2014.5 Citroen BERLINGO MULTISPACE RHD bonnet

DIESEL
Berlingo_2_VP_en_Chap07_Verification_ed02-2014
148
FuEL cut-OFF
In a serious collision, a mechanism automatically  prevents   fuel   from  
reaching

  the   engine.
The
  flashing   of   this   warning  
lamp

  is   accompanied   by   a  
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-
switch of

f the ignition (ST
o
P position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
dIESEL PrIMInG PuMP
If you should run out of fuel, it is
necessary  to   prime   the   fuel   circuit:
-
 
fill
  the   fuel   tank   with   at   least   five  
litres of

d iesel,
-
 
squeeze
  and   release   the   manual  
priming

  pump,   under   the   bonnet  
under the protective cover

,
-

operate the starter until the engine
starts. Refer

  to   chapter   7:   "Under   the  
bonnet"

  section.
Fuel used for diesel
engines
The Diesel  engines  are  compatible  with  biofuels
  which   conform   to   current   and  
future European standards (

d iesel fuel
which
  complies   with   standard   EN   590  
mixed

  with   a   biofuel   which   complies  
with standard E

n 14214) available at
the
  pumps   (containing   up   to   7   %   Fatty  
Acid

  Methyl   Ester).
The B30 biofuel can be used in certain
d

iesel engines; however, this use
is
  subject   to   strict   application   of   the  
special servicing conditions indicated
in

  the   maintenance   and   warranty  
guide.

  Contact   a   CITROËN   dealer   or   a  
qualified

  workshop.
The use of any other type of (bio)
fuel
  (vegetable   or   animal   oils,   pure  
or

  diluted,   domestic   fuel...)   is   strictly  
prohibited

  (risk   of   damage   to   the  
engine

  and   fuel   system).
Fuel

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
168
cHAnGInG A BuLB
type A
All   glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
High pressure washing
Open the bonnet. T o   access   the   bulbs,  reach
  behind   the   headlamp   unit.
Carry out the operations in reverse
order
  to   refit   each   bulb   and   check   that  
the

  bonnet   is   closed   securely.type c
Halogen

  bulb:   release   the  
retaining

  spring   from   its  
housing.
type B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
Halogen
  bulbs   must   be   changed  with
  the   headlamp   off.   Wait   a   few  
minutes

  (risk   of   serious   burns).  
d
o not touch the bulb directly with your
fingers,
  use   lint-free   cloths.
It
  is   normal   for   condensation   to   form  
inside

  the   headlamps.   Regular   use   of  
the

  vehicle   eliminates   this   misting.The
  bulbs   must   be   changed   with  
the ignition of

f or with the battery
disconnected.   Wait   approximately  
3 minutes

  after   changing   the   bulb  
before

  reconnecting   the   battery.
Check   that   the   lamps   operate   correctly  
after

  each   operation.
When using this type of washing
on stubborn dirt, do not persist on
the   headlamps,   the   lamps   and   their  
edges

  to   avoid   damaging   their   coating  
and

  seals.
types of bulb
Various types of bulb are fitted to your vehicle.
 T o   remove   them:
type

d
Light

  emitting   diode  
(LED):

  for   replacement  
of

  the   daytime   running  
lamps,

  contact   a  
CITR

o Ë n dealer or a
qualified
  workshop.
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
173
cHAnGInG A FuSE
The fuseboxes are located:
-
in the lower dashboard on the left-
hand side (behind the cover),
-

 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
removing and fitting a fuse
Always replace a failed fuse with
a fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 network.
CITR
o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 
installation of accessories not
supplied

 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 
10 millia

mperes. Before replacing a fuse, the cause of
the
 
incident
 
must
 
be
 
identified
 
and
 
rectified.
●

 
Use

 
the
 
tweezer.
Changing a fuse
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
9 10Headlamp
  beam   motor,   parc   management   unit
10 30 Engine
  components
11 40 Spare
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse