2013 YAMAHA RHINO 700 bulb

Rear knuckle upper and lower pivot lubrication (left and right).... 8-42
Steering shaft lubrication .............. 8-43
Wheel removal .............................. 8-44
Tire replacement ........................... 8-44
Wheel installation .......................... 8-45
Battery ........................................... 8-47
Jump-starting ................................ 8-51
Fuse replacement ......................... 8-53
Replacing a headlight bulb ........... 8-55
Headlight beam adjustment .......... 8-58
Tail/brake light bulb replacement ................................ 8-58
Troubleshooting ............................ 8-60
Troubleshooting charts ................. 8-62
CLEANING AND STORAGE............ 9-1 A. Cleaning...................................... 9-1
B. Storage ....................................... 9-2
SPECIFICATIONS.......................... 10-1 CONSUMER INFORMATION ........ 11-1
Identification number records ........ 11-1
910
11
1RB7A_EE.book Page 4 Tuesday, April 24, 2012 9:07 AM

8-55
6. Turn the key to “ON” and turn on theelectrical circuit in question to check if the
device operates. If the fuse blows again
immediately, have a Yamaha dealer
check the electrical system.
7. Install the battery compartment cover by installing the quick fastener screws.
8. Close the hood.
EVU01670Replacing a headlight bulb
If a headlight bulb burns out, replace it as fol-
lows.
1. Open the hood. (See pages 8-7–8-8 for hood opening and closing procedures.)
2. Remove the cover at the rear of the
headlight by pulling it off.1. Cover at the rear of the headlight
Specified fuses:Main fuse: 40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Signaling system fuse: 10.0 A
Four-wheel-drive motor
fuse: 10.0 A
Radiator fan fuse: 25.0 A
Backup fuse: 10.0 A
1RB7A_EE.book Page 55 Tuesday, April 24, 2012 9:07 AM

8-56
3. Remove the headlight bulb holder coverby pulling it off.1. Headlight bulb holder cover
4. Remove the headlight bulb holder by pushing it in and turning it counterclock-
wise.1. Headlight bulb holder
1RB7A_EE.book Page 56 Tuesday, April 24, 2012 9:07 AM

8-57
5. Wait for the headlight bulb to cool beforetouching or removing it. Remove the bulb
by pulling it out.
6. Insert a new headlight bulb into the bulb holder. NOTICE: Do not touch the
glass part of the headlight bulb to
keep it free from oil, otherwise the
transparency of the glass, the lumi-
nosity of the bulb, and the bulb life will
be adversely affected. Thoroughly
clean off any dirt and fingerprints on
the headlight bulb using a cloth moist-
ened with alcohol or thinner.
1. Do not touch the glass part of the bulb.7. Install the bulb holder by pushing it in and
turning it clockwise.
8. Install the bulb holder cover and the cov-
er at the rear of the headlight. NOTICE:
Make sure the headlight bulb holder
cover is securely fitted over the bulb
holder and seated properly.
9. Close the hood.
10. Adjust the headlight beam if necessary.
1RB7A_EE.book Page 57 Tuesday, April 24, 2012 9:07 AM

8-58
EVU00990Headlight beam adjustmentNOTICEIt is advisable to have a Yamaha dealer
make this adjustment.To raise the beam, turn the headlight beam
adjusting screw in directiona.
To lower the beam, turn the headlight beam
adjusting screw in direction b.1. Headlight beam adjusting screw
EVU01000Tail/brake light bulb replacement
If a tail/brake light bulb burns out, replace it as
follows:
1. Remove the quick fastener screws, nuts and bolts from panel A (if replacing the
left tail/brake light bulb) or panel B (if re-
placing the right tail/brake light bulb).1. Panel A
1RB7A_EE.book Page 58 Tuesday, April 24, 2012 9:07 AM

8-59
1. Panel B
1. Quick fastener screw (
× 8) 2. Bolt and nut ( × 2)
3. Panel A
2. Lift the cargo bed up. (See pages 4-22–
4-23 for cargo bed lifting and lowering
procedures.)
3. Remove the panel (panel A or B).
4. Remove the tail/brake light bulb holder (together with the bulb) by turning it coun-
terclockwise.1. Tail/brake light bulb holder5. Push the burnt-out bulb in and turn it
counterclockwise to remove it from the
bulb holder.
6. Push a new bulb in and turn it clockwise
to install in the bulb holder.
1RB7A_EE.book Page 59 Tuesday, April 24, 2012 9:07 AM

8-60
7. Install the bulb holder (together with thebulb) by turning it clockwise.
8. Install the panel.
9. Lower the cargo bed.
10. Install the quick fastener screws, bolts and nuts, and then tighten the nuts to the
specified torque.
EVU01010Troubleshooting
Although Yamaha vehicles receive an inspec-
tion before shipment from the factory, trouble
may occur during operation. Any problem in
the fuel, compression, or ignition systems can
cause poor starting and loss of power. The
troubleshooting chart describes a quick, easy
procedure for making checks. If your vehicle
requires any repair, take it to a Yamaha deal-
er.
The skilled technicians at a Yamaha dealer-
ship have the tools, experience, and know-
how to properly service your vehicle. Use only
genuine Yamaha parts on your vehicle. Imita-
tion parts may look like Yamaha parts, but
they are often inferior. Consequently, they
have a shorter service life and can lead to ex-
pensive repair bills.
Tightening torque:
Panel nut: 7 Nm (0.7 m·kgf, 5.1 ft·lbf)
1RB7A_EE.book Page 60 Tuesday, April 24, 2012 9:07 AM

10-4
Rear wheel:Wheel type:YXR7FD Panel wheel
YXR7FSPD Cast wheel
YXR700FAD Panel wheel
Rim size: 12 × 7.5ATFront brake:Type:
Disc brake
Operation: Unified brake
Specified brake fluid: DOT 4Rear brake:Type:Disc brake
Operation: Unified brake
Specified brake fluid:
DOT 4Front suspension:Type:Double wishbone
Spring/shock absorber type:
YXR7FD Coil spring/oil damper
YXR7FSPD Coil spring/gas-oil damper
YXR700FAD Coil spring/oil damper
Wheel travel: 185 mm (7.3 in)
Rear suspension:Type:Double wishbone
Spring/shock absorber type:
YXR7FD Coil spring/oil damper
YXR7FSPD Coil spring/gas-oil damper
YXR700FAD Coil spring/oil damper
Wheel travel: 185 mm (7.3 in)Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:U1-H11L
Voltage, capacity: 12 V, 28.0 AhHeadlight:Bulb type:Krypton bulbBulb voltage, wattage
× quantity:
Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 2
Neutral indicator light: LED
Reverse indicator light:
LED
1RB7A_EE.book Page 4 Tuesday, April 24, 2012 9:07 AM