2013 SKODA OCTAVIA buttons

  - Backward and forward menu navigation (the key functions are descri-
bed in the relevant chapters)
CD slot 
- Eject CD
SD memory card slot

Switching the unit on/off
First read and observe the introductory information given on page 5.
›
Press the  knob to switch the device on or off.
When the device is switched on, the audio source and operating mode that were active before switching off the device will be restored.
If telephone mode was active before the device was switched off and if the igni-tion or the Bluetooth ®
function are not switched on, the following message is dis-
played: Please connect a mobile telephone. Switch on the ignition or the Blue-
tooth ®
function » page 13.
If the vehicle key is pulled out of the ignition lock while the unit is switched on, the unit will switch off automatically. After switching on the ignition, the unit is
turned on automatically.
If the device was switched off using the 
knob, then the device will not switch
on automatically after switching on the ignition.
If your vehicle is fitted with the KESSY system, the device will switch off automat- ically after the engine has been turned off and the door opened.
When the ignition is switched off, the system switches off automatically after ap-
prox. half an hour (discharge protection of the vehicle battery).

Adjusting the volume
First read and observe the introductory information given on page 5.
Increase the volume
›
Turn the  knob to the right.
11121314
Reduce the volume›Turn the
 knob to the left.
Muting›
Press the MUTE button
or
›
Set the volume to 0 using the  knob.
CAUTION
The car speakers may be damaged if the volume is set too loud or is distorted.
Note
■
The change in volume is displayed on the device display screen.■The following symbol appears in the display when the sound is muted : .■
Some connected sources allow the volume to be changed directly at the source.
■
Excessively high volumes can cause sound resonance in the vehicle.
■
The loudspeakers in the vehicle are designed for a power output of the device
of 4x20 W.

Unit operation
 Introduction
This chapter contains information on the following subjects: Operate via the device display screen
7
Operate using the buttons on the operating lever
8
Operation via the buttons / wheels on the multifunction steering wheel -
Audio menu
8
Operation via the buttons / wheels on the multifunction steering wheel -
Telephone menu
10
First and foremost, pay attention to the safety instructions » page 4 , Important
notes .
Some of the device's features are also displayed in the MAXI DOT display 1)
. De-
pending on the equipment, these features can be operated as follows. 
1)
The display in the MAXI DOT is described in the
» Manual , chapter Information system
6Introductory information

■With the buttons on the operating lever » page 8
■ With the buttons and wheels on the multifunction steering wheel » page 8
Note
The buttons and wheels on the multifunction steering wheel will also be lit if the
ignition and the side light are switched on.
Operate via the device display screen
Fig. 2
Displays
First read and observe the introductory information given on page 6.
Display of menus, menu items and functions Currently selected menu/menu item
Previous menu item
Next menu item
Higher-level menu
ABCDFunction of the menu/menu item
Function with “checkbox”
› 
- Function is switched on
› 
- Function is switched off
Selecting menu/menu item
Select by turning the menu knob 2
» Fig. 1 on page 5.
Confirming menu/menu item
Confirm by pressing the menu button
2
.
Confirming function of menu/menu item
Confirm the function of menu/menu item
E
» Fig. 2 by pressing the correspond-
ing key
3
» Fig. 1 on page 5.
Returning to higher-level menu
Return by pressing the BACK
button.
Switching function on/off with “checkbox” Switch the function on/off by pressing the menu button
2
.
Note
■ Greyed out menus or menu items are not enabled or available.■For some menus or menu items, the current setting is displayed, e.g. Distance:
km or Distance: mi .■
If the device is not currently being used, the display will return to the higher-
level menu after a few seconds.
EF7Introductory information

Operate using the buttons on the operating leverFig. 3
Buttons on the control lever
First read and observe the introductory information given on page 6.
The separate menus and menu items displayed in the MAXI DOT display can be
operated with the buttons on the control lever.
Press and hold - open main menu
Press briefly - select individual menu items or menus
Press briefly - select menu item or menu

AAB
Operation via the buttons / wheels on the multifunction steering wheel - Audio menu
Fig. 4
Multifunction steering wheel: control buttons and wheels
First read and observe the introductory information given on page 6.
Each item in the Audio menu displayed in the MAXI DOT display can be operated
with the buttons/wheels on the multifunction steering wheel. 
Control buttons and wheelsButton/
wheel
» Fig. 4ActionRadioMedia
1Press brieflyChange source, change frequency band1Press and hold but- tonSwitch between the Radio and Media operating modes, and open the last context status (e.g. the last radio station or track to be played)a)2Press brieflySwitch off/on tone b)
Start/stop playback2Turn upwardsIncrease the volume2Turn downwardsReduce the volume 8Introductory information

Operation via the buttons / wheels on the multifunction steering wheel - Telephone menuFig. 5
Multifunction steering wheel: control buttons and wheels
First read and observe the introductory information given on page 6.
Items in the MAXI DOT display telephone menu can be operated with the but-
tons / dials on the multifunction steering wheel.
The functions of the menu currently active on the phone can be controlled with the buttons and wheels.

Buttons and wheels of the Phone menuButton/wheel
» Fig. 5ActionFunction1Press brieflyMUTE1Turn upwardsIncrease the volume1Turn downwardsReduce the volume2Press brieflyAccept call, end call, entry in the main menu of the telephone, call list, call the dialled contact2Press and hold buttonReject call, redial last call3Turn up/downCall list, previous menu item3Press brieflyConfirm selected menu item4Press brieflyReturn to a previous level in the menu4Press and hold buttonReturn to Main MenuTelephone call function in the MAXI DOT display
Depending on the context, you can select the following functions:
Incoming call ■  Accept - Answer a call
■  Reject - Reject a call
■  Ignore - Ignore a call
Outgoing call
■  End call - End a callCurrent call
■  End call - End a call
■  Mic. off - Microphone off
■  Mic. on - Microphone on
Symbols in the MAXI DOT displaySymbolMeaningCharge status of the phone battery a)Signal strengtha)
10Introductory information

Audio
Radio
Introduction
This chapter contains information on the following subjects:
Main menu
16
Find and store radio station
16
Select frequency band and radio station
17
Switching traffic programme TP on/off
18
First and foremost, pay attention to the safety instructions » page 4 , Important
notes .
The device allows reception of radio stations in from FM or AM frequency ranges
as well as additional information from RDS broadcasts in the FM range.

Main menu
First read and observe the introductory information given on page 16.
Accessing radio mode in main menu
›
Press the RADIO button.
The most recently tuned radio station plays.
Symbols in the display
SymbolMeaningSound is mutedTraffic information station Station without traffic information ,  ,  , Currently selected frequency band and memory group a)Radio station is selected based on desired station top-
ic » page 12 , Radio settingsSymbolMeaningRadio station from the station list is a station from the
preset list Auto-play function for available radio stations for 10 sec-
ondsa)
PTY (programme type) - Refers to the type of the programme transmitted by the radio station.

Find and store radio station
First read and observe the introductory information given on page 16.
If no memory group is displayed for the frequency bands,
›
press the RADIO button
→ menu button
2
» Fig. 1 on page 5.
Station searches are affected by selection of the PTY filter » page 12 and by
switching on/off of the TP function.
Search options
■ TP - Switches traffic programme on/off » page 18
■ Manual - Manual station search
■ Scan - Successive play of all receivable stations in the current frequency band or
the current station buttons for five seconds each ■ OK - Stops auto-play function at the current radio station
■ Skip - Selects another radio station
■ Auto store - Automatic station search
Manual station search
Pressing the Manual button starts a manual station search.
Manual tuning is performed by turning the menu button
2
» Fig. 1 on page 5 or
the keys  .
Pressing the OK button stops the manual station search at the currently tuned
radio station.
Automatic station search
Pressing the Auto store key starts an automatic station search.
Auto store... is displayed on the device display screen when searching and stor-
ing.
At the end of the automatic search, the five radio stations with the strongest sig- nal are stored in the memory group for the current frequency band. 
16Audio

If some radio stations have already been stored under the station buttons, then
these station buttons will be overwritten with newly located stations after the
automatic station search.
Store station
Set the desired radio station and press and hold the corresponding key 3
» Fig. 1
on page 5 until a beep is heard. The station is stored in the device memory and its
name appears above the corresponding key
3
.

Select frequency band and radio station
Fig. 7
Main menu/selecting the frequency band
First read and observe the introductory information given on page 16.
Selecting a frequency band
The device can receive the frequencies FM (memory groupsFM1 and FM2) and AM
(memory groupsAM1 and AM2).
Pressing the RADIO button and the corresponding key
→ 3 » Fig. 1 on page 5 of
the storage group
or
repeatedly pressing the RADIO
button switches the device between each memory
group changes.
Press the menu button
2
to confirm the selected memory group.
Select radio stations
Depending on the Arrow keys » page 12 , Radio settings settings, the device sets
to a radio station in the current frequency range from the following list:
■ List of available stations
■ List of stations stored in the device memory
Briefly pressing the button 
or  switches the device to the previous or next
radio station.
Pressing and holding the button 
or  starts a search in the selected direction
and stops at the next radio station
or
turning the menu button
2
» Fig. 1 on page 5 switches the device to the previous
or next radio station.
Pressing menu button
2
selects the set station.
Five presets are available in each memory group. The station name and programme type transmitted by the radio station according
to PTY 1)
is displayed.
If the station is stored in the device memory, then the symbol 
is also displayed.
The unit will automatically search for radio stations if no list of available stations
is present.
1)
PTY (programme type) - Refers to the type of the programme transmitted by the radio station.
17Audio

The name of the artist, the album and the title of the played file can be displayed
if the information is available as a so-called ID3 tag. If no ID3 tag is available, only the folder name is displayed.
To ensure good quality sound, we recommend a minimum compressed bitrate of
160 kb/s for MP3 files. For audio files with variable bitrates, the indicated remain-
ing playback time does not correspond to the actual remaining playback time.
WMA files can only be played when not copyrighted by DRM. These kinds of WMAfiles are not supported by the device.
The more files, folders or playlists on one source, the longer it will take to read
the source. It is a good idea to create subfolders with files (e.g. by artist or album
names) in order to save time.
Source propertiesSpecifications
for USB sour-
cesUSB 1.x and 2.x or higher with support for USB 2.x
(data transfer speed then corresponds to the maximum speed of USB 2.x)
Max. speed of 480 Mb/s
File system
SD memory
cardFAT16, VFAT, FAT32, exFatUSB devicesFAT16, VFAT, FAT32CDISO9660, Joliet (Level 1,2,3), UDF 1.x, UDF 2.xSpecification
for the Blue-
tooth ®
audio
source
Profile A2DP, AVRCP
File properties
Bitratemax. 320 kb/sSampling ratemax. 48 kHz

Operation
First read and observe the introductory information and safety warn-
ings
on page 18.
The  and  buttons always affect the audio source currently being listened to,
regardless of the menu being used.
It is also possible to change tracks using the keys
3
» Fig. 1 on page 5 from with-
in the menu of the audio source currently being played.
A list of keys 3 is displayed in the menu of the audio source currently being
played after the menu button 2 is turned.
■ Play - Plays the current track
■ Up - Returns to a higher level
Press menu button 2
to start playback of the current track or to open the cur-
rent folder.
Button 
ActionFunction
Press briefly
Go to the start of the track being played if the track
has been playing for more than 3 secondsGo to the start of the previous track if the track has been playing for less than 3 secondsPress and hold buttonFast-reverse of the track
Button 
ActionFunctionPress brieflyGo to the start of the next trackPress and hold buttonFast-forward of the track
Button

/
ActionFunction
Press briefly
Play/pause: the play function is stopped at the cur-
rent position and the symbol changes to  - after re-
pressing, the play function will continue from this position.
Button 
ActionFunction
Press briefly
Go to the start of the track being played if the track
has been playing for more than 3 secondsGo to the start of the previous track if the track has been playing for less than 3 secondsPress and hold buttonFast-reverse of the track
Button 
ActionFunctionPress brieflyGo to the start of the next trackPress and hold buttonFast-forward of the track 20Audio