2013 YAMAHA RHINO 700 wheel

8-55
6. Turn the key to “ON” and turn on theelectrical circuit in question to check if the
device operates. If the fuse blows again
immediately, have a Yamaha dealer
check the electrical system.
7. Install the battery compartment cover by installing the quick fastener screws.
8. Close the hood.
EVU01670Replacing a headlight bulb
If a headlight bulb burns out, replace it as fol-
lows.
1. Open the hood. (See pages 8-7–8-8 for hood opening and closing procedures.)
2. Remove the cover at the rear of the
headlight by pulling it off.1. Cover at the rear of the headlight
Specified fuses:Main fuse: 40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Signaling system fuse: 10.0 A
Four-wheel-drive motor
fuse: 10.0 A
Radiator fan fuse: 25.0 A
Backup fuse: 10.0 A
1RB7A_EE.book Page 55 Tuesday, April 24, 2012 9:07 AM

9-1
1
2
3
4
5
6
7
89
10
11
12
13
14
EVU01030
1-CLEANING AND STORAGE
A. Cleaning
Frequent, thorough cleaning of your vehicle
will not only enhance its appearance but will
improve its general performance and extend
the useful life of many components.1. Before cleaning the vehicle:
a. Block off the end of the exhaust pipeto prevent water entry. A plastic bag
and strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy,
apply degreaser with a paint brush. Do
not apply degreaser to the wheel axles. 3. Rinse the dirt and degreaser off with a
garden hose. Use only enough pressure
to do the job. WARNING! Test the
brakes after washing. Apply the
brakes several times at slow speeds
to let friction dry out the linings. Wet
brakes may have reduced stopping
ability, increasing the chance of an ac-
cident. NOTICE: Excessive water
pressure may cause water seepage
and deterioration of wheel bearings,
brakes, transmission seals and elec-
trical devices. Many expensive repair
bills have resulted from improper
high-pressure detergent applications,
such as those available in coin-oper-
ated car washers.1RB7A_EE.book Page 1 Tuesday, April 24, 2012 9:07 AM

9-3
2. Remove the spark plug, pour a tea-spoonful of engine oil into the spark plug
bore and install the spark plug. Ground
the spark plug wire and turn the engine
over several times to coat the cylinder
wall with oil.
3. Lubricate all control cables.
4. Block up the frame to raise all wheels off the ground.
5. Tie a plastic bag over the exhaust pipe outlet to prevent moisture from entering.
6. If storing in a humid or salt-air atmo-
sphere, coat all exposed metal surfaces
with a light film of oil. Do not apply oil to
any rubber parts or the seat covers. 7. Remove the battery and charge it. Store
it in a dry place and recharge it once a
month. Do not store the battery in an ex-
cessively warm or cold place [less than
0 °C (30 °F) or more than 30 °C (90 °F)].
Use of fuel stabilizer and conditioner elimi-
nates the need to drain the fuel system. Con-
sult a Yamaha dealer if the fuel system needs
to be drained.
1RB7A_EE.book Page 3 Tuesday, April 24, 2012 9:07 AM

10-1
EBU25960
1-SPECIFICATIONS
Dimensions:Overall length:2885 mm (113.6 in)
Overall width: 1385 mm (54.5 in)
Overall height:
YXR7FD 1853 mm (73.0 in)
YXR7FSPD 1901 mm (74.8 in)
YXR700FAD 1853 mm (73.0 in)
Seat height: 818 mm (32.2 in)
Wheelbase:
1910 mm (75.2 in)
Ground clearance: 280 mm (11.0 in)
Minimum turning radius: 3900 mm (154 in)Weight:With oil and fuel:YXR7FD 540.0 kg (1190 lb)
YXR7FSPD 548.0 kg (1208 lb)
YXR700FAD 540.0 kg (1190 lb)Noise and vibration level:Noise level (77/311/EEC):YXR7FD 80.2 dB(A)
YXR7FSPD 80.2 dB(A)
Vibration on seat (EN1032, ISO5008): YXR7FD Will not exceed 0.5 m/s
2
YXR7FSPD Will not exceed 0.5 m/s2
Vibration on handlebar (EN1032, ISO5008): YXR7FD Will not exceed 2.5 m/s
2
YXR7FSPD Will not exceed 2.5 m/s2
Engine:Engine type: Liquid cooled 4-stroke, SOHC
Cylinder arrangement: Single cylinder
Displacement:
686 cm³
Bore × stroke:
102.0 × 84.0 mm (4.02 × 3.31 in)
Compression ratio: 9.20 : 1
Starting system:
Electric starter
Lubrication system: Wet sumpEngine oil:Recommended brand:
YAMALUBE
1RB7A_EE.book Page 1 Tuesday, April 24, 2012 9:07 AM

10-3
Secondary reduction system:
Shaft drive
Secondary reduction ratio: 41/21 × 17/12 × 33/9 (10.142)
Transmission type:
V-belt automatic
Operation: Right hand operation
Reverse gear: 23/14 × 28/23 (2.000)
Low range:
31/16 (1.938)
High range: 31/21 (1.476)
Chassis:Frame type:
Steel tube frame
Caster angle: 5.0 °
Trail: 26.0 mm (1.02 in)Front tire:Type:Tubeless
Size: 25 x 8-12NHS
Manufacturer/model:
MAXXIS/M951Y
Rear tire:Type:Tubeless
Size:
25 x 10-12NHS
Manufacturer/model: MAXXIS/M952YLoading:Maximum loading limit:
YXR7FD 367.0 kg (809 lb)
YXR7FSPD 359.0 kg (791 lb)
YXR700FAD 367.0 kg (809 lb)
(Total weight of rider, passenger, cargo, accessories, and
tongue)Tire air pressure (measured on cold tires):Recommended:Front:
70.0 kPa (0.700 kgf/cm², 10 psi)
Rear: 98.0 kPa (0.980 kgf/cm², 14 psi)
Minimum: Front:63.0 kPa (0.630 kgf/cm², 9 psi)
Rear: 91.0 kPa (0.910 kgf/cm², 13 psi)Front wheel:Wheel type: YXR7FD Panel wheel
YXR7FSPD Cast wheel
YXR700FAD Panel wheel
Rim size:
12 × 6.0AT
1RB7A_EE.book Page 3 Tuesday, April 24, 2012 9:07 AM

10-4
Rear wheel:Wheel type:YXR7FD Panel wheel
YXR7FSPD Cast wheel
YXR700FAD Panel wheel
Rim size: 12 × 7.5ATFront brake:Type:
Disc brake
Operation: Unified brake
Specified brake fluid: DOT 4Rear brake:Type:Disc brake
Operation: Unified brake
Specified brake fluid:
DOT 4Front suspension:Type:Double wishbone
Spring/shock absorber type:
YXR7FD Coil spring/oil damper
YXR7FSPD Coil spring/gas-oil damper
YXR700FAD Coil spring/oil damper
Wheel travel: 185 mm (7.3 in)
Rear suspension:Type:Double wishbone
Spring/shock absorber type:
YXR7FD Coil spring/oil damper
YXR7FSPD Coil spring/gas-oil damper
YXR700FAD Coil spring/oil damper
Wheel travel: 185 mm (7.3 in)Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:U1-H11L
Voltage, capacity: 12 V, 28.0 AhHeadlight:Bulb type:Krypton bulbBulb voltage, wattage
× quantity:
Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light: 12 V, 5.0/21.0 W × 2
Neutral indicator light: LED
Reverse indicator light:
LED
1RB7A_EE.book Page 4 Tuesday, April 24, 2012 9:07 AM

10-5
Coolant temperature warning light:
LED
Engine trouble warning light: LED
Parking brake indicator light:
LED
On-Command four-wheel-drive/differential gear lock indica-
tor:
LCD
High-range indicator light: LED
Low-range indicator light: LED
Differential gear lock indicator light:
LED
Helmet/Seat belt indicator light: 14 V, 1.7 W
Fuses:Main fuse:
40.0 A
Fuel injection system fuse: 10.0 A
Headlight fuse: 15.0 A
Signaling system fuse:
10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Backup fuse:
10.0 A Four-wheel-drive motor fuse:
10.0 A
Radiator fan fuse: 25.0 A
For Europe only
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure
levels, this cannot be used reliably to determine
whether or not further precautions are required.
Factors that influence the actual level of exposure
of work-force include the characteristics of the
work room, the other sources of noise, etc. i.e. the
number of machines and other adjacent process-
es, and the length of time for which an operator is
exposed to the noise. Also the permissible expo-
sure level can vary from country. This information,
however, will enable the user of the machine to
make a better evaluation of the hazard and risk.
1RB7A_EE.book Page 5 Tuesday, April 24, 2012 9:07 AM