2013 RENAULT KANGOO fuel

17B-23
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF011
PRESENT OR
STOREDSENSOR FEED VOLTAGE NO. 11.DEF: Above maximum threshold.
2.DEF: Below minimum threshold.
NOTESSpecial notes:
– The OBD and Level 2 warning lights illuminate.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Disconnect the accelerator pedal sensor gang 1, component code 921 then switch on the ignition. Wait several
seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the accelerator pedal sensor gang 1, component code 921
(see MR 388 (Logan and Sandero), MR 451 (Duster) MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR
374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls, Accelerator pedal: Removal -
Refitting).
Disconnect the motorised throttle valve, component code 1076 then switch on the ignition (see MR 388 (Logan
and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting).
Wait several seconds so that the computer can update the fault status.
If the fault changes from present to stored: Replace the damper valve position sensor, component code 1076, (see
MR 388 (Logan and Sandero), MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR
374 (Kangoo VLL), Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting) referring to the
Replacement of components section.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LR between components 921 and 120,
–3LT between components 921 and 120,
–3MN between components 1076 and 120,
–3MO between components 1076 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
V42_V04_DF011/ V42_V05_DF011/V42_V06_DF011/V42_V14_DF011/V42_V16_DF011/V42_V18_DF011

17B-28
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF026
PRESENT OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 1 injector, component code 193.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 1 injector, component code 193 between connections 3FB and 3CR.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 1 injector,
component code 193 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
V42_V04_DF026/ V42_V05_DF026/V42_V06_DF026/V42_V14_DF026/V42_V16_DF026/V42_V18_DF026

17B-30
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF027
PRESENT OR
STOREDINJECTOR CYLINDER 2 CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 2 injector, component code 194.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 2 injector, component code 194 between connections 3FB and 3CS.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 2 injector,
component code 194 (see MR 388, (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC006 Cylinder 2 injector and check the operation of the injector with a listening test.
V42_V04_DF027/ V42_V05_DF027/V42_V06_DF027/V42_V14_DF027/V42_V16_DF027/V42_V18_DF027

17B-32
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF028
PRESENT OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 3 injector, component code 195.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 3 injector, component code 195 between connections 3FB and 3CT.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 3 injector,
component code 195 (see MR 388, (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting).
Run command
AC007 Cylinder 3 injector and check the operation of the injector with a listening test.
V42_V04_DF028/ V42_V05_DF028/V42_V06_DF028/V42_V14_DF028/V42_V16_DF028/V42_V18_DF028

17B-34
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF029
PRESENT OR
STOREDCYLINDER 4 INJECTOR CONTROL CIRCUITCO: Open circuit.
CC.1: Short-circuit on +12 volts.
CC.0: Short circuit to earth
NOTESThe fault changes from stored to present when the engine is running at idle
speed.
Special notes:
For CC.1 and CO, the OBD and Level 1 warning lights illuminate.
For CC.0, the Level 2 warning light illuminates.
Measure the resistance of the injector between 0°C and 40°C.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the injection computer, component code 120 and of the
cylinder 4 injector, component code 196.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the cylinder 4 injector, component code196 between connections3FB and 3CU.
If the resistance measured is not between 11   X  20  (K4M, D4D engines), 11.5   X  12.5  (F4R engine),
9.2   X  17  (K7M engine) or 14   X  15  (K4M engine on Duster): replace the cylinder 4 injector,
component code 196 (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply, Injector rail -
Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), MR 374
(Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting
).
Run command AC008 Cylinder 4 injector and check the operation of the injector with a listening test.
V42_V04_DF029/ V42_V05_DF029/V42_V06_DF029/V42_V14_DF029/V42_V16_DF029/V42_V18_DF029

17B-41
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF059
PRESENT OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
NOTESPriority when dealing with a number of faults:
– DF109 Low fuel level misfire,
Check whether there are other cylinders with a combustion misfire fault reported by
the diagnostic tool before starting the fault finding procedure below.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
– engine running at idling speed.
Special note:
OBD warning light comes on.
1.DEF
NOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 1 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 1.
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter: Removal - Refitting).
V42_V04_DF059/ V42_V05_DF059/V42_V06_DF059/V42_V14_DF059/V42_V16_DF059/V42_V18_DF059

17B-42
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF059
CONTINUED
2.DEFNOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit
Check the condition of the cylinder 1 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 1.

17B-43
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF060
PRESENT
OR STOREDMISFIRING ON CYLINDER 2
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
NOTESPriority when dealing with a number of faults:
– DF109 Low fuel level misfire,
Check whether there are other cylinders with a combustion misfire fault reported by
the diagnostic tool before starting the fault finding procedure below.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
– engine running at idling speed.
Special note:
OBD warning light comes on.
1.DEF
NOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 2 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 2.
V42_V04_DF060/ V42_V05_DF060/V42_V06_DF060/V42_V14_DF060/V42_V16_DF060/V42_V18_DF060