2014 AUDI A8 jack points

hold on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
Th e ve hicl e must be li~ed with the jack first
before the wheel can be removed.
F ig. 224 Sill p anels : m arkin gs
Fig. 225 Sill: posi tioning th e vehicle jack
.. Activate the vehicle jack mode in the MMI:
I CAR I function button > Car sy stem s control
button
> Se rvicing & ch ecks > Air susp .:
jack mod e
> On.
.. Engage the par kin g brake to prevent your
vehicle from roll ing un intentionally.
.,. Move the
se lector lev er to p osition P .
.. Find the marking (imprin t) on the sill that is
nearest the wheel that w ill be changed
c::> fig. 224 . Behind the marking, there is a
lifting point on the si ll for the vehicle jack.
.. Turn the
veh icle jack located under the lift­
ing point on the sill to raise the jack until its
arm @i:>
fig. 225 is located under the des ­
ignated plast ic mount
c::> _&.. c::>(D .
.. Align the jack so that its arm @ c::> fig. 225
engages in the designated lifting point in
the door sill and the movable base @ lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @.
What do I d o now ? 275
.. Wind the jack up fu rther unti l the flat tire
comes off the ground
c::> _A .
Position the veh icle jack o nly under the desig­
nated lifting points on the si ll
¢fig. 224.
There is exactly one locat ion for eac h wheel.
The jack must not be positioned at any other location
c::, .&, i:>0 .
An un stable surface under the jack can cause
the ve hicle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or simi lar s upport
under the jack. On
hard , sl ipper y su rf a ces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c::> .&, .
A WARNING
-You or your passengers co uld be in jured
while changing a wheel if you do not fo l­
low these safety pre cautions:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could s lip a nd cause an injury if it does not
have sufficient hold o n the vehicle.
- A soft or unstable surface under the
jack may cause the ve hicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessa ry,
use a stu rdy board under the jack.
- On hard, slippery su rface (such as t iles)
use a rubber mat or simi la r to prevent
the jack from slipping.
- To help prevent injury to yo urself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the veh icle and
well away from the road and traffic .
- Make sure jack position is correct, ad­
j ust as necessary and then cont inue to
raise the jack .
- Changes in temperature or load can af­
fect the height of the vehicle.

276 What do I do n ow ?
(D Note
Do not lift the vehicle by the si ll. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
{l) Tips
The vehicle jack mode switches off auto ­
mat ica lly at speeds above 10 km/h .
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fi g. 2 26 Cha ngin g a w hee l: u sing t he sc rewdrive r ha n·
dl e (w it h th e blade r emov ed) t o tu rn th e bolt s
F ig. 22 7 Chang ing a w hee l: a lig nm en t pi n inside t he
t op hole
After you have loosened a ll wheel bolts and
ra ised the ve hicle off the ground,
remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdri v­
er handle
to comp letely remove the top·
most wheel bo lt and set it as ide on a
clean
surface ¢fig . 226 .
.. Sc rew the th readed end of the alignment
pin
from t he tool kit hand-tight into t he
empty bolt hole¢
fig. 22 7 .
.. Then remove the other whee l bolts as de­
scribed above.
.. Take off the whee l leaving the a lignment pin
in the bo lt hole
c::> (D .
Putting on the spare wheel
.. Lift the spare whee l and carefu lly s lide it
over the alignment p in to g uide it in place
¢ (D .
.. Use the hexagonal socket i n the screwdriver
ha ndle to screw in and tighten a ll whee l
bolts
slightly .
.. Remove the alignment pin and inse rt and
tighten the rem aining wheel bol t slightly
like the res t .
.. Turn the jack hand le co unter-cloc kwise to
lower the vehicle until the jack is fully re­
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly
c;, page 2 74 . Tighten
them
crosswise, from one bolt to the (ap ­
proximately) opposite one, to keep the
wheel ce nte red.
(D Note
When remov ing or installing th e whe el,
th e rim cou ld hit the b rake ro to r and dam­
age the ro tor. W ork caref ully and have a
s eco nd pers on h elp yo u.
{i) Tips
N eve r use the he xagona l socket in the han­
d le of t he s crewdr iver to lo ose n or t igh ten
t he wheel bo lts .
- P ull the revers ible blade from the screw­
dr iver be fore y ou use the hexagon al
s o ck et in t he han dle to tur n t he w heel
bolts.
- W he n m oun tin g ti res w ith
unidirectional
tread design
make sure t he tre ad pat­
t er n is poin ted t he righ t way
c;, page277.
- Th e wheel bolts shou ld be clean and easy
to t urn. Check for dirt an d corrosion on
the mating surfaces of both the w heel

@ Tips
Check carefully to make sure the hook-up
is secure before moving the car up the flat­
bed truck ramp .
Vehicle transport
Whenever you hov e your vehicle transported,
be sure to note the following :
(D Note
Mount the tie-down chains/cables over the
running surface (circumference) of the
tires. Never secure the vehicle by the axle,
the suspension struts or the front or rear
towline eye . For technical reasons, the
pressure in the suspension struts may
change du ring the transport and this will
adve rsely affect vehicle handling.
Lifting vehicle
Lifting with workshop hoist and with
floor jack
The vehicle may onl y be li~ed at the lif ting
points illu stra ted.
Fi g. 2 40 Front l ift ing po int
Fig. 2 41 Rea r lifti ng poin t
• Read and heed WARNING Q ,&. .
Emergenc y situ ation s 287
• Activate the vehicle jack mode in the MMI :
!CAR I function button > Ca r system s control
button>
Ser vici ng & ch ecks > Air su sp. :
jack mo de > On .
• Locate lifting poin ts Q fig . 240 and
¢ fig . 241 .
• Adjust lifting arms of wo rkshop hoist o r
floor jack to match veh icle lifting points.
• Insert a rubber pad be tween the floo r jack/
workshop hoist and the lift ing po ints .
The vehicle jack mode must be activated so
that the automat ic adjustment of the Adap­
tive Ai r Suspens ion does not make it more dif­
fic ult to raise the vehicle with the floor ja ck.
If you mu st l ift your vehicle with a fl oor jack
t o wo rk underneath , be sure the vehi cle i s
s af ely s upported on stand s intended for thi s
purpose.
Front lifting point
The lifting point is located on the floor pan re­
i nforcement about at the same leve l as the
jac k mounting point
c:> fig . 240 . Do not lift
t h e v ehi cle at the verti cal sill reinf orcement .
Rear lifting point
The lifting point is located o n the vert ical rein ­
forcement of the lower sill for the on-board
jack ¢
fig. 241 .
Lifting with vehicle jack
Refer to ¢ page 275.
&_ WARNING ,-~
-To reduce the risk of serious injury and
vehicle damage .
- Always lift the vehicle only at the spe­
c ia l workshop ho ist and floor jack lift
points illustrated
c:> fig . 240 and
c:> fig. 241 .
- Failure to lift the vehicle at these
po ints could cause the vehicle to tilt or
fall from a lift if there is a change in ve­
hicle weight distribution and balance .
This might happen, for example, when h eavy components such as the eng ine
block or transmission are removed.

288 Emergency situations
- When removing heavy components like
these, ancho r vehicle to ho ist o r add cor­
responding weig hts to ma inta in the cen ­
ter of g ravity. Othe rwise, the vehicle
m ight tilt o r slip off t he hoist, causi ng
serious p erson al inju ry .
@ Note
- Be awa re of the following points befo re
li fting the vehicle:
- The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing , the
front or rear axle or the body side membe rs. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the veh icle weight does not
exceed the permissible lifting capacity
of the hoist .
-Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.