2013 SSANGYONG TURISMO relay

02-58710-01
The remote engine control function has been deleted in this model.
1. COMPONENTS
STICS / ICM module
Air bag ECU
Sends the vehicle collision
signals to STICS.
Theft deterrent horn
Installed under the battery.
This horn works only for the
theft deterrent function, panic
function, and remote starting.
SCAN-tool
SIW is used for REKES key
coding and trouble
diagnosis.
REKES
Added the escort and panic
function
RK STICS
ICM module
This module contains
various relays, chime and
buzzer controlled by STICS

02-6
2. FUNCTIONS OF RK STICS
1) Wiper Control
(1) Wiper MIST and Washer Coupled Wiper
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch for 0.2 ~
0.59 seconds (T2) with the ignition key “ON”, and it is turned off when the parking terminal
is turned off. 1.
The wiper relay is turned on 0.3 seconds (T1) after turning “ON” the washer switch over 0.6
seconds (T2) with the ignition key “ON”, and it is turned on three times immediately after
turning off the washer switch. 2.

02-98710-01
▶ Rain sensing operation point
The wiper relay is turned on and the wiper motor runs one cycle when the ignition key is turned to
“ON” position (while the wiper switch is in “AUTO” position).
The wiper relay (LO) is turned on and the wiper motor runs one cycle when changing the wiper
switch to “AUTO” position from any other positions (while the ignition key is in “ON”
position). When the wiper switch is turned to “AUTO” position again from other positions,
the system drives the wiper relay (LO) to run the wiper motor one cycle only when the rain sensor
detects the “Rain Detected” signal. 1)
2)

02-10
The wiper relay is turned on and the wiper motor runs one cycle when the volume sensitivity is
increased (ex: from 0 to 1) (while the ignition key is in “ON” position, the wiper switch is in
“AUTO” position, and the wiper motor is in “Parked” position). However, the wiper motor can
be operated only when the rain sensor detects the “Rain Detected” signal.
▶ Rain sensing sensitivity control
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs only
one cycle. *

02-12
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 3 during receiving the malfunction signal (1) from the rain sensor. However, the
wiper motor can be operated only when the rain sensor detects the "Rain Detected" signal. 1)
If the volume sensitivity is changed more than 2 stages within 2 seconds, the wiper motor runs
only one cycle. ▶ Defective rain sensor

02-138710-01
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 3 from 4 during receiving the malfunction signal (2) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is changed to 2
from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)

02-158710-01
The wiper relay continues to output when the parking terminal is fixed at the ground or IGN
while the wiper relay is “ON” (INT switch = ON or Washer switch = ON) (The output
stops immediately after turning off the switch) - (1) Wiper MIST and washer coupled wiper
When turning on the washer switch while the wiper relay is operating.
1)
If the wiper relay “ON” request time is shorter than the remained “ON” time, it is
disregarded. -
(2) Speed sensitive INT (intermittent) wiper
The wiper relay continues to output for remaining “ON” time even when the INT switch is
turned off.
IGN 2 switch “ON”, INT switch “OFF”: resume the intermittent time when turning “ON
IGN 2 switch “OFF”, INT switch “ON”: resume the intermittent time when turning “ON 1)
2)
3)
(3) Controls when the wiper motor parking is defective

02-16
▶INT Switch Auto Position Reminder (Power-Up Reminder Wiper)
When turning off and on the auto INT switch, the system drives the wiper motor through LOW
relay regardless of communication with rain sensor.
When turning the INT-AUTO switch from the "OFF" to "ON" position with the ignition switch in
the "ON" mode, the LOW relay operates to drive the wiper motor for 1 cycle, regardless of the
rain sensor communication.
After that, when turning the INT-AUTO switch from the "OFF" to "ON" position, the LOW relay
operates to drive the wiper motor for 1 cycle only if data from the rain sensor indicates rain
drops. 1.
2.