2014.5 Citroen BERLINGO MULTISPACE RHD key

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
38
FuEL GAuGEcOOLA nt t EMPE r Atur E
the needle is positioned before the
red zone:   normal   operation.
In arduous conditions of use or hot
climatic
  conditions,   the   needle   may  
move

  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-  
stop
  immediately,   switch   off   the  
ignition.

 
The
  fan   may   continue   to  
operate

  for   a   certain   time,   up   to  
approximately

  10   minutes,
-
wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As   the   cooling   system   is   pressurised,  
follow this advice in order to avoid any
risk

  of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   on   the   expansion  bottle,
-

if necessary,  remove  the  cap  to  top  up.
If the needle remains in the red zone,
  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.
Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The
 
fuel
 
level
 
is
 
tested
 
each
 
time
 
the
 key
 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the
 
warning
 
lamp
 
comes
 
on
 
continuously

.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
47
StOP & StArt
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine StOP mode
The "E c O"   warning   lamp  
comes

  on   in   the   instrument  
panel and the engine goes
into

  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with the 6-speed electronic gear
control gearbox

, at a speed below
5
  mph   (8   km/h),   when   you   press  
the

  brake   pedal   or   put   the   gear  
lever into position

n .If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   the   automatic   gearbox  
system,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  the
  ignition   with   the   key.Special cases: S t
OP
mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"E c O"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
t

his operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
49
reactivation
Press the "EcO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "E c O
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
50
Good practice when stopping Good practice when starting
diesel pre-heating warning
lamp
If
  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.
d
oor or bonnet open
warning lamp
If this comes on, a door or the bonnet is   not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
StArt I n G A nd S tOPPI n G
running and accessories position.
T o   unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
S
t
OP
position:   steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Starting and stopping

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
96
Automatic switching on/off
The  front   courtesy   lamp   comes   on  
when

  the   key   is   removed   from   the  
ignition,

  when   the   vehicle   is   unlocked,  
when one of the front doors is opened
and for location of the vehicle using the
remote

  control.
It goes off gradually after the ignition
is switched on and when the vehicle is
locked. Front
  seats:   comes   on   when  
one of the front doors is
opened.These are switched on and of

f by
means   of   a   manual   switch,   with  
the

  ignition   on.
Rear
  seats:   comes   on   when  
one of the rear doors is
opened.
If

  the   doors   remain   open   for  
a

  few   minutes,   the   courtesy  
lamps

  go   off.
Permanently
  off.
Permanently
  on,   ignition   on.
Front courtesy lamp
cOurtESY LAMPS
rear courtesy lamp
Front individual reading lamps
Practical information

 119
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Front airbags
The front airbags are fitted in the centre of the steering wheel for the
driver and in the dashboard for the
front  passenger.
d

eployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front
  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
d
eactivationo
nly the passenger's front airbag can
be   deactivated:
-

with the ignition switched off
,
insert
  the   key   into   the   passenger's  
front airbag deactivation switch,
-


turn it to the of
f "OFF" position,
-
 
then
  remove   the   key,   keeping   the  
switch

  in   the   new   position.
The passenger's front
airbag
  warning   lamp   in   the  
instrument

  panel   is   on   while  
the

  airbag   is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rear-facing child seat, contact
a
  CITROËN   dealer   or   a   qualified  
workshop.
Front airbag fault
T
o ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rear-facing child seat on the
front
  passenger   seat.   Otherwise,   the  
child

 
would
 
risk
 
being
 
kille
d  
or
 
seriously
 
injured

  if   the   airbag   were   to   inflate.
r
eactivation
In the "OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the airbag switch to the

"O n "
position to re-activate the passenger's
front airbag and so ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, contact a
CITR

o Ë n dealer or a
qualified
  workshop   to   have  
the

  system   checked.
airbags
SaFETY
5

133
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
AdVIcE On cHILd SEAtS
At the rear, always leave sufficient space
  between   the   front   seat   and:
-

a "rearward facing" child seat,
-


the feet of a child seated in a
"forward

  facing"   child   seat.
For
  this,   move   the   front   seat   forward  
and, if necessary

, straighten its
backrest
  as   well.
The incorrect installation of a child seat
in
  a   vehicle   compromises   the   child's  
protection

  in   the   event   of   an   accident.
Check   that   there   is   no   seat   belt   or   seat  
belt

  buckle   under   the   child   seat,   as   this  
could

  destabilise   the   seat.
Remember   to   fasten   the   seat   belts   or  
the child seat harnesses

keeping the
slack relative to the child's body to a
minimum,   even   for   short   journeys.
For the installation of a child seat using
the seat belt, ensure that the seat belt
is well tensioned on the child seat
and that it is holding the child seat
firmly   against   the   vehicle's   seat.   If   the  
passenger

  seat   is   adjustable,   move   it  
forward

  if   necessary. For   the   optimum   installation   of   a  
"forward facing" child seat, ensure that
the

  back   of   the   child   seat   is   as   close   as  
possible

  to   the   backrest   of   the   vehicle's  
seat,

  or   in   contact   if   possible.
The   head   restraint   must   be   removed  
before installin

g a child seat with a
backrest   on   the   passenger   seat.
Ensure that the head restraint is
stowed or attached securely so that it
is not thrown around the vehicle in the
event   of   sharp   braking.
Refit   the   head   restraint   as   soon   as   the  
child

  seat   is   removed.children at the front
The legislation on carrying a child on
the
  front   passenger   seat   is   specific   to  
each

  country.   Refer   to   the   legislation   in  
force

  in   your   country.
d

eactivate the passenger's airbag
when a "rearward facing" child seat is
installed
  on   the   front   seat.
Otherwise,
  the   child   would   risk   being  
seriously

  injured   or   killed   if   the   airbag  
were

  deployed.
Installing a booster seat
The chest part of the seat belt must be positioned on the child's shoulder
without   touching   the   neck.
Ensure that the lap part of the seat belt
passes
  correctly   over   the   child's   thighs.
CITROËN
  recommends   the   use   of   a  
booster

  seat   which   has   a   back,   fitted  
with

  a   seat   belt   guide   at   shoulder   level.
As
  a   safety   precaution,   never   leave:
-
 
one
  or   more   children   alone   and  
unsupervised in a vehicle,
-

 
a
  child   or   an   animal   in   a   vehicle  
which is exposed to the sun, with
the windows closed,
-

 
the
  keys   within   reach   of   children  
inside

  the   vehicle.
To prevent accidental opening of the
doors,
  use   the   "Child   Lock".
Take
 
care
 
not
 
to
 
open
 
the
 
rear
 
windows
 
by

  more   than   one   third.
To
  protect   young   children   from   the   rays  
of

  the   sun,   fit   side   blinds   to   the   rear  
windows.
For an installation in row 3, put the
backrests

 
of
 
the
 
outer
 
and
 
centre
 seats in row 2 in the table position, or
remove
 
these
 
seats
 
in
 
row
 
2,
 
so
 
that
 
the child seat or the child's legs do not
touch

 
the
 
seats
 
in
 
row
 
2.
Child safety
SaFETY
5

134
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
cHILd LOcK
This prevents opening of the side
doors  from   the   inside.
Manual mode
a label indicates the location of the
child

  lock.
-
o pen fully past the point of
resistance.
-

T
ilt the lever, located on the rear
section
  of   the   door. Electric mode
With the ignition on, press this
button.  
The
  LED   comes   on.
 W

arning:   this   system   is  
independent of the central
locking

  control.
Always   remove   the   ignition   key  
when leaving the vehicle, even for
a

  short   time.
It   is   advisable   to   check   the   activation   of  
the

  child   lock   each   time   the   ignition   is  switched
  on.
In   the   event   of   a   serious   impact   the  electric
  child   lock   is   deactivated  
automatically

.
Child safety