2013 SSANGYONG TURISMO bumper

07-6
Rear Tailgate Combination Lamp
Design changed
Side view ▶
Backup lamp
Stop lamp and tail
lamp (P21/5W)
Backup lamp (W16W)
Reflex reflector lamp (Rear fog lamp)
Design change due to changed rear bumper
Side repeater lamp design changed

09-4
2. CAUTIONS
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while washing,
since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is moved
into "R" position with the ignition key "ON".
If the system is defective, the warning buzzer sounds for 3 seconds when moving the gear shift
lever to “R” position with the ignition ON. Be careful not to confuse this and the parking aid
alarm (in 50 cm). 1.
2.
3.
4.
5.
- Note that the display does not show everything in the rear area. Always check
nobody, especially animals and children, is behind the vehicle when parking or
reversing.
- If you can not properly check the vehicle behind, get out of the vehicle and then
visually check it.
The parking aid system will not work or improperly work under following cases: ▶
1) Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2) Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally after
cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy commercial
vehicles)
When a high-power radio is turned on -
-
-
-
3) Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after cleaned)
Surrounding temperature of sensor is too high (approx. over 80°C) or too low
(approx. below -30°C) -
-
4) Not defective but may cause malfunction
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy commercial
vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
-

09-6
Shift lever (R position)
Sends reverse signal to PAS unit
1. Overview
The parking aid system (PAS) is a supplementary device which detects the distance to any obstacle
with the ultrasonic sensors equipped to the rear bumper and warns the driver with alarm sounds, when
the vehicle is moving backward.
The system emits the ultrasonic wave signals from the sensors on the rear bumper with a specific
interval and detects the reflected signals from obstacles.
The alarm interval becomes shorter as the obstacle approaches to assure the safety distance and to
facilitate parking of the vehicle.
2. Layout
ICM box
Buzzer integrated into ICM box
(indicates distance as alarm interval)

09-98790-01
4) Detection range by sensors
Height Ground ~ 15 cm15 cm ~ lower side of
bumperLower side of bumper
~
Possible to detect Impossible to detect Not detected Detected
Tolerance± 5 cm ± 5 cm ± 5 cm
5) Distance calibration by temperature from temperature sensor
The ultrasonic wave sensor directs the distance value by receiving the sensor operating temperature
from the sensor and compensating for the detecting deviation since it varies depending on the ambient
temperature.
TemperatureThermistor
output valueTemperatureThermistor
output value
+80℃6.93 V+20℃2.16 V
+70℃6.24 V+10℃1.45 V
+60℃6.04 V0℃1.15 V
+50℃5.34 V-10℃0.98 V
+40℃4.62 V-20℃0.88 V
+30℃4.15 V-30℃0.75 V

07-10
Spring link
2) Rear Suspension
Rear coil springWheel carrier assembly
Rear sub frame bush
Nut
Upper washer Upper
bush
Bumper stopper Lower bush
Dust coverShock absorber
Bolt
NutCollar
Front
Rear
Rear shock absorber assembly

06-50000-00
Front bumper assembly
Front bumper design changed
Tailgate Panel Assembly
Tailgate panel design changed
Door outside handle assembly
Front and rear parts design changed

06-6
Radiator grille assembly
Radiator grille design changed
Rear bumper assembly
Rear bumper design changed
Fashion rail assembly
Fashion rail design changed

06-70000-00
Spoiler assembly
Spoiler design changed
Front
Front bumper fascia change results in installation design change
Rear
Changed from split type to integral type
Wheel house cover