2013 RENAULT KANGOO relay

17B-166V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET047FUEL PUMP CONTROL CIRCUIT
STATUS DEFINITIONACTIVE: This status indicates that the fuel pump is active.
INACTIVE: This status indicates that the fuel pump is inactive.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVEStatus ET047 is ACTIVE when starting the engine. In the event of a fault apply the
interpretation of DF085 Fuel pump relay circuit.
INACTIVEStatus ET047 is INACTIVE when the engine is stopped and the ignition off.
V42_V04_ET047/V42_V05_ET047/V42_V06_ET047/V42_V14_ET047/V42_V16_ET047/V42_V18_ET047

17B-170V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET321AIR CONDITIONING COMPRESSOR
STATUS DEFINITIONACTIVE: This status indicates that the air conditioning compressor is active.
INACTIVE: This status indicates that the air conditioning compressor is inactive
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVETo check the operation of the air conditioning, run command AC180 Air
conditioning compressor relay control. In the event of a fault, apply the
interpretation of DF1072 Air conditioning compressor control.
V42_V04_ET321/V42_V05_ET321/V42_V06_ET321/V42_V14_ET321/V42_V16_ET321/V42_V18_ET321

17B-175V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET734
ET735
ET736HEATING RESISTOR NO.1 RELAY CONTROLHEATING RESISTOR NO.2 RELAY CONTROL
HEATING RESISTOR NO.3 RELAY CONTROL
STATUS DEFINITIONACTIVE: This status indicates that the relay is supplied.
INACTIVE: This status indicates that the relay is not supplied.
Conformity check: Engine stopped, ignition on or engine running.
INACTIVEStatuses ET734, ET735 and ET736 are INACTIVE with the ignition on and the engine
stopped, or when the engine is warm.
ACTIVEStatuses ET734, ET735 and ET736 are ACTIVE when the engine is started, the
engine coolant temperature is low (< 15°C) and the air temperature is low (<5°).
This program allows the engine coolant to be heated to enable the passenger
compartment to be heated.
To control the operation of the relays, run the following commands:
AC250 Heating resistor no.1 relay.
AC251 Heating resistor no.2 relay.
AC252 Heating resistor no.3 relay.
In the event of a fault, refer to the interpretation of faults:
DF992 Additional heater relay 1 circuit.
DF993 Additional heater relay 2 circuit.
DF994 Additional heater relay 3 circuit.
V42_V04_ET734/V42_V05_ET734/V42_V06_ET734/V42_V04_ET735/V42_V05_ET735/V42_V06_ET735/V42_V04_ET736/V42_V05_ET736/
V42_V06_ET736/V42_V14_ET734/V42_V14_ET735/V42_V14_ET736/V42_V16_ET734/V42_V16_ET735/V42_V16_ET736/V42_V18_ET734/
V42_V18_ET735/V42_V18_ET736

17B-212
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$130.mif
PETROL INJECTION
Fault finding – Interpretation of parameters17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
PR814NUMBER OF ACTIVE HEATING RESISTORS
PA R A M E T E R
DEFINITIONThis parameter indicates the number of active heating resistors and can be between 0
to 5 depending on the relays activated.
0 if no relay is active
1 if relay 1 is active
2 if relay 2 is active
3 if relays 1 and 2 are active
4 if relays 2 and 3 are active
5 if all of the relays are active
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature < 80°C
In the event of a fault, consult the interpretation of faults:
DF992 Additional heater relay 1 circuit,
DF993 Additional heater relay 2 circuit,
DF994 Additional heater relay 3 circuit.
V42_V04_PR814/V42_V05_PR814/V42_V06_PR814/V42_V14_PR814/V42_V16_PR814/V42_V18_PR814

17B-213V2 MR-376-X76-17B050$140.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*TDC: Top Dead Centre
**GMV: fan assemblyTool
commandDiagnostic tool title Comments
RZ001 Fault memoryThis command is used to clear the faults stored in the computer.
RZ003 Engine adaptivesThis command enables a long engine start time.
RZ031 Throttle stop programmingThis command is used to reset the necessary system adaptives
if replacing the throttle valve.
RZ033Richness regulation
programmingThis command is used to reset the necessary system adaptives
if replacing the injectors.
RZ037Flywheel target
programmingThis command is used to reset the necessary system adaptives
if replacing the TDC* sensor.
RZ064Programming the level of
alcoholThis command is used to count the richness adaptive
programming necessary when replacing the injection computer.
AC005 Cylinder 1 injectorThis command is used to perform an audible check on injector 1.
AC006 Cylinder 2 injectorThis command is used to perform an audible check on injector 2.
AC007 Cylinder 3 injectorThis command is used to perform an audible check on injector 3.
AC008 Cylinder 4 injectorThis command is used to perform an audible check on injector 4.
AC015 Fuel pump relayThis command is used to check the fuel pump.
AC017Canister bleed solenoid
valveThis command is used to check the canister bleed solenoid
valve.
AC027 Motorised throttleThis command is used to check the motorised throttle.
AC038 Low speed GMV** relayThis command is used to check the low speed GMV** relay.
AC039 High speed GMV** relayThis command is used to check the high speed GMV** relay.
AC180Air conditioning
compressor relay controlThis command is used to check the air conditioning compressor
relay.
PETROL INJECTION
Fault finding – Command summary table

17B-214V2 MR-376-X76-17B050$140.mif
PETROL INJECTION
Fault finding – Command summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AC217Additional fuel circuit
solenoid valveThis command is used to check the additional fuel circuit
solenoid valve. Only on Flexfuel injection
AC224Additional fuel circuit pump
relay This command is used to check the relay of the additional circuit
pump. Only on Flexfuel injection
AC250 Heating resistor 1 relayThis command is used to activate the heating resistor no.1 relay.
AC251 Heating resistor 2 relayThis command is used to activate the heating resistor no.2 relay.
AC252 Heating resistor 3 relayThis command is used to activate the heating resistor no.3 relay.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data has been saved using command SC003).
SC003 Save computer dataThis command enables the computer operating data, the engine
adaptives, to be recorded.
SC006Start OBD test: Catalytic
converterThis command is used to test the catalytic converter.
SC007 Run OBD test: O2 sensorThis command is used to test the O2 sensors.
SC061Oil change interval (OCS)
OxidationThis command is used to perform a test on the oil oxidation (see
Technical Note 6523A, Oil change interval (OCS) fault finding
for petrol and diesel engines)
VP010 Enter VIN.This command is used to enter the VIN.
VP036 Fuel supply inhibitedThis command is used to inhibit fuel supply to the engine.

17B-223
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 4 Fuel leak
Check the fuel pump relay by running TEST 1 Fuel supply pump relay check.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
If the fault is still present, contact the techline.
V42_V04_ALP4 /V42_V05_ALP4/V42_V06_ALP4/V42_V14_ALP4/V42_V16_ALP4/V42_V18_ALP4

17B-235
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 16 Impossible to start the engine
Check the fuel pump relay by running TEST 1 Petrol supply pump relay check.
Check the air filter unit.
Check the oil.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the spark plugs.
Check the injector rail.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the TDC sensor by running TEST 10 TDC sensor check.
Check the coolant pump.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the rotating parts.
Check the accessories belt.
Check the supply relay and the injection computer.
If the fault is still present, contact the techline.
V42_V04_ALP16/V42_V05_ALP16/V42_V06_ALP16/V42_V14_ALP16/V42_V16_ALP16/V42_V18_ALP16