2013 SKODA OCTAVIA ESP

Fuses and light bulbs
Fuses
Introduction
This chapter contains information on the following subjects:
Fuses in the dash panel – LHD
252
Fuses in the dash panel – RHD
252
Assignment of the fuses in the dash panel
253
Fuses in the engine compartment
254
Assignment of fuses in the engine compartment
254
Individual electrical circuits are protected by fuses.
Switch off the ignition and the corresponding power consuming device before re-
placing a fuse.
Find out which fuse belongs to the component that is not operating » page 253,
Assignment of the fuses in the dash panel or » page 254 , Assignment of fuses in
the engine compartment .
Electrically adjustable seats are protected by automatic circuit breakers, which
switch on again automatically after a few seconds after the overload has been
eliminated.
Fuse colourMaximum amperagelight brown5dark brown7.5red10blue15yellow/blue20white25green/pink30orange/green40red50WARNINGAlways read and observe the warnings before completing any work in the en-
gine compartment » page 215.
CAUTION
■
“Never repair” fuses, and do not replace them with fuses of a higher amperage –
risk of fire! This may also cause damage at other points in the electrical system.■
If a newly inserted fuse blows again after a short time, have the electrical sys-
tem checked as quickly as possible by a specialist garage.
■
A blown fuses is recognisable by the molten metal strip. Replace the faulty fuse
with a new one of the same amperage.
■
The cover for the fuse box in the engine compartment must always be applied
correctly. Water may get into the fuse box if the cover is not replaced properly -
there is a risk of damage to the vehicle.
Note
■ We recommend always carrying replacement fuses in the vehicle. A box of re-
placement fuses can be purchased from ŠKODA Original Accessories.■
There can be several power consuming devices for one fuse.
■
There can be several consumer devices for one fuse, depending on the vehicle's
equipment.
■
Multiple fuses may exist for a single power consuming device.
■
Multiple power consuming devices can share a single fuse.

251Fuses and light bulbs

Fuses in the dash panel – LHDFig. 215
Storage compartment on the
driver's side: LHD
First read and observe the introductory information and safety warn-
ings on page 251.
On left-hand drive vehicles, the fuse box is located behind the storage compart-
ment in the left-hand section of the dash panel.
Replacing fuses
›
Open the storage compartment » page 80.
›
Grab hold of the storage compartment in the area of the arrows » Fig. 215.
›
Fold out the storage compartment by pulling in the direction of arrow
1
.
›
Remove the plastic clip under the cover of the fuse box in the engine
room » Fig. 219 on page 254 .
›
Place the clip on the respective fuse and pull this fuse out » page 253.
›
Insert a new fuse.
›
Replace the bracket at the original position.
›
Fold back the storage compartment by pressing into the secured position in the
dash panel in the direction of the arrow
2
.
›
Close the storage compartment.

Fuses in the dash panel – RHDFig. 216
Storage compartment on the front passenger's side: RHD
First read and observe the introductory information and safety warn- ings
on page 251.
On right-hand drive vehicles, the fuse box is located on the front passenger's side behind the storage compartment in the left-hand section of the dash panel.
Removing the storage compartment and replacing the fuse
›
Insert a screwdriver under the side cover » Fig. 216.
›
Unlock the cover in the direction of the arrow
1
.
›
Push the cover out in the direction of the arrow
2
.
›
Open the storage compartment.
›
Unlock the brake rod of the storage compartment in the direction of the arrow
3
with the screwdriver.
›
Remove the storage compartment in the direction of the arrow
4
.
›
Remove the plastic clip under the cover of the fuse box in the engine
room » Fig. 219 on page 254 .
›
Place the clip on the respective fuse and pull this fuse out » page 253
.
›
Insert a new fuse.
›
Replace the bracket at the original position.
Installing the storage compartment
›
Pull in the storage compartment behind the brackets
A
» Fig. 216 .
›
Push in the storage compartment in the opposite direction of the arrow
4
.
›
Insert the brake rod and lock it against the arrow
3
with a screwdriver.
›
Push in the side cover against the direction of the arrow
2
.
›
Press the side cover fully against the direction of the arrow
1
.
›
Close the storage compartment.

252Do-it-yourself

Replacing bulbs in rear light (Octavia)Fig. 231
Outer part of the light: Basic light/light with LED diodes
Fig. 232
Inner part of the light: Basic light/light with LED diodes
First read and observe the introductory information and safety warn-
ings
on page 255.
Outer part of the lamp
›
Turn the bulb holder
2
» Fig. 231 in an anti-clockwise direction and remove it
from the lamp housing.
›
Push the faulty bulb into the holder, turn in anti -clockwise direction up to the
stop and remove.
›
Insert a new bulb into the holder and turn in a clockwise direction to the the
stop.
›
Replace the holder with the bulb into the lamp housing and turn in a clockwise
direction to the stop.
Inner part of the light›Unscrew the lamp holder » Fig. 231 -  or  use the screwdriver from the car
tool kit, and remove the lamp holder from the tail light assembly.›
Turn the bulb holder anti-clockwise up to the stop and remove it from the lamp
housing » Fig. 231 -  respectively .
›
Replace the bulb, insert the holder with the bulb into the lamp housing and turn
in a clockwise direction to the stop.
›
Insert the bulb holder in the tail lamp assembly.
›
Screw on the lamp holder carefully.

260Do-it-yourself

Operating weight
The specified operating weight is for orientation purposes only. This value repre- sents the minimum operating weight without additional weight-increasing equip-ment such as air conditioning system, spare wheel, or trailer hitch.
The operating weight also contains the weight of the driver (75 kg), the weight of
the operating fluids, the tool kit, and a fuel tank filled to 90 % capacity.
It is possible to calculate the approximate loading capacity from the difference
between the permissible total weight and the operating weight »
.
The payload consists of the following components: › Passengers
› All items of luggage and other loads
› Roof load including roof rack system
› Equipment not included in the operating weight
› Trailer hook weight when towing (up to 75 kg and 80 kg for the Octavia Combi
4x4 vehicles).
Fuel consumption and CO 2 emissions according to ECE regulations and EU
directives
The measurement of the intra-urban cycle begins with a cold start of the engine. Afterwards standard urban driving is simulated.
In the extra-urban driving cycle, the vehicle is accelerated and decelerated in all
gears, corresponding to daily routine driving conditions. The driving speed varies
between 0 and -120 km/h.
The calculation of the combined fuel consumption considers a weighting of about 37 % for the intra-urban cycle and 63 % for the extra-urban cycle.
WARNINGDo not exceed the specified maximum permissible weights – risk of accident
and damage!Note■ If required, you can find out the precise weight of your vehicle at a specialist ga-
rage.■
The fuel consumption and emission values have been determined in accordance
with rules and under conditions set out by legal or technical requirements for de-
termining operational and technical data for motor vehicles.
■
Depending on the range of equipment, style of driving, traffic situation, weather
influences and vehicle condition, consumption values may deviate from the indi-
cated values.

264Technical data