2013 RENAULT KANGOO engine

17B-164V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET038ENGINE
STATUS DEFINITIONSTOPPED: This status indicates that the engine ignition is on without the starter
engaged.
STALLED: This status indicates that the engine has stalled.
RUNNING: This status indicates that the engine has started.
STARTING: This status indicates that the engine is in starting phase.
V42_V04_ET038/V42_V05_ET038/V42_V06_ET038/V42_V14_ET038/V42_V16_ET038/V42_V18_ET038

17B-166V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET047FUEL PUMP CONTROL CIRCUIT
STATUS DEFINITIONACTIVE: This status indicates that the fuel pump is active.
INACTIVE: This status indicates that the fuel pump is inactive.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVEStatus ET047 is ACTIVE when starting the engine. In the event of a fault apply the
interpretation of DF085 Fuel pump relay circuit.
INACTIVEStatus ET047 is INACTIVE when the engine is stopped and the ignition off.
V42_V04_ET047/V42_V05_ET047/V42_V06_ET047/V42_V14_ET047/V42_V16_ET047/V42_V18_ET047

17B-167V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET051THROTTLE STOP PROGRAMMING
STATUS DEFINITIONCOMPLETED: This status indicates that the throttle stops have been programmed
NOT COMPLETED: This status indicates that the throttle stops have not been
programmed.
Conformity check: Engine stopped, ignition on or engine running.
COMPLETEDThis means that the throttle stops have been programmed.
Even though this programming is automatic, take particular care when performing the
first motorised throttle stop programming operation.
This can be carried out on several occasions:
– when a computer is switched on for the first time,
– at the end of computer programming (see Replacement of components)
The air temperature must be above 0°C during programming, then, at the end of
programming, switch off the ignition and wait 30 seconds for the end of Power Latch
so that the computer can store the programmed stops.
NOT
COMPLETEDThis means that the throttle stops have not been programmed.
V42_V04_ET051/V42_V05_ET051/V42_V06_ET051/V42_V14_ET051/V42_V16_ET051/V42_V18_ET051

17B-168V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET089PROGRAMMING THE ENGINE FLYWHEEL TARGET
STATUS DEFINITIONCOMPLETED: This status indicates that the throttle stops have been programmed
NOT COMPLETED: This status indicates that the throttle stops have not been
programmed.
Conformity check: Engine stopped, ignition on or engine running.
COMPLETEDThis means that the engine flywheel target programming has been completed.
In the event of a fault, program the engine flywheel target (seeReplacement of
components).
In the event of a fault, apply the interpretation of DF457 Flywheel target.
NOT
COMPLETEDThis means that the engine flywheel target programming has not been completed.
V42_V04_ET089/V42_V05_ET089/V42_V06_ET089/V42_V14_ET089/V42_V16_ET089/V42_V18_ET089

17B-169V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET148OBD WARNING LIGHT ACTIVATION REQUEST
STATUS DEFINITIONYES: This status indicates that the warning light is lit continuously.
NO: This status indicates that the warning light is off.
FLASHING: This status indicates that the warning light flashes.
SELF TEST: This status indicates that the warning light is performing a self test.
NOTESSpecial notes:
In the event of normal operation, this warning light must remain off (NO).
Conformity check: Engine stopped, ignition on or engine running.
"YES"If the status is inconsistent, consult the interpretation of fault DF342 Malfunction
indicator light circuit.
V42_V04_ET148/V42_V05_ET148/V42_V06_ET148/V42_V14_ET148/V42_V16_ET148/V42_V18_ET148

17B-170V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET321AIR CONDITIONING COMPRESSOR
STATUS DEFINITIONACTIVE: This status indicates that the air conditioning compressor is active.
INACTIVE: This status indicates that the air conditioning compressor is inactive
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Conformity check: Engine stopped, ignition on or engine running.
ACTIVETo check the operation of the air conditioning, run command AC180 Air
conditioning compressor relay control. In the event of a fault, apply the
interpretation of DF1072 Air conditioning compressor control.
V42_V04_ET321/V42_V05_ET321/V42_V06_ET321/V42_V14_ET321/V42_V16_ET321/V42_V18_ET321

17B-171V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405CLUTCH PEDAL SWITCH
STATUS DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial notes:
Apply the checks only if statuses ACTIVE and INACTIVE are inconsistent
with the pedal position.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant temperature >
80°C.
INACTIVECheck the condition and fitting of the clutch pedal position sensor, component
code
675 (see MR 388 (Logan and Sandero), Mechanical, 37A, Mechanical
component controls, Clutch pedal position sensor: Removal - Refitting or MR
451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical,
37A, Mechanical component controls, Clutch pedal: Removal - Refitting).
Remove the clutch pedal position sensor, component code 675 (see MR 388
(Logan and Sandero), Mechanical, 37A, Mechanical component controls,
Clutch pedal position sensor: Removal - Refitting or MR 451 (Duster) or MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6), Mechanical, 37A, Mechanical
component controls, Clutch pedal: Removal - Refitting).
Check the insulation between connections MAM (for Logan, Sandero, Duster) or
M (for Thalia 2/Symbol 2, Clio II F 6) and 86D of component 675 with the switch in
the rest position.
– Repeat this operation with the switch pressed, and check the continuity and the
absence of interference resistance between the two connections.
If these 2 checks are not correct, replace the clutch pedal position sensor,
component code 675 (see MR 388 (Logan and Sandero), Mechanical, 37A,
Mechanical component controls, Clutch pedal position sensor: Removal -
Refitting or MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6),
Mechanical, 37A, Mechanical component controls, Clutch pedal: Removal -
Refitting).
V42_V04_ET405/V42_V05_ET405/V42_V06_ET405/V42_V14_ET405/V42_V16_ET405/V42_V18_ET405

17B-173V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET673JAMMED ACCELERATOR PEDAL
STATUS DEFINITIONYES: This status indicates that the accelerator pedal is jammed.
NO: This status indicates that the accelerator pedal is not jammed.
NOTESTo reinitialise this status, clear the fault memory by running command RZ001 Fault
memory.
Conformity check: Engine stopped, ignition on or engine running.
YESCheck that the accelerator pedal is not jammed or that there is nothing impeding its
operation (floor carpet, etc.).
Check the brake switch (see the interpretation of fault DF050 Brake switch circuit.
V42_V04_ET673/V42_V05_ET673/V42_V06_ET673/V42_V14_ET673/V42_V16_ET673/V42_V18_ET673