- Never disassemble or remove parts from
the seat or disconnect wires from it.
- Never carry sharp objects in your pockets
or place them on the seat. If the weight­
sensing mat in the passenger seat is
punctured it cannot work properly.
- Never carry things on your lap or carry
objects on the passenger seat. Such
items can increase the weight registered
by the weight-sensing mat and send the
wrong information to the airbag control
unit.
- Never store items under the front pas­
senger seat. Parts of the Advanced Air­
bag System under the passenger seat
could be damaged, preventing them and
the airbag system from working proper­
ly.
- Never place seat covers or replacement
upholstery that have not been specifical­
ly approved by Audi on the front seats.
- Seat covers can prevent the Advanced
Airbag System from recognizing child re­
straints or occupants on the front pas­
senger seat and prevent the side airbag
in the seat backrest from deploying prop­
erly.
- Never use cushions, pillows, blankets or
similar items on the front passenger
seat. The additional padding will prevent
the weight-sensing mat in the seat from
accurately registering the child restraint
-
Airbag system 161
or person on the seat and prevent the
Advanced Airbag System from function­
ing properly.
- If you must use a child restraint on the
front passenger seat and the child re­
straint manufacturer's instructions re­
quire the use of a towel, foam cushion or
something else to properly position the
child restraint, make certain that the
PASSENGER AIR BAG OFF light comes
on and stays on whenever the child re­
straint is installed on the front passen­
ger seat.
- If the PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install child restraint in a rear seat­
ing position and have the airbag system
inspected by your Audi dealer.
How the Advanced Airbag System
components work together
The front Advanced Airbag System and the
side airbags supplement the protection of­
fered by the front three-point safety belts
with pretensioners and load limiters and the
adjustable head restraints to help reduce the
risk of injury in a wide range of accident and
crash situations. Be sure to read the impor­
tant information about safety and heed the
WARNINGS in this chapter.
Deployment of the Adv a need Airbag System
and the activation of the safety belt preten­
sioners depend on the deceleration measured by the crash sensors and registered by the
electronic control unit. The amount of infla­
tion of the front airbags can also be adapted
to the front seat position, depending on the
distance between the respective front seat
and the steering wheel or instrument panel as registered by sensors in the seats. Crash se­
verity depends on speed and deceleration as
well as the mass and stiffness of the vehicle
or object involved in the crash.
On the passenger side, regardless of safety
belt use, the airbag will be turned off if the
weight on the passenger seat is less than the
Iii>'
•
•

192 Child Safe ty
and prope r use of the lower anchorages
or safety belts in your vehicle.
- Never secure or attach any luggage or
other items to the
LATCH lower ancho­
rages .
- Always read and heed the important in­
format ion about child restra ints in this
chapter and WARNINGS
¢ page 177,
Child Safety .
Guidance fixtures for lower anchorages
Special guidance fixtures increase the conven­
ience of the lower anchorages and are availa­
ble from your au thori zed Audi dealer .
Fig . 183 Ou ter rea r seat s: in sta lling th e guid ance fix·
tu res
Fi g. 184 Clos e-up : fitting t he guidanc e fixt ure over th e
l ower anch orage b racke t
The lower anchorage attachment points a re
located on the rear seats between the seat­
back and the seat cushion . Special guidance
fixtures increase the conven ience of the lower
ancho rages and help protect the seat mater ial
from possib le damage when insta lling child
restraints .
Installing the guidance fixtures
"" Push down on the seat cushion so that the
lower anchorages are visible. ""Ho
ld the guida nce fixture with the part
number facing downward and push it in the
d irection of the arrow onto the ancho rage
¢ fig. 184 .
""Make sure that each of the two guidance fix­
tures per seat snaps into place .
Remo ving the gu idanc e fixtu res
""R emove the chi ld restra int according the
child restraint manufacturer's instructions.
""Push down on the seat cushion so that the
lower anchorages are v is ible.
"" Pull off the gu idance fixtures from the lower
anchorages .
"" Always remove the guidance fixtures and
keep them in a safe p lace when not in use.
You may find it easier to i nstall ch ild re­
stra ints equ ipped with hooks attached to
straps witho ut the g uidance fixtu res in place .
If this is the case, remove the gu idance fix­
tu res by pulling them off the anchorages.
However, the gu idance fixtures can help you
to locate the
LATCH anchorages.
_& WARNING
Improper use of tether anchorages or low­
er anchorages can cause ser ious personal
i njury in a crash.
- Always carefu lly follow the child re­
straint manufacturer's instr uctions for
proper insta llation and use of child re­
straint systems.
- Never use the
LATCH or tether anchorag­
es to attac h safety belts or other kinds of
occupant restra ints.
- Ch ild restra int tether attachments and
lower attachments are only designed to
secure a c hild restra int that has been
equ ipped to use these ancho rages .
- Tether anchorages and lower anc horages
are des igned to withstand only those
loads imposed by co rrec tly fitted child
restra ints . Un der no cir cumstan ces ca n
they be used safely fo r adult or child
safety belts or harnesses .

-Never mount more than one child re­
straint to a sing le tether or to a lower an­
chorage point. Attaching two child re­
straints to a single anchorage point can cause the anchorage to fail and cause se­
rious persona l injury in a crash.
(D Note
- Remove the guidance fixtures before
fo lding the rear seatback to prevent
damag ing the seat cushion .
- To attach the child restraint secure ly, the
seat must be moved to the farthest rear pos ition, the seat height set to the low­
est posit ion and the head restraint must
be adjusted to the vertical position
¢page 61.
-If you leave the guidance fixtu res instal ­
l ed for seve ral days, they could leave a
mark on the upholstery on the seat cush ­
i on and backrest in the area that the
guidance fixtures were insta lled . The up­
ho lstery would also be permanently
stretched around the guidance fixtures.
This applies especially to leather seats.
Installing a child restraint with LATCH
lower anchorages
Whenever you install a child restraint always
follow the child restraint manufacturer's in­
structions.
Fig . 18 5 Lower anchorages: proper mounting
Mounting
.,. Make su re the seatback of the rear seat
bench is in the upright position and sec urely
latched in place.
Child S afety 193
.,. Attach both hook -on connectors with the
spring catch release on the child safety seat
onto the LATCH lower anchorage so that the
connectors lock into place¢
fig. 185.
.,. Pull on the connector attachments to make
sure they are proper ly attached to the LATCH
lower anchorage .
.,. Pull straps tight fo llow ing the child restraint
manufac ture r's instruct ions .
Releasing
.,. Loosen the tension on the straps following
the child restra int manufacturer's inst ruc ­
tions.
.,. Depress the spring catches to release the
anchorage hooks from the lower ancho rag­
es.
Remember: Use tether straps to help keep the
c hi ld restra int firmly in place.
.&, WARNING
I mproper use of the LATCH system can i n­
crease the risk of serious pe rsonal injury
and death in a n accide nt.
- These an chors were deve loped on ly for
child safety seats using the " LA T CH" sys ­
tem .
- Never at tach o ther ch ild safety sea ts,
be lts or o ther objects to these anchors.
- Always ma ke s ure that you hear a click
when latch ing the sea t in place . If you do
not hear a click the seat is not sec ure and
could fly forward and hit the interior of
the vehicle, or be e jected from the vehi­
cle.
A WARNING
Improper installat ion of child restra ints
will increase the risk of injury in an acci­
dent.
- Always follow the child restraint system
manufacturer's instruct ions for proper
installation of the ch ild restra int system
and p roper use of tether straps as well as
the lower anchorages or safety belts in
your veh icle.
~