IAUTO I Switching automatic mode on
Automatic mode mainta ins a constant tem
perature inside the vehicle. Air temperature,
airflow and air distribution are controlled au
tomatically.
Adjusting the temperature
Temperatu res between 60 °F (+16 °C) and
84 °F ( +28 °C) can be set. O uts ide of this
range,
lo or hi wi ll appear in the climate con
trol system disp lay. At both of these settings,
the climate control system runs continuously
at maximum cooling or heating power. There
is no temperature regu lation.
~ Adjusting the airflow
You can adjust the airf low manually to suit
your needs . To have the airf low regulated au
tomatically, press the
I AUTO j button.
li!J Adjusting the air distribution
You can manually se lect the vents where the
air will flow. To have the air distribution regu
lated automatically, press the
IAUTOI button .
~I~* Adjusting seat heating/
ventilation*
Pressing the button switches the seat heat
ing/ventilation on at the highest setting ( level
3). The LEDs indicate the heating/ventilation
level. To reduce the heating/venti lation, press
the button again. To switch the seat heating/
ventilation off, press the button repeatedly
until the LED turns off.
After 10 minutes, the seat heating automati
cally switches from level 3 to level 2.
l
ed or cleared of condensation as quickly as
possible. The maximum amount of air flows
mainly from the vents below the windshield.
Recirculation mode switches off . The tempera
ture should be set to 72 °F (22 °C) or higher.
The
IAU TOI button switches the defroster off.
Warm and cold 73
liiii REAR ! Switching rear window heater
on/off
The rear window heater only operates when
the engine is running. It switches off auto matically after 10 to 20 minutes, depending
o n the outside temperature.
To prevent the rear window heater from
switching off automatically, press and ho ld
the ~ button for more than 2 seconds. This
remains stored until the ignition is switched
off .
I SYNC I Synchronization*
When synchronization is switched on, the
same settings are applied to both the driver
and front passenger, except for the seat heat
ing/ventilation*. The rear zone is also
synchronized. Synchronization switches off
when the settings for the front passenger s ide
o r r ear are adjusted.
You can also switch synchronization on by pressing and holding a dial. For example, if
you press and hold the dial on the front pas
senger side, the settings for that side are
transferred to the driver side. The same ap
plies to the rear.
Air vents
You can open or close the center and outer
vents in the cockpit and the vents in the rear
cente r console and door pillars using the
ridged thumbwheels. The levers adjust the di
rection of the airflow from the vents.
&_ WARNING
-=
-Do not use the recirc ulation for extended
periods of time . The windows could fog
up since no fresh air can enter the vehi
cle . If the windows fog up, press the air
recirculation button aga in immediately
to switch off the air recirculation func
tion or se lect defrost.
- Individuals w ith reduced sensitivity to
pa in or temperature cou ld deve lop burns
when using the seat heating function . To
red uce the risk of injur y, these individu-
als should not use seat heating. ..,.
Trailer towing Driving with a trailer
General information
Your Audi was designed primarily for passen
ger transportation .
If you plan to tow a tra iler, p lease remember
that the addit ional load will affect durab ility,
economy and performance .
Trailer towing not on ly places more stress on
the vehicle, it also calls for more concentra
tion from the driver.
F or this reason, a lways fo llow the operating
and driving instructions provided and use
common sense.
(D Note
If you are going to tow a trai ler, you must
ac tivate the trailer operation mode
c::> page 209, Operating instructions.
Technical requirements
Traile r hitch
Use a weig ht-carrying hitch conforming to the
gross trailer we ight. The hitch must be suita
b le for your veh icle and trailer and must be
mounted securely on t he ve hicle's chassis at a
technically sound location . Use only a trail er
hi tch w ith a removab le ball moun t. A lways
check wi th t he tra ile r hi tch man ufa ctur er to
make sure that you are using the cor rect
h itch.
Do not us e a bumper hitch .
The hitch m ust be installed in such a way that
i t does not interfe re with the impac t-absorb
i ng bumper syst em. No mod ificat ions should
b e made to the vehi cle e xhaus t and br ake sys
tems . From t ime to time, check th at a ll hitc h
mo unt ing bo lts rem ain securely fas tened.
When you are not towing a trail er, remove the
tra ile r hi tch ball moun t. T h is prevents the
hi tch from causing damage sho uld your ve hi
cle be str uck from behind~ .&.
Trailer towin g 209
Trailer brakes
If your trailer is equippe d wi th a bra king sys
tem, check to be s ure that i t conforms to all
regulations .
T he trailer hyd ra u lic bra ke sys tem mus t not be
d irec tly connec ted to the vehicle's hydraulic
brake system .
Safety chains
Always use safety chains be tween your ve hicle
and t he tra ile r.
Trailer lights
Trai ler lights must meet all reg ulations. Be
su re to c heck with your Audi dea ler for correct
wir ing, switches and relays .
Mirrors
If you a re unable to see the traffic behind you
u sing the regula r outside mirrors, then you
must insta ll extended mir rors. It is important
t h at you
always have clea r vis io n to the rear.
_&. WARNING
-
Afte r removi ng the trailer hitch , do no t
s tor e i t in yo ur v ehicl e. In case of sudden
b raki ng, the hi tch co uld fly forwar d and in
j ur e you o r yo ur pass enge rs.
Operating instructions
Maximum trailer weight
A tra ile r fo r you r vehi cle is l imited to a typi cal
cla ss 1 o r class 2 tr ailer.
Trailer load distribution
Be sure the load in the tra ile r is held secure ly
in place to p revent it from shift ing fo rward,
ba ckward or sideways.
Never allow a passenger to ride in a trailer
c::> .& in Driving instructions on page 211 .
Engine cooling sy stem
Towing a t railer ma kes the engine wor k hard
er . It is impo rtant that the cooling system's
performance is up to the additional load.
•
•
210 Trailer towing
Make sure that the cooling system has eno ugh
fluid .
Tire p res sure
When tow ing a trai le r, inflate the t ires of your
vehi cle to the co ld tire pressure listed under
"Full load" on the label located on the driver's
side B-pillar (visible when the door is open) .
Inflate trailer t ires to trai ler and tire manufac
turers' specifications.
Lights
Chec k to make s ure both veh icle and trailer
lights are working properly.
Safety chains
Be sure tra iler safety cha ins are properly con
nected from the trailer to the hitch on the ve
h icle. Leave enough slack in the chains to per
mit turn ing corners . When you install safety
cha ins, make su re they wi ll not drag on the
road when yo u are driving.
The chains shou ld cross under the tra iler
tongue to prevent it from dropping in case of
separation from the hitch.
Adjusting the Audi drive select
Make sure the vehicle is on a level su rface be
for e
hitching up the tra ile r and b efor e adjust
ing the tongue weight. The vehicle must be in
auto or comfort dr iving mode and no t raised
qpage 102, q(D _
Make sure that the vehicle is lowered. In Info
tainment , se lect:
ICARI f u nction button> Low
e r
control b utton .
I f you m ust dr ive under poor road co ndit ions,
you can raise the veh icle
aft er coup ling the
tra iler or
after adjusting the tong ue weig ht
q page 104.
-Changes in tempe ratu re or load can af
fect the heig ht of the veh icle.
- Always se lect
auto or comfort mode.
Otherwise, the tongue load spec ified for
your vehicle will no longer be applicable.
Driving instructions
Driving with a trailer always requires extra
care and consideration .
To obtain the best possible handling of vehicle
and trailer, please note the fo llow ing:
.,. Do not tow a loaded t railer when yo ur car it
self is not loaded.
.,. Be especially careful when passing other
veh icles.
.,. Observe speed limits .
.,. Do not dr ive at the max imum permissib le
speed.
.,. Always app ly brakes early .
.,. Mon itor the tempe ratu re ga uge.
Weight distribut ion
T owing a loaded trailer with an empty car re
su lts in a highly unstable distribution of
we ight. If this cannot be avoided, drive at very
low speeds on ly to avoid t he risk of losing
steering con tro l.
A "ba lanced " rig is easier to ope rate and con
t ro l. This means that the tow vehicle should
be loaded to the extent possible and permissi
ble , while keep ing the trai ler as light as possi
ble under the c ircumstances . Whenever poss i
ble , transfer some cargo to the luggage com
partment of the tow veh icle while observing
tong ue load requirements and vehicle load ing
considerations.
Speed
The higher the speed, the more difficu lt it be
comes for the driver to control the rig . Do not
drive at the maximum permissib le speed. Re
duce your speed even more if load, weather or
wind conditions are unfavorable -particularly
whe n going downhill.
Red uce veh icle speed
immediately if the trail
er shows the slightest s ign of sway ing .
Do not
try to stop the s way ing b y accele rating .
Observe speed limits . In some a reas, speeds
for vehicles tow ing tra ilers are lower than for
regular veh icles . .,.
current list of oils (manufacturers, brand
names etc.) that conform to Audi oil standard
VW 502 00 (vehicles with gasoline engine) or
VW 507 00 (vehicles with diesel engine).
C hanging the engine oil
The engine oil and oil filter must be changed
according to the mileage (kilomete rs) and
time intervals specified in your vehicle's War
ranty
& Maintenance booklet. Do not exceed
these intervals -harmful deposits from old
engine oil can reduce engine performance and
can lead to expensive engine repairs .
Changing the oil at the recommended inter
vals is so very important because the lubricat
ing properties of oil decrease gradually during
normal vehicle use. If you are not sure when
you have your oil changed, ask your author
ized Audi Service Advisor .
Under some circumstances the engine oil
should even be changed more frequently .
Change oil more often if you drive mostly
short distances, operate the vehicle in dusty
areas or mostly under stop-and-go traffic con
ditions, or when you use your vehicle where
temperatures stay below freezing point for long periods.
Detergent addit ives in the oil will make fresh
oil look dark after the eng ine has been run
ning for a short time. This is normal and is not
a reason to change the oil more often than
recommended.
Damage or malfunctions due to lack of
maintenance
It is essential that you change your oil at the
recommended intervals using only engine oil
that complies with Audi oil standard
VW 502 00 (vehicles with gasoline engine) or
VW 507 00 (vehicles with diesel engine). Your
Limited New Vehicle Warranty does not cover
damage or malfunctions due to failure to fol
low recommended maintenance and use re
quirements as set forth in the Audi Owner's
Manual and Warranty
& Maintenance booklet.
Your dealer will have to deny warranty cover
age unless you present to the dealer proof in
Checking and filling 231
the form of Service or Repair Orders that all
scheduled maintenance was performed in a
timely manner.
Engine oil consumption
The engine in your vehicle depends on an ade
quate amount of oil to lubricate and cool all
of its moving parts.
In order to provide effective lubrication and
cooling of internal engine components, all in
ternal combustion engines consume a certain
amount of oil. Oil consumption varies from engine to engine and may change significantly
over the life of the engine. Typically, engines
with a specified break-in period (see ¢
page 204) consume more oil during the
break-in period than they consume after oil
consumption has stabilized.
Under normal conditions, the rate of oil con
sumption depends on the quality and viscosity
of the oil , the RPM (revolutions per minute) at
which the engine is operated, the ambient
temperature and road conditions . Further fac
tors are the amount of oil dilution from water
condensation or fuel residue and the oxida
tion level of the oil. As any engine is subject to
wear as mileage builds up, the oil consump
tion may increase over time until replacement
of worn components may become necessary .
With all these variables coming into play, no
standard rate of oil consumption can be es
tablished or specified. There is no alternative
to regular and frequent checking of the oil lev
el, see
Note .
If the yellow engine oil level warning symbol
in the instrument cluster
II! lights up, you
should check the oil level as soon as possible
¢
page 232. Top off the oil at your earliest
convenience
9 page 232.
.&, WARNING
Before you check anything in the engine
compartment, always read and heed all
WARNINGS ¢.&.
in Working in the engine
comportment on page 22
7.
-
•
•
234 Check ing and filling
@ For the sake of the environment
- Before changing your oil , first make sure
you know where you can properly dispose
of the used o il.
- Always dispose of used engine oil proper
l y. Do not dump it on garden soi l, wood
ed areas, into open streams or down
sewage dra ins.
- Recycle used engine oil by taking it to a
used engine oil collection facility in your
area, or contact a service station .
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro tects the engine from freezing in the winter.
The cooling system is sea led and generally re
q uir es little attention .
The cooling system has been filled at the fac
tory with a pe rmanent coolant which does not
need to be c hanged. The coolant consists of a
mixture of spec ia lly conditioned water and the
manufacturer 's glyco l-b ased coo lant add i-
tive G l3 antifreeze with ant icorrosion addi
tives (50% for USA models ; 60% for Canadian
mod els). This mixture both assures the nec es
sary frost protection and protects metal com ponents in the engine's cooling sys tem from
corrosion and scaling . It a lso raises the boil
ing point of the coolant .
Do not red uce the concentration o f the coo l
ant in the summer by adding plain water.
The
proportion of coolant add itive mu st be at
l e a st 50 % but not more than 60 %
to main
tain antifreez e protection and cooling efficien
cy . If the coolant frost prote ct ion is too low,
the coo lant cou ld freeze and damage the veh i
cle hea ting and eng ine cooling system.
For yea r-round d riving, antifreeze is added at
the fac to ry for temperatures down to:
-- 31°F( -35°C)USA
- -40 °F ( -40 °C) Canada. If
you must add coolant, use a mixture o f wa
ter and coolant additive . Mixing the coo lant
additive with distilled water is recommended.
A WARNING
-
Before you c heck anything in the engine
compartment, always read and heed a ll
WAR NINGS
c::, & in Working in the engine
compartment on page 22
7 .
(D Note
- Before winter sets in, have the coo lant
checked to see if the coolant additive in
your vehicle is sufficient to meet the cli mate conditions . This is especia lly impor
tan t if you live in a reg io n where the win
t er is ex treme ly cold. If ne cessa ry, i n
crease the pr opo rtion of coo lant add itive
t o 60%.
- Whe n adding coolant additive to yo ur
c oolin g sys tem, remembe r:
- We recommend using on ly coolant ad
d itive Gl2++ or Gl3 (check the label)
for your vehicle . This coolant additive is
ava ila ble at autho rized Aud i deale rs.
Other types of antifreeze ca n sig nifi
ca ntly reduce co rr os io n protection. The
r es ult ing co rrosion c an c ause a los s o f
coolant and serious engine damage.
- Do not add any type of rad iator leak seal
a n t to y our vehicle 's engine coolant.
Add ing radiator repai r fl uid may adverse
ly affect the function and performance of
your cooling system and co uld resu lt in
damage not covered by yo ur New Vehicle
Limited Warranty.
-
Checking the engine coolant level
The engine coolant level can be checked with
a quick glance .
Fig. 196 Eng ine compartment: cover on the coolant
expansion tank
Before you check anything in the engine com
partment,
alwa ys read and hee d all W ARN
ING S ¢.&. in Working in the engine compart
ment on page 22
7 .
.,. Park your vehicle on a level surface.
.,. Switch off the ignit ion.
.,. Read the engine coolant level from the cool
ant expansion tank¢
fig. 196, ¢ page 229 ,
fig. 193 .
With a cold engine, the coolant
level should be between the "min" and
"max" mar kings. When the engine is warm,
the leve l may be slightly above the "max"
marking.
The location of the coolant expansion tank
can be seen in the engine compartment illus
tration¢
page 229 .
To obtain an accurate read ing, the eng ine
must be switched off.
The expans ion tank in you r vehicle is equipped
with an electric coolant level sensor .
When the coolant level is too low, the warning
light in the Auto -Check System ¢
page 17 will
illum inate u ntil you add coolant a nd the level
has been restored to normal. Even though
there is an electric coolant level sensor, we
still recommend you check the coolan t leve l
from time to time.
Coolant loss
Coolant loss may indicate a leak in the cool ing
system. In the event of coolant loss, the cool-
Checkin g and fillin g 235
ing system should be inspected immediately
by your authorized Audi dealer . It is not
enough merely to add coolant.
In a
s ea led system, losses can occur on ly if
the boiling point of the coo lant is exceeded as
a result of overheating.
A WARNING
The cooling system is under pressure and
can get very hot. Reduce the risk of scald
ing from hot coolant by follow ing these
steps.
- Turn off the engine and allow it to cool
down.
- Protect your face, hands and arms from
escap ing f lu id and steam by cover ing the
cap with a la rge, th ick rag.
- Turn the cap slowly and very carefully in
a counter-clockwise d irect ion while ap
plyi ng light, downward pressure on the
top of the cap .
- To avo id being burned, do not sp ill anti
freeze or coolant on the exhaust system
or hot engine parts. Under certa in cond i
tions, the ethylene gly col in engine coo l
a nt can catch fire.
(D Note
Do not add any type of radiator leak sea L
ant to your veh icle's engine coo lant . Add
i ng radiato r repa ir flui d may adverse ly af
fect the funct io n and performa nce o f your
cooling system and could result in damage
not covered by your New Vehicle Limited
War ranty.
Adding coolant
Be very careful when adding engine coolant .
Before you che ck anyth ing in the eng ine com
partmen t,
alway s read and heed all WARN
INGS ¢.&_ in Working in the engine compart
ment on page
227 .
.,. Tur n off the engi ne.
.,. Let the engine cool down.
29 2 Index
Certification ...... ..... ... .. .. .... . 288
Changing a wheel .............. .. ... 266
Changing engine oi l ........ .. .. .. .. . 233
Chec king
Engine coolant leve l .... ... .. .. .... . 235
Tire pressure ... .. ..... ... .. .. .... . 249
Ch ild restra ints
Da nger of us ing ch ild restra ints in the
front seat . . . . . . . . . . . . . . . . . . . . . . . . 151
Where can I get additional information
about child restraints and their use? .. 193
Ch ild restra int system anchors ... ..... 189
Ch ild safety .. ..... ........ .. .. .... . 175
Convertible locking retractor . . . . . . . . . 186
Important safety instructions for using
ch ild safety seats ........... .. .. .. . 179
I mportant th ings to know when dr iving
with ch ildren . ............. .. .... . 175
Tether anchors .................... 192
Tether straps .. ... ...... ... .. .... . 192
Ch ild safety lock
Rear doors . .............. ... .. .... 40
Child safety seats .............. .... . 181
Boo ster se ats . . . . . . . . . . . . . . . . . . . . . 184
Convertible child seats ............. 182
Conve rtible locking retractor ......... 186
H ow do I properly install a child safety
seat in my vehicle? ...... .. .. .. .. .. . 179
I nfant sea ts ............. .. .. .. .. . 181
I nstall ing .... ............. ...... . 186
I nstalling a child restraint using the
L ATCH system .. .. ..... ... .. .. .... . 191
LATCH system ... .. .... ... .. .. .. .. . 19 1
Lower anchorages ............ .... . 190
Mount ing and releasing the anchorage
hook .. .. .. ... .... ...... ... ... .. . 191
Safety instructions . . . . . . . . . . . . . . . . . 179
Unused safety belts on the rear seat .. 181
C igarette lighter . . . . . . . . . . . . . . . . . . . . . 59
C le a ning .. .. .. . .......... .. .. .. .. . 213
Climate control Air vents ... ... .... ...... ... ... .. .. 71
Climate controls . . . . . . . . . . . . . . . . . . . . . 69
C limate con trol system
Supp lementary hea ter ... .. .. .. .... . . 74
Climate control (four-zone)
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 72 Climate control (three
-zone)
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 70
Clock .............................. 28
Closing Rear lid ........................... 38
Sl id ing/tilting sunroof ............. .. 42
Co ld tire inflation pressure ..... ... .. .. 247
Coming home ... .. ............. .... . 46
Compact spare tire .............. .... 265
Compartments . . . . . . . . . . . . . . . . . . . . . . 60
Compliance . . . . . . . . . . . . . . . . . . . . . . . . 288
Consumer Information . . . . . . . . . . 138, 285
Consumption (fuel) ... .......... .. .. . 25
Co ntacting NHTSA . ................ . 138
Controls Cleaning . ..... .. .. ... ..... ... .. .. 215
Co nvenience key . . . . . . . . . . . . . . . . . . . . . 36
Star ting the engine ............ .. .. . 76
Stopping the eng ine (START ENG IN E
STOP button) . . . . . . . . . . . . . . . . . . . . . . 77
Switching the ignition on .... ... .. .. . 76
Un locking and locking vehicle ......... 36
Converti ble child sa fe ty seats ..... .... 182
Co nvertib le locking retractor
Activati ng .... .... ............... . 188
Deact ivat ing . .. .. .......... ...... . 188
U si ng to secu re a child safety seat 1.86, 188
Coolant
refer to Engine coolant ............ . 234
Cooling mode (automatic climate control) 72
Cooling mode (climate control) ......... 70
Cruise contro l
Changi ng speed .. .. ... ....... ... .. . 85
Presett ing your speed ............... 85
Switching off .. .................... 85
Switch ing on . .. .. ... .......... .. .. . 84
Warning/ind icator lights ........ .. .. . 24
(upholder .. .. ... . .. .... .... ... .. .. . 60
C u rve light . ..... .. ... .. ..... .... . .. 102
Cylinder on demand System ........... 27
D
Data recorder ... ................... 196
Date disp lay . ..... .. .... .... ... .. .. . 28
Daytime run ning lights ........... .. .. . 44
302 Index
Windshield
C leaning ... ... . ...... ... .. .. .... .. 48
defrost ing (automatic climate cont ro l) . 73
defrost ing (climate control) . . . . . . . . . . 71
W indshield w ashe r system .. .. .. .... .. 48
Washer fluid leve l . . . . . . . . . . . . . . . . . . 22
Washer rese rvoir . ..... ... .. .. .... . 241
W indshield w ipe rs
C leaning ..... ........... .... .... .. 49
F o ld ing up ............ .. .... .. .. .. 49
I ndicator light . . . . . . . . . . . . . . . . . . . . . 22
Rep lacing windshie ld wiper blades ... . . 49
Switching on/off . ..... ... .. .. .... .. 48
W inte r oper ation
B at tery ...... ........... ........ . 238
Ca r washes .... . ...... ... .. .. .... . 213
Cooling system . .. ..... ... .. .. .... . 234
Defrosting windows (a utomatic cl imate
control) . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Defrosting windows (climate contro l) . . 71
Remov ing ice from windows .. .. .... . 215
Seat hea ting (automatic clima te control) 73
Seat heating (cl imate control) . . . . . . . . 7 1
St eer ing whee l heating .... .. .. .. .. . . 74
T ires .. .. .. ............. .. .. .. .. . 201
W inte r tires ... ... .... ..... .. .. .. .. . 258
All-w heel drive .......... ... .. .. ... 258
X
Xenon-Lig hts . . . . . . . . . . . . . . . . . . . 44, 2 7 5