2013 RENAULT KANGOO relay

17B-121
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF721PRESE
NT OR
STOREDENGINE OVERHEATING1.DEF: Operating temperature too high.
NOTESDeal with the stored fault.
Special notes:
After this fault appears:
The Level 1 warning light is illuminated.
The overheating warning light is illuminated.
Check the engine cooling system (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19A, Cooling, Engine cooling system:
Check).
Check the coolant temperature sensor by applying TEST 15 Checking the coolant temperature sensor.
Check the correct operation of the engine cooling fans (see Test 16 Checking the fan relay).
If the fault is still present, contact the Techline.
V42_V04_DF721/V42_V05_DF721/V42_V06_DF721/V42_V14_DF721/V42_V16_DF721/V42_V18_DF721

17B-123
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF884
PRESENT OR
STOREDADDITIONAL FUEL CIRCUIT PUMP RELAYCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESConditions for application to a stored fault:
The fault is declared present after running command
AC224 Additional fuel circuit pump relay.
See the Wiring Diagrams Technical Note for Logan, Sandero, Kangoo VLL.
Check the supply of the control circuit of the additional fuel supply pump relay with a test light by running command
AC224.
Check the cleanliness and condition of the connector of the additional petrol pump relay, component code 1639
and of the injection computer connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–3ACK between components 1639 and 120,
–3FB between components 1639 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring. Otherwise replace the wiring.
Check the supply of the power circuit of the additional fuel supply pump relay with a test light by running command
AC224. If the check is correct, replace the pump, component code 1639 (see MR 388 (Logan and Sandero) or
MR 374 (Kangoo VLL), Mechanical, 19C, Tank, Fuel pump of the additional fuel tank: Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF884/V42_V05_DF884/V42_V06_DF884/V42_V14_DF884/V42_V16_DF884/V42_V18_DF884

17B-131
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF992
PRESENT OR
STOREDADDITIONAL HEATER 1 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 1 relay, component code 1067 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JU between components 1067 and 120,
–3FB between components 1067 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC250 Heating resistor 1 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1067 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF992/V42_V05_DF992/V42_V06_DF992/V42_V14_DF992/V42_V16_DF992/V42_V18_DF992

17B-132
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF993
PRESENT OR
STOREDADDITIONAL HEATER 2 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 2 relay, component code 1068 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JV between components 1068 and 120,
–3FB between components 1068 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC251 Heating resistor 2 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1068 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF993/V42_V05_DF993/V42_V06_DF993/V42_V14_DF993/V42_V16_DF993/V42_V18_DF993

17B-133
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF994
PRESENT OR
STOREDADDITIONAL HEATER 3 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 3 relay, component code 1069 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JW between components 1069 and 120,
–3FB between components 1069 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC252 Heating resistor 3 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1069 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF994/V42_V05_DF994/V42_V06_DF994/V42_V14_DF994/V42_V16_DF994/V42_V18_DF994

17B-144
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1072
PRESENT OR
STOREDAIR CONDITIONING COMPRESSOR RELAY CONTROLCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and the condition of the connector of the air conditioning compressor control relay,
component code 474 (for Logan, Sandero, Duster, Kangoo VLL) or the low speed fan assembly relay,
component code 784 (for Thalia 2/Symbol 2, Clio II F 6) and the connector of the injection computer, component
code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
For Logan, Sandero, Duster:
–38K between components 474 and 120,
–3FB between components 1047 and 474,
For Clio II F 6:
–38K between components 784 and 120,
–3FB between components 983 and 784,
For Thalia 2/Symbol 2:
–38K between components 784 and 120,
–3FB between components 238 and 784,
For Kangoo VLL:
–38K between components 474 and 120,
–3FB between components 238 and
474.
If the connection or connections are faulty and if there is a repair method (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Run command AC180 Air conditioning compressor relay control in order to check the correct operation of the
relay.
If the fault is still present, contact the Techline.
V42_V04_DF1072/V42_V05_DF1072/V42_V06_DF1072/V42_V14_DF1072/V42_V16_DF1072/V42_V18_DF1072

17B-154
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 18
DF1364
PRESENT OR
STOREDCOMPUTER AUTOMATIC SUPPLY RELAY
DEF: Inconsistent signal
NOTESNone.
See Technical Note 6520 Fault finding of the Euro V Landi Renzo LPG system. (D4F734 engine on Logan
and Sandero) or Technical Note 6524 "Landi Renzo Euro V LPG system fault finding" (K4M616 engine on
Duster).
V42_V18_DF1364

17B-161V2 MR-376-X76-17B050$100.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool status Diagnostic tool title
ET001Computer + After ignition
ET038Engine
ET039Brake pedal
ET041Gearbox ratio
ET047Fuel pump control circuit
ET051Throttle stop programming
ET089Flywheel target programming
ET148OBD warning light activation request
ET321Air conditioning compressor
ET405Clutch pedal switch
ET434Low fuel level
ET571LPG minimum signal
ET673Jammed accelerator pedal detected
ET717Target gearbox ratio
ET734Heating resistor 1 relay control
ET735Heating resistor 2 relay control
ET736Heating resistor 3 relay control
ET759Braking multiplex signal detected
ET760First starting
ET775Camshaft TDC* synchronisation
ET798Clutch wire contact connection
ET799Brake wire contact
PETROL INJECTION
Fault finding – Status summary table