2013 Seat Toledo Owner's manual

199
Wheels and tyres
The manufacturing date is also indicated on the tyre sidewall (possibly only
on the inner side of the wheel). DOT … 27 12…
means, for example, that the tyre was produced in the 27th week of 2012.
Follow the instructions ⇒ page 199 if you only have a temporary spare
wheel. 
Tyres with directional tread pattern
The direction of rotation is indicated by the arrows on the tyre sidewall. The
direction of rotation indicated must be respected. This guarantees optimum
grip and helps avoid excessive noise, wear and aquaplaning.
In the event of a flat tyre, a spare wheel with an undetermined tread pattern
or an opposite tread pattern must be used and you must drive carefully, as
in these cases the tyres no longer offer maximum performance. Spare wheel*Fig. 133 Luggage com-
partment: spare wheel
The spare wheel is housed in a well under the floor panel in the luggage
compartment and is secured by a special bolt ⇒ Fig. 133.
Take out the tool box before removing the spare wheel.
The tyre pressure of the spare wheel must be checked (preferably whenever
the tyre pressure is checked – see sticker on fuel tank flap ⇒ page 197) to
ensure the spare wheel remains ready for use.
If the spare wheel is not the same size or design as the tyres that are moun-
ted on the car (for example if the car has winter tyres or tyres with direction
tread), only use the spare tyre for a short period of time in the event of
breakdown and drive with the corresponding care ⇒ 
.
It must be replaced as soon as possible for a wheel with a normal size and
finish.
Temporary spare wheel
If the vehicle is equipped with a temporary spare wheel, there will be a
warning sign on the rim of the wheel. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

200Wheels and tyres
Follow the instructions below when driving with this wheel fitted.
● After fitting the wheel, the warning sign must not be covered.
● Do not drive faster than 80 km/h (50 mph) with this spare wheel and
take great care during the trip. Avoid heavy acceleration, hard braking and
fast cornering.
● The tyre pressure is the same as that of the standard tyres.
● Only use this spare wheel to reach the nearest Official Service, as it is
not designed for permanent use.
WARNING
● Under no circumstances must damaged spare wheels be used.
● If the spare wheel is different in size or design to the tyres currently
fitted, never drive faster than 80 km/h (50 mph). Avoid heavy accelera-
tion, hard braking and fast cornering.
CAUTION
Follow the instructions given on the temporary spare wheel label.
Note
The tyre pressure of the spare wheel must always correspond to the highest
pressure prescribed for the model of vehicle in question. 
Wheel trim
Removing
– Place the hook from the vehicle tool kit on the reinforced edge
of the wheel trim. –
Insert the box spanner through the hook, supporting it on the
tyre and remove the wheel trim.
Fitting
– First press the wheel trim onto the wheel at the cut out de-
signed for the valve. Then press the wheel trim on both sides in
the direction of the valve so that it fits correctly in place around
all the perimeter.
CAUTION
● Press down by hand, do not hit the wheel trim! Knocking it sharply, par-
ticularly at points where the wheel trim has not yet been inserted, could re-
sult in damage to the wheel trim guiding and centring elements.
● Before fitting the trim on a steel alloy wheel attached with an anti-theft
wheel bolt, make sure the bolt is in the hole in the valve area ⇒ page 211,
Anti-theft wheel bolts*.
● Where trim is fitted at a later date, ensure enough air inflow is guaran-
teed in order to cool the brake system. 
Wheel bolt caps
Fig. 134 Pull off the
wheel bolt cap 

201
Wheels and tyres
Removing
– Insert the plastic clip into the cap until the inner retaining
notches on the clips touch the collar of the cap and then re-
move ⇒ Fig. 134.
Fitting
– Insert the caps as far as they will go over the wheel bolts.
The wheel bolt caps are stored in a box on the spare wheel or in the spare
wheel well. 
Tyre pressure *
Fig. 135 Tyre pressure
setting switch
The tyre pressure monitoring system uses ABS sensors to compare the revo-
lutions and the circumference of each wheel. Should the circumference of
any wheel change, the warning lamp  in the general instrument panel
⇒ page 76 will light up and an audible warning will be heard.
Tyre circumference may change if:
● Tyre pressure is too low
● Tyre structure is damaged ●
Vehicle load not evenly distributed
● Wheels on one axle are subjected to greater load, (e.g. driving with trail-
er, uphill, downhill)
● Snow chains are fitted
● The temporary spare wheel is fitted
● One wheel on the axle has been changed
Basic system settings
Should the tyre pressure change or if one or more wheels are changed or
the position of the wheel on the vehicle is changed, e.g. changing round the
front and rear wheels, or where a warning lamp lights up when driving, the
system must be adjusted as follows:
● Inflate all tyres to the prescribed pressures ⇒ page 197.
● Switch the ignition on.
● Hold the  
⇒ Fig. 135 button down for at least 2 seconds. The warn-
ing lamp  will light up when the button is pressed. The system memory is
also deleted and a new calibration system will begin, which is indicated by
an audible warning before the warning lamp switches off .
● If the warning lamp  remains lit and does not switch off, not even once
the basic setting process is complete, this indicates a fault in the system.
Contact an Official Service.
The warning lamp  lights up
If the pressure on at least one tyre is significantly lower than the pressure
set by the driver, the warning lamp  ⇒ 
will light up.
The warning lamp  flashes
If the warning lamp flashes, there is a fault in the system. Contact a special-
ised service to have it fixed. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

202Wheels and tyres
WARNING
● If the warning lamp  lights up, slow down immediately and avoid
any severe braking or steering manoeuvres. Stop and check the tyres and
their pressure as soon as possible.
● Under certain conditions (e.g. sporty driving style, driving on loose
surfaces or in the winter) the warning lamp  may take a while to light
up or may remain switched off.
● Despite the tyre pressure monitoring system, the driver remains re-
sponsible for maintaining the correct tyre pressure. You must therefore
check the tyre pressure often.
Note
● The tyre pressure monitoring system is not a replacement for regularly
checking the tyre pressure, as it is unable to recognise an even drop in pres-
sure.
● The tyre pressure monitoring system is unable to warn of a sudden drop
in tyre pressure, e.g. a puncture. In this case, try to stop the vehicle carefully
with no severe braking or steering manoeuvres.
● To ensure the tyre pressure monitoring system works correctly, the basic
setting must be performed every 10 000 km (6000 miles) or once a year. 
Wheel bolts
The wheel bolts are matched to the rims. When installing different wheels,
e.g. to fit light alloy wheels or wheels with winter tyres, it is important to use
the correct wheel bolts with the right length and correctly shaped bolt
heads. The is essential for the secure fit of the wheels and for the proper
function of the brake system. Winter tyres
Winter tyres will significantly improve handling of the vehicle in winter road
conditions. The design of summer tyres (width, rubber compound, tread
pattern) gives less grip at temperatures below +7 °C (45 °F), on ice and
snow. This applies particularly to vehicles equipped with
wide section tyres
or high speed tyres (code letters H or V on the sidewall).
In order to preserve the performance of the vehicle as much as possible,
winter tyres must be fitted on all four wheels, the minimum depth of the
tread must be 4 mm and the maximum age must be 4 years.
You can use winter tyres of a lower speed rating if the maximum speed limit
of these tyres will not be exceeded, even if the maximum speed limit for the
vehicle is higher.
For the sake of the environment
Summer tyres should be fitted again in time, as they give better handling on
roads free of snow and ice and at temperatures over +7 °C (45 °F). Summer
tyres have a shorter braking distance, produce less rolling noise and do not
wear down as quickly. They also reduce fuel consumption. 
Snow chains
Snow chains must only be used on the front wheels.
In winter road conditions, snow chains not only help to improve grip but al-
so improve the braking capacity.
For technical reasons snow chains may only be used on tyres with the fol-
lowing wheel rim/tyre combinations. 

203
Wheels and tyres
Rim sizeRim offsetTyre size5J x 14 a)35 mm175/706J x 15b)38 mm185/606J x 15b)38 mm195/55a)
Only use snow chains with fine-pitch links and lock no greater than 9 mm.
b) Only use snow chains with fine-pitch links and lock no greater than 13 mm.
Remove the wheel trims before fitting snow chains.
CAUTION
Chains must be removed when roads are free of snow. Otherwise they will
impair handling, damage the tyres and wear out very quickly. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

204Accessories, modifications and spare parts
Accessories, modifications and spare parts
General notes
If you wish to retrofit accessories in the vehicle, or if a part of the vehicle
has been replaced by a new part or technical modifications are required, the
following instructions must be taken into account.
● Before purchasing accessories or spare parts and before making techni-
cal modifications, always request advice from an Authorised SEAT dealer
⇒ 
.
● In the event that technical modifications are carried out on the vehicle,
the instructions and regulations specified by the company, SEAT, must be
observed.
No damage will be caused to the vehicle if the established procedures are
respected, which guarantees safe driving and operation. After the modifica-
tions are carried out, the vehicle will comply with the restrictions and regu-
lations of the highway code. More information can be obtained at an Au-
thorised SEAT dealer, where all jobs required can be carried out appropriate-
ly.
Vehicle improvements and modifications
The owner must store the technical documents regarding the modifications
carried out on the vehicle to be handed over to those responsible for the
processing of the end-of-life vehicle. This ensures end-of-life processing of
the vehicle, while protecting the environment.
Work done on the electrical components and software can cause disruption
in operations. Due to the interconnection of electronic components, this
disruption can also negatively influence systems that are not directly affec-
ted. This can adversely affect reliability of the vehicle, and can produce ex-
cessive wear of the parts.
Damage caused by technical modifications that are not made with the con-
sent of SEAT will be excluded from the warranty – see warranty certificate.
WARNING
● Jobs or modifications unduly carried out on your vehicle can cause
disruption to operations - Risk of accident!
● We recommend that you use only expressly authorised SEAT Original
Accessories and ® SEAT Original Spare Parts for your vehicle. The relia-
bility, safety and compatibility with your vehicle of SEAT Original Acces-
sories and ® SEAT Original Spare Parts has been checked.
● Despite the continuous observation of the market, we cannot judge
nor guarantee the suitability of other products for your vehicle, be they
authorised products or products approved by a state testing facility.
Note
SEAT Original Accessories and ® SEAT Original Spare Parts can be pur-
chased at authorised SEAT dealers where the purchased parts can also be
fitted. 

205
Accessories, modifications and spare parts
Modifications and effects of the airbag
system
In the adjustment and modification, respect the SEAT directive.
Modifications and corrections of the front bumper, doors, front seats, roof
or bodywork must be carried out at authorised SEAT workshops. Compo-
nents of the airbag system can be found in these parts of the vehicle.
WARNING
● Airbag modules must never be repaired. They must be replaced.
● Never fit components of the airbag system removed from old vehicles
or those originating from a recycling process in the vehicle.
● The modification of the suspension of the vehicle wheels, including
the use of non-permitted combinations of tyres and rims can alter the op-
eration of the airbag system and increase the risk of serious or fatal inju-
ries in an accident.
● During all jobs on the airbag system, in addition to the removal and
fitting of parts of the system in the course of other repair jobs, parts of
the airbag system can be damaged. Therefore in the event of an accident,
this may cause the airbags to activate incorrectly or not activate al all.

Safety FirstOperating instructionsPractical TipsTechnical specifications

206Self-help
Self-help
First-aid kit and warning triangle*
Fig. 136 Location of
warning triangle
The warning triangle, measuring max. 436 x 45 x 32 mm, can be secured to
the lining on the rear of the luggage compartment with rubber straps
⇒ Fig. 136.
WARNING
The first-aid kit and fire extinguisher must be properly secured so that
they are not catapulted through the vehicle during driving and braking
manoeuvres or in the event of an accident. Risk of injury.
Note
● Observe the expiry date of the contents of the first aid kit.
● We recommend you use the first-aid kit and the warning triangle from
the SEAT Original Accessories programme available in authorised SEAT deal-
ers. Fire extinguisher*
Read the instructions given on the fire extinguisher carefully.
The fire extinguisher must be checked once a year by an authorised person
(take the applicable legal regulations into account).
WARNING
The fire extinguisher must be properly secured so that it is not catapul-
ted through the vehicle, causing injuries, during driving and braking ma-
noeuvres or in the event of an accident.
Note
● The fire extinguisher must comply with local legal requirements.
● Observe the expiry date of the fire extinguisher. The fire extinguisher
may not work properly if used after the expiry date. 