2013 SSANGYONG TURISMO seat

02-110000-00
2) Cylinder Head
(1) Cylinder head mating surface check
Specified value ▶
Measure the cylinder head height "A".
1.
Insert the valves into the valve guides and
measure the recesses. 2.
Valve recess “a”0.6 to 1.0mm
(2) Cylinder head pressure Leak test
Immerse the cylinder head with the pressure plate into warm water (approx. 60°C) and
pressurize with compressed air to 2 bar.If the height is less than the limit, the
cylinder head must be replaced. -
If the measured value is out of the specified
range, machine the valve seat as much as
necessary until the specified value is
achieved. -
Total height "A"131.9 to 132.1 mm
Minimum height after machining131.9 mm
Flatness Longitudinal direction0.1 / 150
Transverse direction0.15
Parallel deviation of cylinder headbelow 0.1 mm
Peak-to valley of surfaceRmax 7 Rz 6.3
valve recess "a" Intake valve0.6 to 1.0 mm
Exhaust valve0.6 to 1.0 mm

02-22
5) Seat Belt Warning
The seat belt warning light comes on and the chime buzzer in the ICM box sounds for 6 seconds
when turning the ignition key to “ON” from “OFF”. If the seat belt is fastened before turning
the ignition key to “ON” position, the warning light in the indicator display blinks for 6
seconds, however, the chime buzzer does not sound.
The seat belt warning light goes off and the chime buzzer in the ICM box stops when turning the
ignition switch to “OFF” position.
The chime buzzer stops and the seat belt warning light stays on for the specified duration (6
seconds) when fastening the seat belt during the warning operation.
The seat belt warning light comes on and the chime buzzer sounds for 6 seconds again when
unfastening the seat belt during fastening operation. 1.
2.
3.
4.

06-38510-00
1. SPECIFICATIONS
1) Center Fascia Switch
Item Specifications
Center fascia switch &
bezel assemblyHazard warning flasher switch DC 12 V 10 A(lamp load)
Windshield heated glass switch
DC 12 V 1 A(inductive load) Rear heated glass switch
ESP OFF switch
Driver/front passenger seat warmer
switch
Fog lamp switch
2) 4WD Switch & HLLD Switch & Rear Wiper Operation Switch
Item Specifications
4WD switch &
HLLD switch &
rear wiper operation
switch assemblyWasher switch DC 12 V 3.8 A(lamp load)
Wiper switch DC 12 V 3.0 A (max. 10 A)
4WD switch DC 12 V 300 mA
HLLD switch DC 12 V 1 A (inductive load)
3) Steering Wheel Switch
Item Specifications
Steering wheel switch Rated voltage DC 5 V 0.1 A(rated load)
Operation temperature-30℃~+80℃

06-98510-00
Center fascia switch
Passenger’s Window Switch
(same with rear window
switches)
Overhead console switch
Auto light sensor
Cigarette lighter
Power outlet socket
Driver’s seat
warmer switch
Rear fog lamp
switchESP OFF switch
Defogger switch
Passenger’s seat
warmer switch Front fog lamp switch
Front room lamp switch
Sunroof switch
Door coupled room lamp switch
Hazard warning
flasher switch

04-4
Rear axle assembly
Mounting hole position and seat pan angle for rear axle changed due to change of rear sub frame
2. CHANGES
Changes in rear axle assembly ▶
Changes in rear axle shaft assembly ▶
Rear Axle Shaft Assembly
Increased rear axle shaft length (15.0 mm) due to change of rear sub frame
Mounting section

02-38810-03
1. SPECIFICATIONS
Description Item Specification
Air bag unit
(SDM)Operating voltage 10.0 V to 16.5 V
Voltage for diagnosis and self-
diagnosis8.0 V to 16.5 V
Operating temperature-40℃ ~ 85℃
Storage temperature-40℃ ~ 90℃
Overvoltage protection 24 V
Ground resistance100 mΩ or less
Driver/passenger
air bag moduleOperating voltage 8.0 V to 16.5 V
Seat air bag moduleOperating voltage 10.0 V to 16.5 V
Side impact sensor voltage 8.0 V to 16.5 V
Seat belt pretensioner Operating voltage 10.0 V to 16.5 V
If you measure the air bag module using a multitester, the air bag module may be deployed,
causing a personal injury.
Never use the multitester to check the air bag module.

02-4
2. OPERATION
1) Air Bag
▶Air bag inflates when:
In response to a severe frontal impact, the driver’s and front passenger’s air bags
deploy at the same time to supplement the seat belts to prevent or reduce any personal
injuries. -
▶Air bag can inflate when:
Underbody impact from the road surface; impact against the curb at a very high speed;
dropping impact onto the road surface with a large angle -
▶Air bag does not inflate when:
Rollover, side impact or rear impact
If the severity of impact to the vehicle is not significant and the seat belts are enough to protect
occupants. -
-
Air bag seldom inflates when: ▶
Oblique impact, rollover
Weak impact in which the sensor is unable to detect (under the inflation requirements)
Impact against narrow objects such as a utility pole or a tree
The vehicle falls into a drainage or a puddle
The front of the vehicle crashes into a high impact point vehicle such as a truck
Impact on the hood by falling stones
The air bag warning light is on
Moderate or severe impact to the middle of the vehicle body’s side structure. In that case,
only the side curtain air bags deploy. -
-
-
-
-
-
-
-

02-58810-03
When a severe frontal impact occurs, seat belt
pre-tensioners rewind the seat belts
immediately to restrain the occupants to their
seats. It helps the effective operation of the
seat belts and airbags.
2) Pre-tensioner
3) Warning for Air Bag
Do not diagnose the circuit with a circuit tester. Do not attempt to modify any air bag components
including the steering wheel, air bag mounting area, and harness.
Do not impact any air bag components including the steering wheel, air bag mounting area, and
harness by hand or tools. You may get injured by sudden deployment.
The air bag components will be very hot after deployment. Do not touch them.
Once the air bag system is triggered, the triggered air bag assembly should be removed from the
vehicle and replaced with new one.
The air bag contains explosive materials, so contact Ssangyong Dealer or Ssangyong Authorized
Service Operation when trashing or replacing it.
Incorrect air bag inspection can be dangerous and cause injuries. The air bag system must be
disposed only by Ssangyong Dealer or Ssangyong Authorized Service Operation.
Replace the steering wheel with only Ssangyong genuine part.
When the engine starts, the air bag warning lamp comes on for a system check. It goes out after 3
to 7 seconds when the system is normal. If this warning lamp stays ON, then the system may be
defective. Have the air bag system checked immediately by Ssangyong Dealer or Ssangyong
Authorized Service Operation.
The seat belt and air the bags are the most effective when you are sitting well back and upright in
the seat.
A child restraint system must not be placed on the front seat. The infant or child can be severely
injured by an air bag inflation in case of an accident.
Do not carry your child on your lap while driving. You cannot resist against the impact pressure in an
accident.
The child could be crushed between you and the parts of the vehicle.
Do not place any objects on the air bag inflation location. You may get injured by those objects
during deployment.
Do not attach any objects such as a sticker, scent bottle, or phone holder on the steering wheel pad
and to the dashboard. -
-
-
-
-
-
-
-
-
-
-
-
-
-