2014.5 Citroen BERLINGO MULTISPACE RHD turn signal

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
35Warning lamp isindicatesSolution - action
S cr
emissions
control
system
(BlueH
d i
d

iesel) on when switching
on the ignition,
associated with the
Service
and engine
diagnostic
  system  
warning

  lamps,  
accompanied

  by   an  
audible signal and a
message

  indicating  
an

  emissions   fault.a fault with the SCR
emissions
  control   system.This alert disappears as soon as the
exhaust
  emissions   return   to   normal   levels.
+ on when switching
on the ignition,
associated with the
Service
and engine
diagnostic
  system  
warning

  lamps,  
accompanied

  by   an  
audible signal and a
message

  indicating  
the

  remaining   driving  
range.the

  remaining   driving   range  
is

  between   0   and   650   miles  
(0

  and   1   100   km).Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible   to avoid a
breakdown.
+ on when switching
on the ignition,
associated with the
Service
and engine
diagnostic
  system  
warning

  lamps,  
accompainied

  by   an  
audible signal and a
message

  indicating  
that starting is
prevented.the

  authorised   driving   limit  
has

  been   exceeded:   the  
starting

  prevention   system  
comes

  into   play.To be able to restart the engine, you must
contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
Instruments and controls
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
36Warning lamp isindicatesSolution - action
d

ipped beam
headlamps /
d

aytime
running lams on.a
  manual   selection   or  
automatic

  illumination   of  
headlamps.T

urn   the   ring   on   the   lighting   control   stalk   to   the  
second

  position.
illumination of the  dipped  beam  headlamps from
  the   time   the   ignition   is   switched   on: daytime

  running   lamps   (depending   on   the
 country

  in   which   the   vehicle   is   sold).
Chapter 4, "Steering mounted controls" section.
Main beam
headlamps pullin
g
 
of
 
the
 
stalk
 
towards
 
you. Pull

  the   stalk   to   return   to   dipped   beam  
headlamps.
d

irection
indicators flashing
 
with
 
audible

 
signal. a change of direction via
the
 
lighting
 
stalk. To
  the   Right:   control   to   be   pushed   upwards.
To
  the   Left:   control   to   be   pushed   downwards.
Front
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.
r

ear
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.   In   conditions   of  
normal

  visibility,   switch   them   off   to   avoid   breaking  
the

  law.   "This   lamp   is   a   dazzling   red."
Instruments and controls

62
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
Exceeding the programmed
speed
Pressing the accelerator pedal in order
to  exceed   the   programmed   speed  
will have no ef

fect unless you press
the pedal firmly beyond the point of
resistance.
The
  limiter   is   deactivated   temporarily  
and

  the   programmed   speed   flashes  
accompanied

  by   an   audible   signal.
To
  return   to   the   limiter   function,   reduce  
your

  speed   to   below   the   programmed  
speed.
Switching the function off
- Place the switch in position 0 or
switch off the ignition to switch the
system
  off.
The
  last   programmed   speed   remains   in  
the

  memory.
Operating fault
The programmed speed is cleared then   replaced   by   three   dashes.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
Good practice
Flashing of the speed
The speed flashes:
-
following forcing of the accelerator
point of resistance,
-

 
when
  the   limiter   cannot   prevent   an  
increase in the vehicle speed due
to

  the   profile   of   the   road   or   on   a  
steep descent,
-

 
in
  the   event   of   sharp   acceleration. In
  any   event,   the   speed   limiter   cannot  
replace the need to observe speed
limits,

  nor   can   it   replace   the   need   for  
vigilance

  on   the   part   of   the   driver.
Always   pay   attention   to   the   profile  
of the road and sharp acceleration
and

  stay   in   complete   control   of   your  vehicle.
T
o   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-
 
never
  place   one   mat   on   top   of  
another

.
Steering mounted controls

11 0
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
AntI-SLIP rEGuLAtIO n (AS r )
A nd d Y n AMI c S t
ABILI
t Y
c

O ntr OL ( d S c )
These systems are linked and complement  the  ABS.
The
 
ASR
  system   is   very   useful   for  
maintaining

  optimum   drive   and  
avoiding losses of control of the vehicle
on

  acceleration.
The
  system   optimises   drive   to   prevent  
the

  wheels   skidding,   by   acting   on   the  
brakes

  of   the   drive   wheels   and   on   the  
engine.

  It   also   allows   the   directional  
stability

  of   the   vehicle   to   be   improved  
on

  acceleration.
Use the
d SC to hold your course
without
  attempting   to   countersteer.
If there is a variation between the
trajectory
  followed   by   the   vehicle   and  
that

  required   by   the   driver,   the   DSC  
system

  automatically   acts   on   the  
engine

  and   the   brake   of   one   or   more  
wheels,

  in   order   to   put   the   vehicle   back  
on

  course.
deactivation
In certain exceptional conditions
(starting   the   vehicle   when   stuck   in   mud  
or

  snow,   or   on   loose   ground...),   it   could  
prove useful to deactivate the a

SR and
DSC
  systems   to   make   the   wheels   spin  
and

  regain   grip.
Operating fault
Good practice
The ASR/DSC   systems   offer   increased  safety
  during   normal   driving,   but  
should

  not   incite   the   driver   to   take   risks  
or

  to   drive   at   high   speed.
The
  operation   of   these   systems   is  
ensured

  if   the   recommendations  
of

  the   manufacturer   regarding  
the

  wheels   (tyres   and   rims),   the  
braking

  components,   the   electronic  
components

  and   the   fitting   and   repair  
procedures

  are   observed.
After
  an   impact,   have   these   systems  
checked

  by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Operation
The warning lamp flashes when operation of the a SR or
DSC
  is   triggered.
t

hey engage again:
-
 
automatically
  above   30   mph  
(50
 
km/h), When
  a   malfunction   of   the  systems
  occurs,   the   warning  
lamp

  and   the   LED   come   on,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen.
-


Press the button or turn
the dial to the

d SC o FF
position (depending on
model).
-
 
The

 
LED   comes   on:   the  
ASR
  and  
DSC

 
systems   no   longer   come   into  
play

. -
 
manually
  by   pressing   the  
button again or by turning
the dial to this position
(depending

  on   model).Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.
The

  warning   lamp   may   also   come   on   if  
the

  tyres   are   under-inflated.   Check   the  
pressure

  of   each   tyre.
driving safely

 119
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
Front airbags
The front airbags are fitted in the centre of the steering wheel for the
driver and in the dashboard for the
front  passenger.
d

eployment
They are deployed, except the
passenger's front airbag if it has been
deactivated, in the event of a serious
front
  impact   applied   to   all   or   part   of   the  
front

  impact   zone   A in the longitudinal
centreline of the vehicle on a horizontal
plane
  directed   from   the   front   towards  
the

  rear   of   the   vehicle.
The
  front   airbag   inflates   between   the  
front occupant of the vehicle and the
dashboard to cushion their forward
movement.
d
eactivationo
nly the passenger's front airbag can
be   deactivated:
-

with the ignition switched off
,
insert
  the   key   into   the   passenger's  
front airbag deactivation switch,
-


turn it to the of
f "OFF" position,
-
 
then
  remove   the   key,   keeping   the  
switch

  in   the   new   position.
The passenger's front
airbag
  warning   lamp   in   the  
instrument

  panel   is   on   while  
the

  airbag   is   deactivated.If
  the   two   airbag   warning   lamps  
are on continuously

, do not install
a rear-facing child seat, contact
a
  CITROËN   dealer   or   a   qualified  
workshop.
Front airbag fault
T
o ensure the safety of your child,
it is essential to deactivate the
passenger's front airbag when you
install a rear-facing child seat on the
front
  passenger   seat.   Otherwise,   the  
child

 
would
 
risk
 
being
 
kille
d  
or
 
seriously
 
injured

  if   the   airbag   were   to   inflate.
r
eactivation
In the "OFF" position, the passenger's
front airbag will not be deployed in the
event   of   an   impact.
As   soon   as   the   child   seat   is   removed,  
turn the airbag switch to the

"O n "
position to re-activate the passenger's
front airbag and so ensure the safety
of your passenger in the event of an
impact.
If   this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, contact a
CITR

o Ë n dealer or a
qualified
  workshop   to   have  
the

  system   checked.
airbags
SaFETY
5

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
152
In the event of a fault with
the the Scr emissions control
system
When switching on the ignition, the
URE
a , SERVICE and diagnostic
warning
  lamps   comes   on,   accompanied
 by an audible signal and the display of


a
  message   "Emissions   fault"   to   signal   a
 fault

  with   the   emissions   control   system.
If
  it   is   a   temporary   fault,   the   alert  
disappears once the exhaust gas
emissions

  return   to   normal.during an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
A  system   that   prevents   engine  starting
  is   activated   automatically  
from

  650   miles   (1   100   km)   after  
confirmation

  of   a   fault   with   the   SCR  
emissions

  control   system.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop   as   soon   as  
possible. In the event of the detection


of a fault
If   a   fault   with   the   SCR   system   is  
confirmed

  (after   30   miles   (50   km)  
covered

  with   the   permanent   display   of  
the

  message   signalling   a   fault),   when  
switching on the ignition, the SER

VICE
and
  engine   diagnostic   warning   lamps  
come

  on   and   the   UREA
 
warning   lamp  
flashes,

  accompanied   by   an   audible  
signal

  and   the   display   of   a   message  
(e.g.:

  "Emissions   fault:   Starting  
prevented

  in   150   miles")   indicating   the  
remaining

  range   express   in   miles   or  
kilometres.
While

  driving,   the   message   is  
displayed every 30 seconds while the
fault

  with   the   SCR   system   persists.
You should go to a CITR
o Ë n dealer
or
  a   qualified   workshop   as   soon   as  
possible.
o

therwise, you will not be able to
restart
  your   engine.
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
156
- obtain a bottle of adBlue®. After first
 
checking
 
the
 
use-by
 
date,  
read carefully the instructions on
use on the label before pouring
the contents of the bottle into your
vehicle's

a
dBlue
® tank.
Important
:
 
if
 
your   vehicle's
 
a

dBlue
® tank is completely 
empty
 
-
 
which   is   confirmed   by   the alert

 
messages   and   the   impossibility
 of

 
starting
 
the   engine,   you   must   add   at
 least

 
3.8
 
litres   (so   two   1.89   litre bottles). -
 
After
  emptying   the   bottle,   wipe  
away

  any   spillage   around   the   tank  
filler

  using   a   damp   cloth.
If any additive is split or splashed,
wash   immediately   with   cold   water  
or

  wipe   with   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.
-  
Refit
  the   blue   cap   to   the   tank   and  
turn

  it   a   6
th of a turn clockwise, to its stop.
-
 
Close

 
the
 
filler   flap.
n
ever dispose of
a
dBlue
® additive
bottles
 
in
 
the
 
household
 
waste.  
Place

 
them
 
in
 
a
 
special
 
container  
provided

 
this
 
purpose
 
or
 
take
 
them   to  
your

 
dealer.
Important:
 
in the event of a top-
up after a breakdown because
of a lack of additive, signalled
by
 
the
 
message
 
"Top
 
up
 
emissions  
additive:

 
Starting
 
prevented",
 
you   must  
wait

 
around
 
5
 
minutes
 
before
 
switching  
on the ignition,

without opening the
driver's door, locking the vehicle or
introducing the key into the ignition
switch.
Switch on the ignition, then, after
10
 
seconds,
 
start
 
the
 
engine.
adBlue® additive