2014.5 Citroen C4 lock

233
Removing a wheel
* position R   for   an   electronic   gearbox;   P for an
automatic   gearbox.
List of operations
F Remove   the   chromed   bolt   cover   from   each  o
f   the   bolts   using   the   tool   3   (according   to  
e

quipment).
F
 
F
it   the   security   socket   4 on the
wheelbrace


1   to   slacken   the   security   bolt.
F
 
S
lacken   the   other   bolts   using   the  
w

heelbrace 1  
o
n l y.
Parking the vehicle
Immobilise the vehicle where it does not block   traffic:   the   ground   must   be   level,  
s

table   and   non-slippery   ground.
Apply
  the   parking   brake   unless   it   has  
b

een   programmed   to   automatic   mode,  
s

witch   off   the   ignition   and   engage   first  
g

ear*   to   lock   the   wheels.
Check
  that   the   braking   warning   lamps  
i

n   the   instrument   panel   are   on   (not  
f

lashing).
The
  occupants   must   get   out   of   the  
v

ehicle   and   wait   where   they   are   safe.
If
  necessary,   place   a   chock   under   the  
w

heel   diagonally   opposite   the   wheel   to  
be c

hanged.
Never
  go   underneath   a   vehicle   raised  
u

sing   a   jack;   use   an   axle   stand.
11
Practical information

255
Charging the battery using
a battery charger
F Disconnect   the   battery   from   the   vehicle.
F  F ollow   the   instructions   for   use   provided   by  
t

he   manufacturer   of   the   charger.
F
 
C
onnect   the   battery   starting   with   the  
n

egative   terminal   (-).
F
 
C
heck   that   the   terminals   and   connectors  
a

re   clean.   If   they   are   covered  
w
ith
 s
ulphate
 (

whitish   or   greenish   deposit),   remove   them  
a

nd   clean   them.
Reinitialisation after
reconnection
after any reconnection of the battery, switch on
the  ignition   and   wait   at   least   one   minute   before  
s

tarting,   to   allow   time   for   the   initialisation   of   the  
e

lectronic   systems.
By
  referring   to   the   corresponding   sections,   you  
s

hould   set   or   initialise   the   following   systems  
y

ourself:
-
 
o
ne-touch   electric   windows,
-
 
t
ime   and   date,
-
 
a
udio   and   navigation   system   settings.
Check
  that   no   alert   message   or   warning   lamp  
c

omes   on   after   switching   on   the   ignition.
However,
  if   minor   problems   persist   after  
c

arrying   out   these   operations,   contact   a  
C

ITROËN   dealer   or   a   qualified   workshop.
Reconnecting the (+) cable
F Position  the   open   clamp   E of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   vertically   on   the   clamp   E to position
it
  correctly   on   the   battery.
F
 
L
ock   the   clamp   by   spreading   the  
p

ositioning   lug   and   then   lowering   the   tab   D.
Disconnecting the (+) cable
F Raise   the   locking   tab   D fully to release the
cable t erminal c lamp E.
D
o   not   apply   excessive   force   on   the  
t

ab   as   locking   will   not   be   possible   if   the  
c

lamp   is   not   positioned   correctly;   start  
t

he   procedure   again. With
  Stop   &   Start,   the   battery   does   not  
h

ave   to   be   disconnected   for   charging.
11
Practical information

259
Towing the vehicle
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F

r
aise the floor,
F
 
s
ecure   it   by   hooking   its   cord   on   the   hook  
o

n the rear parcel shelf
s
upport,
F
 
r
emove   the   towing   eye   from   the   holder.
Access to the tools General recommendations
In the following cases, you must always call o
n   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or  
f

ast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the  
g

earbox   into   neutral,   unlock   the  
 
s

teering,   or   release   the   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the  
g

round,
-
 
w
here   there   is   no   approved   towing   arm  
a

vailable...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed
 
or
 
for
 
towing
 
another
 
vehicle
 
using
 
a
 
removable
 
towing
 
eye.
Observe
 
the
 
legislation
 
in
 
force
 
in
 
your
 c
o unt r y.
Ensure
 
that
 
the
 
weight
 
of
 
the
 
towing
 
vehicle
 
i

s
 
higher
 
than
 
that
 
of
 
the
 
towed
 
vehicle.
The
 
driver
 
must
 
remain
 
at
 
the
 
wheel
 
of
 
the
 
t

owed
 
vehicle
 
and
 
must
 
have
 
a
 
valid
 
driving
 
l

icence.
When
 
towing
 
a
 
vehicle
 
with
 
all
 
four
 
wheels
 
o

n
 
the
 
ground,
 
always
 
use
 
an
 
approved
 
t

owing
 
arm;
 
rope
 
and
 
straps
 
are
 
prohibited.
The
 
towing
 
vehicle
 
must
 
move
 
off
 
gently.
When
 
towing
 
a
 
vehicle
 
with
 
the
 
engine
 
off,
 
t

here
 
is
 
no
 
longer
 
any
 
power
 
assistance
 
for
 
b

raking
 
or
 
steering.
11
Practical information

260
F On  the   front   bumper,   unclip   the   cover   by p
ressing   at   the   bottom.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   the   towing   bar.
Towing your vehicle
F On  the   rear   bumper,   unclip   the   cover  b y p
ressing   at   the   bottom.
F
 
S
crew   the   towing   eye   in   fully.
F
 
I
nstall   the   towing   bar.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.
Towing another vehicle
F Unlock   the   steering   by   turning   the   key  i
n   the   ignition   one   notch   and   release   the  
par

king
 b
rake.
F
 
S
witch   on   the   hazard   warning   lamps   on  
b

oth   vehicles.
F
 
M
ove   off   gently,   drive   slowly   and   for   a   short  
di

stance.F
 
P
lace   the   gear   lever   in   neutral  
(

position N on an electronic or
automatic   gearbox).
F

ailure to observe this instruction
could   result   in   damage   to  
c

ertain   components   (braking,  
t

ransmission...)   and   the   absence  
o

f   braking   assistance   the   next   time  
t

he   engine   is   started.
Practical information

263
Towbar with quickly detachable towball
Presentation
This towbar allows the towball to be fitted and removed   quickly   and   easily   without   the   use  
o

f   tools.   Installed   behind   the   rear   bumper,   the  
t

owbar   is   invisible   after   removing   the   towball  
a

nd   folding   the   trailer   harness   socket   carrier.
1.


Carrier
2.
 P

rotective   blanking   plug.
3.
 S

ecurity   ring.
4.
 F

olding   trailer   harness   socket.
5.
 D

etachable
 t
owball.
6.
 L

ocking   /   unlocking   wheel.
7.
 S

ecurity   key   lock.
8.
 L

ocking   wheel   protector.
9.
 Ba

ll
 pro
tector.
10.
 St

orage
 b
ag.A. Locked position
The locking wheel is not in contact with the towball   (gap   of   about   5   mm).
The
  green   mark   is   visible.
The
  lock   for   the   locking   wheel   is   facing  
r

earward.
B. Unlocked position
The locking wheel is in contact with the towball.
T hen   green   mark   is   hidden.
The
  lock   for   the   locking   wheel   is   facing   for ward.
Observe
  the   legislation   in   force   in   the  
c

ountry   in   which   you   are   driving.
For
  information   on   the   maximum   trailer  
w

eight   and   the   recommended   nose  
w

eight,   refer   to   the   "Technical   data"  
s

ection.
For
  information   on   safely   towing   a  
t

railer,   refer   to   the   "Towing   a   trailer"  
s

ection.
11
Practical information

264
Before each use
Check that the towball is correctly fitted by verifying the following points:
-  t he   towball   is   correctly   locked   in   place   (position   A),
-
 
t
he   security   key   lock   is   on   and   the   key   removed;   the   locking   wheel   can   no   longer   be  
ope

rated,
-
 
t
he   towball   must   no   longer   move   at   all   in   its   carrier;   try   to   shake   it   by   hand.
During use
Never unlock the device when a trailer or load carrier is fitted to the towball.
N ever   exceed   the   maximum   authorised   weight   for   the   vehicle   plus   trailer   (Gross   Train  
W

eight   -   GTW).
After use
For journeys made without a trailer or load carrier, the trailer harness socket must be folded away,   the   towball   removed   and    the   blanking   plug   inserted   in   the   carrier.   This   measure  
a

pplies   particularly   if   the   towball   could   hinder   visibility   of   the   number   plate   or   lighting.
Practical information

265
Fitting the towball
Remove the protective plug from the carrier and   check   the   condition   of   the   fixing   system.  
I

f necessary, clean the carrier with a brush or
clean
  cloth.
Take
  the   towball   from   the   storage   bag.
Remove
  the   protective   cover   from   the   ball   and  
t

he   protective   cap   from   the   locking   wheel.
Stow
  the   plug,   cover   and   cap   in   the   storage  
b

ag.
Check
  that   the   towball   is   unlocked   (position   B).
 
I

f   not,   insert   the   key   in   the   lock   and   turn   the   key  
a

nti-clockwise   to   unlock   the   mechanism.Take
  the   towball   in   both   hands;   insert   the   end  o
f   the   towball   into   the   carrier   by   lifting   it,   then,  
t

o   ensure   that   it   has   correctly   locked   in   place,  
p

ull   firmly   down   on   the   ball   end   of   the   towball.
The
  locking   wheel   automatically   turns   a   quarter  
o

f   a   turn   anti-clockwise,   making   a   perceptible  
c

lick;   take   care   to   keep   your   hands   clear.Check
  that   the   towball   has   correctly   locked   in  p
lace (position A).
Turn
  the   key   clockwise   to   lock   the   towball   fixing  
m

echanism.
Always
  remove   the   key   and   keep   it   in   a   safe  
p

lace.If
  the   key   cannot   be   turned   or   removed,  
t

his   means   that   the   towball   is   not   fitted  
c

orrectly;   start   the   procedure   again.
If
  one   of   the   locking   conditions   is   not  
m

et,   start   the   procedure   again.
In
  all   cases,   if   the   marking   remains  
r

ed,   do   not   use   the   towbar   and   contact  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop.
11
Practical information

266
Attach the trailer to the towball.attach the cable on the trailer to the security
ring
  located   on   the   carrier.
Lower
  the   trailer   harness   socket   carrier   by  
p

ulling   down   on   the   ring   visible   below   the  
b

u m p e r.
Remove
  the   protective   cover   from   the   socket  
a

nd   connect   the   trailer   wiring   harness.
Removing the towball
Disconnect the trailer harness from the socket on   the   carrier.
Detach
  the   cable   on   the   trailer   from   the   security  
r

ing   on   the   carrier.
Unhook
  the   trailer   from   the   towball.
Return the trailer harness connector carrier to
the
  folded   position. Insert
  the   key   into   the   lock.
Turn   the   key   anti-clockwise   to   unlock   the  
t

owball
 f
ixing
 m
echanism.
Practical information