Page 148 of 751
09-31451-01
1. SPECIFICATION
AlternatorCrankshaft pulley : Alternator pulley 1 : 2.94
Normal output (idling/2200 rpm) 70/120 A
Regulator voltage 14.6 V
BrushLength 12.5 mm
Wear limit 7 mm
BatteryType MF
Capacity 90 AH
Unit Description Specification
Page 294 of 751

07-51452-01
1. DESCRIPTION AND OPERATION
1) Battey
The sealed battery is standard on all cars. There are no vent plugs in the cover.
The battery is completely sealed, except for two small vent holes in the sides.
These vent holes allow the small amount of gas produced in the battery to escape.
The battery has the following advantages over conventional batteries:
No water addition for the life of the battery.
Overcharge protection. If too much voltage is applied to the battery, it will not accept as much current
as a conventional battery.
In a conventional battery, the excess voltage will still try to charge the battery, leading
to gassing, which causes liquid loss.
Not as liable to self-discharge as a conventional battery. This is particularly important when a battery
is left standing for long periods of time.
More power available in a lighter, smaller case. ·
·
·
·
The battery has three major functions in the electrical system.
First, the battery provides a source of energy for cranking the engine.
Second, the battery acts as a voltage stabilizer for the electrical system. Finally, the battery
can, for a limited time, provide energy when the electrical demand exceeds the output of the generator.
2) Ratings
<0068004700890088009b009b008c009900a00047008f0088009a0047009b009e0096004700990088009b00900095008e009a00610047004f005800500047008800470099008c009a008c0099009d008c0047008a008800970088008a0090009b00a0004700
990088009b00900095008e0047008b008c009a0090008e0095>ated at 27°C(80°F), which is the
time a fully charged battery will provide 25 amperes of current flow at or above 10.5 volts (2) a cold
cranking am
p rating determined under testing at -18°C(0°F), which indicates the cranking load
capacity. ▶
(1)Reserve Capacity
The reserve capacity (RC) is the maximum length of time it is possible to travel at night with the minimum
electrical load and no generator output. Expressed in minutes, the RC rating is the time required for a
fully charged battery, at a temperature of 27°C(80°F) and being discharged at a current of 25
amperes, to reach a terminal voltage of 10.5 volts.
Page 417 of 751
07-37810-01
1. SPECIFICATIONS
Unit Item Specification
Wiper motor Rated voltage DC 12 V
Operating voltage DC 10 to 15 V
Lowest operating voltage DC 8 V or less
Low revolutions46 ± 5 RPM
High revolutions70 ± 9 RPM
Wiper arm and blade Wiper arm length Driver 508 mm
Passenger 537 mm
Wiper blade
lengthDriver 550 mm
Passenger 475 mm
Rain sensor Operating voltage DC 9 to 16 V
Load Max. 200 mA (relay load)
Operating temperature-30˚C to 85˚C
Mounting location Top center of inner side of windshield
glass
Washer reservoir tank Volume 3.0 L
Page 522 of 751

04-6
2) Overview
Driving elements ▶
The driving elements consist of two flat surfaces machined to a smooth finish.
One of these is the rear face of the engine flywheel and the other is the clutch pressure plate. The clutch
pressure plate is fitted into a clutch steel cover, which is bolted to the flywheel.
Driven elements ▶
The driven element is the clutch disc with a splined hub which is free to slide lengthwise along the splines
of the input shaft.
The driving and driven elements are held in contact by spring pressure. This pressure is exerted by a
diaphragm spring in the clutch cover pressure plate assembly.
Operating Elements ▶
The clutch "release" system consists of the clutch pedal and clutch release cylinder.
This system directly releases the clutch by using hydraulic pressure while the conventional clutch system
releases the clutch by using release lever and release fork. This system provides higher efficiency than
conventional clutch system, and its durability is superior.
Clutch master cylinder (mounted on clutch pedal)
Concentric slave cylinder pipe (mounted inside of transmission) -
-
Page 525 of 751
05-33310-00
1. SPECIFICATION
Description Specification
Structure Universal joint with yoke arm and spider
Number of spiders Front Part time T/C Two
Rear Three
Runout Max. 0.3mm
Unbalance Max. 18 g.cm / 4,500 rpm
Dimension of front
propeller shaft (Length x
Dia.) (mm)A/T 552.3*Φ63.5 (Compressed)
M/T 603.8*Φ63.5 (Compressed)
Dimension of front
propeller shaft (Length x
Dia.) (mm)2WD Front1136.0*Φ63.5
Rear743.*Φ63.5(Compressed)
4WD(M/T) Front785.1*Φ63.5
Rear743.*Φ63.5(Compressed)
4WD(A/T) Front836.8*Φ63.5
Rear743.*Φ63.5(Compressed)
2. TIGHTENING TORQUE
Fastener Tightening torque
Mounting bolts for front/rear axle 66.7 ~ 73.5Nm
Mounting bolts for T/M and T/C 79.4 ~ 87.2Nm
Mounting bolts for center bearing 78.4 ~93.1Nm
Page 526 of 751
05-4
1. OVERVIEW
The propeller shaft transfers the power through the transmission and transfer case to the front/rear axle
differential carrier (final reduction gear).
It is manufactured by a thin rounded steel pipe to have the strong resisting force against the torsion and
bending.
Both ends of propeller shaft are connected to the spider and the center of propeller shaft is connected to
the spline to accommodate the changes of the height and length.
The rubber bushing that covers the intermediate bearing keeps the balance of rear propeller shaft and
absorbs its vibration.
Function of propeller shaft ▶
Transmits driving torque.
Compensates the angle change (universal joint / CV joint).
Compensates the axial length change (splines for the slip joint). -
-
-
Front propeller shaft
Rear propeller shaft
Page 527 of 751
06-2
1. SPECIFICATIONS
Location Front Axle Rear Axle
GearType Hypoid←←←
SizeØ182.8 mm ← Ø228.6 mm ←
Offset28.58 mm
(DYMOS)
35 mm(Tongil)←30 mm -
Housing Steel←Steel casting←
OilTypeSAE 80W/90, API
GL-5←SAE 80W/90, API
GL-5←
Capacity 1.4 L←
2.0L
←
Length 448.0 mm←469.0 mm←
Witdh 681.9 mm←1,717.7 mm←
Weight 45 kg←90 kg←
Specification M/T A/T M/T A/T
Gear ratio4.55R(5MT DSL)
4.89R(5MT GSL)3.54(5AT DSL)
3.91(6AT DSL)4.55R(5MT DSL)
4.89R(5MT GSL)3.54(5AT DSL)
3.91(6AT DSL)
Page 528 of 751
07-33240-01
1. SPECIFICATIONS
Description Specifications
Type Part-time transfer case
Total length 343 mm
Mating surface of front flange 40 mm
Weight 32.4 kg (including oil)
Oil capacity 1.4 L
Oil type ATF DEXRON III
Location Transfer case
Major element Housing Part-time & TOD
Bolt 11 ea, M8 x 1.25
Input shaft A/T: outer spline
M/T: inner spline