2013 SSANGYONG NEW ACTYON SPORTS display

04-38210-01
1. SPECIFICATIONS
Item Specification
Rated voltage DC 13.5 V
Operating voltage DC 9 V ~ 16 V
Checking voltage DC 13.5 V
Operating temperature-30℃ ~ +80℃
Storage temperature-40℃ ~ +85℃
Illumination color Dial White
Pointer Red
LCD Red
Displays on Instrument
ClusterWarning and indicator
lamp1 blue indicator
13 red indicators
7 green indicators
8 yellow indicators
Gauge Vehicle speed
Fuel level
Engine coolant temperature
Engine speed (rpm)
LCD display Driving distance
Trip meter
Gear position display
Gear position display in
A/T(Left hand of LCD
display)A/T vehicle P, R, N, D, 1, 2, 3, 4, 5, 6
M/T vehicle R

04-58210-01
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
SSPS warning light
Immobilizer indicator
Glow indicator
ESP indicator/warning light
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33. It sends and receives information to/from each unit through CAN communication line. The LCD display
and separate ESP ON/OFF indicator are newly added.

04-14
3) Fuel Level Gauge
The fuel level gauge displays the resistance value of the float on the fuel sender in the fuel tank through
a pointer. Note that this vehicle doesn't have a service hole for checking the fuel sender connector in the
fuel tank.
The fuel sender and its connector can be checked and replaced only when the fuel tank is removed.
The power supply and resistance value should be measured at the connector in front of the fuel sende
r
(refer to wiring diagram).
When the power supply and output resistance are normal, the float operation by fuel level may be
defective; if so, replace the fuel sender.
Low fuel warning lamp comes on when:
The fuel level drops to 9 L or less. The lamp goes off if the fuel level reaches 9.5 L or more.This table shows the tolerance and resistance value changes by fuel level in normal conditions.
Therefore, the differences that can be occurred by the road conditions and fuel fluctuations are
ignored.

04-158210-01
4) Coolant Temperature Gauge
The coolant temperature gauge displays the coolant temperature with a pointer. The angle of pointer
that changes by coolant temperature is as shown below.
Measurement of coolant temperature sensor resistance
Measure the resistance between the terminal and the ground with an ohmmeter and replace if the
resistance is out of specified range.
Temperature (ºC)20 60 80 100 120
Resistance (Ω)2449Ω ± 5% 589.4kΩ ±
5%321Ω ± 5%185.7kΩ ±
5%112.9kΩ ±
5%
Voltage (V)3.615 1.910 1.259 0.819 0.536
When the resistance value by coolant temperature is within the specified range, check thermostat,
water pump, radiator related coolant circuit for normal operation. Also, check the wiring harnesses
and connectors for proper connection.

04-16
Change
OrderMode LCD Display Description
1 TRIP A The maximum distance value that can be displayed is
999.9 km with increments of 0.1 km. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
2 TRIP B The maximum distance value that can be displayed is
6,213.09 mi with increments of 0.62mi. The trip meter is
reset to 0.0 km when the value reaches above 999.9 km.
When measuring a trip distance, reset the distance value
in the mode you want to use by pressing the TRIP switch
for 1 sec. or more.
3 Distance to
emptyThe estimated distance that can be traveled is calculated
based on the current fuel level.
If the DTE is less than 50 km, "---" flashes on the display.
4 Driving time The driving time from resetting the value (0:00) until now
is displayed. The value displayed is accumulated while
the engine is running even if the vehicle is not driven. The
display range is 00:00 to 99:59. When measuring the
driving time, press the TRIP switch for 1 sec. or more to
reset the value.
5 Average
fuel
economyThe average fuel economy from resetting the value (--.-)
until now is displayed. The value displayed is
accumulated while the engine is running even if the
vehicle is not driven. The display range is 0.0 to 99.9
km/h. When measuring the average fuel economy, press
the TRIP switch for 1 sec. or more to reset the value. "--.-"
is displayed on the screen when resetting. The value is
reset automatically whenever the vehicle is fuelled.
5) Description for LCD Display
LCD display
Mode Description ▶

04-178210-01
Change
OrderMode LCD Display Description
6 Instant fuel
consumptionThe fuel range is calculated based on the distance
driven and fuel consumed every 2 seconds. If the
vehicle speed is below 10 km/h or the engine rpm is
200 rpm or less, the instant fuel economy is not
displayed. The display range is 0.0 to 99.9 km/.
7 Brightness
adjustmentThe brightness of the illumination can be adjusted in 6
steps by pressing the TRIP switch briefly (less than 1
sec.). The display is changed from ILL1 to ILL6 every
time the switch is pressed. If you select one level
within the range and press and hold the TRIP switch,
the brightness level is memorized. If there is no TRIP
switch input for 5 seconds or more, the mode is
switched to TRIP A mode automatically. When the
battery is reinstalled, the brightness level is reset to
level 4.

04-198210-01
Brightness of LCD display when turning ON/OFF tail lamp ▶
Sequen
ceLevelTail lamp OFF Tail lamp ON
Display brightness Brightness
ratioDisplay brightness Brightness
ratio
1 ILL1 25% 5%
2 ILL2 40%9%
(LCD: 12%)
3 ILL3 55%13%
(LCD: 19%)
4 ILL4 70%17%
(LCD: 26%)
5 ILL5 85%21%
(LCD: 33%)
6 ILL6 100%25%
(LCD: 40%)
Illumination conditions of LCD display when turning ON/OFF tail lamp ▶
The illumination for the LCD display comes on when turning on the tail lamp and is adjustable only when
the ignition is ON. When turning on the tail lamp switch with the ignition OFF, the tail lamp comes on but
the LCD display is not illuminated. Refer to the illustration below.
IGN ON
(Comes on regardless of whether the tail lamp
switch is turned ON or OFF)Tail lamp comes on with IGN OFF
(Tail lamp comes on but the illumination for
LCD display is not turned on)

04-22
How to enter self-diagnosis mode ▶
Turn the ignition ON with the TRIP switch pressed.
Press and hold the TRIP switch for 5 to 10 sec. with the ignition ON.
Press and hold the TRIP switch for less than 10 sec. and then cycle the switch between ON and
OFF 5 times within 3 sec.
Confirm that the self-diagnosis mode is activated through the instrument cluster. 1.
2.
3.
4.
4. SELF-DIAGNOSIS CHECK
Self-diagnosis OFF ▶
If the engine speed increases to 396 rpm or more while the engine is cranking or the ignition key is
turned OFF in self-diagnosis mode, the self-diagnosis mode is turned OFF automatically.
Operating process ▶
Speed gauge: changes from 0 to 220 km
RPM gauge: changes from 0 to 6,000 rpm
Fuel gauge: changes from E to F
Temperature gauge: changes from C to H
Warning/Indicator lamps: All indicator/warning lamps controlled by MICOM are turned ON.
Dimming: Illuminates at the highest lighting level.
LCD display: All elements are activated. 1.
2.
3.
4.
5.
6.
7.