2013 RENAULT KANGOO engine oil

17B-4V2 MR-376-X76-17B050$020.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Injection computer:
The injection computer is located in the engine compartment, behind the battery.
TDC sensor:
This sensor is located on the gearbox casing, behind the engine.
Pinking sensor:
This sensor is located between the four injectors.
Refrigerant pressure sensor:
This sensor is located on the air conditioning circuit.
Injection coolant temperature sensor:
This sensor is located on the engine water chamber.
Injection air temperature sensor:
The air temperature sensor is located at the air circuit inlet.
Downstream oxygen sensor:
The downstream oxygen sensor is located on the exhaust pipe downstream of the catalytic converter.
Upstream oxygen sensor:
The upstream oxygen sensor is located on the exhaust pipe after the manifold.
Accelerator potentiometer:
The potentiometer is located on the accelerator pedal.
Brake light switch:
The switch is located on the brake pedal.
Injectors 1, 2, 3, 4:
The injectors are mounted on the engine.
Motorised throttle valve:
The damper valve is located in front of the inlet manifold.
Quadruple ignition coil module (D4D and K7M engines):
The coil module is located in the engine compartment.
Cylinder 1, 2, 3, 4 pencil coils (K4M engine):
They are located on the cylinder head.
Catalytic converter:
The catalytic converter is located on the exhaust pipe downstream of the catalytic pre-converter.
Fan unit relay:
The relay is located on the cooling radiator.
PETROL INJECTION
Fault finding – List and location of components

17B-6V2 MR-376-X76-17B050$030.mif
PETROL INJECTION
Fault finding – Role of components17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Motorised throttle valve:
The throttle valve allows engine air flow to be managed according to driver requests.
Quadruple ignition coil module (D4D and K7M engines):
The ignition unit enables ignition (explosion timing control).
Cylinder 1, 2, 3, 4 pencil coils (K4M engine):
The pencil coils enable ignition (explosion timing control).
Fan unit relay:
The engine cooling fan unit relay supplies power to the engine cooling fan.
Camshaft dephaser (F4R engine):
The function of the camshaft dephaser (VVT) is to vary the camshaft adjustment.
The system consists of a dephaser (hydraulic part that modifies the camshaft adjustment) and a solenoid valve.

17B-7V2 MR-376-X76-17B050$040.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
For flex-fuel engines
1. Air filter
2. Motorised throttle valve
3. Injection air temperature sensor
4. Manifold pressure
5. Injectors
6. Ignition coils
7. Injection coolant temperature sensor
8. Pinking sensor
9. TDC sensor
10. Upstream oxygen sensors
11. Downstream oxygen sensors
12. Injection computer
13. Auxiliary cold starting system
14. Auxiliary fuel tank
15. Auxiliary fuel
16. Petrol/alcohol tank
17. Petrol pump
18. Bleed valve
PETROL INJECTION
Fault finding – Operating diagram

17B-8V2 MR-376-X76-17B050$040.mif
PETROL INJECTION
Fault finding – Operating diagram17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
For petrol and bio-petrol engines
1. Air filter
2. Motorised throttle valve
3. Injection air temperature sensor
4. Manifold pressure
5. Injectors
6. Ignition coils
7. Injection coolant temperature sensor
8. Pinking sensor
9. TDC sensor
10. Upstream oxygen sensors
11. Downstream oxygen sensors
12. Injection computer
13. Petrol tank
14. Petrol pump
15. Bleed valve

17B-17V2 MR-376-X76-17B050$070.mif
PETROL INJECTION
Fault finding – Fault summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
*Info: InformationTool fault DTC code Diagnostic tool title
DF0810443 Canister bleed solenoid valve circuit
DF0820135 Upstream oxygen sensor heating circuit
DF0830141 Downstream oxygen sensor heating circuit
DF0850627 Fuel pump relay control circuit
DF0880325 Pinking sensor circuit
DF0910500 Vehicle speed signal
DF0920130 Upstream oxygen sensor circuit
DF0930136 Downstream oxygen sensor circuit
DF0950120 Throttle potentiometer circuit gang1
DF0960220 Throttle potentiometer circuit gang 2
DF101C121 ESP multiplex connection
DF1022503 Available alternator power sig.*
DF108C108 LPG/CNG computer multiplex connection
DF1090313 Low fuel level misfire
DF1200335 Engine speed sensor signal
DF1950016 Camshaft sensor / engine speed consistency
DF3190340 Camshaft sensor circuit
DF3420650 Malfunction indicator light circuit
DF3581608 Injector control computer
DF3611351 Ignition coil circuit 1-4
DF3621352 Ignition coil 2-3 circuit
DF3630011 Camshaft dephaser
DF37910A4 Cylinder injector 1 control

17B-41
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF059
PRESENT OR
STOREDCOMBUSTION MISFIRES ON CYLINDER 1
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
NOTESPriority when dealing with a number of faults:
– DF109 Low fuel level misfire,
Check whether there are other cylinders with a combustion misfire fault reported by
the diagnostic tool before starting the fault finding procedure below.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
– engine running at idling speed.
Special note:
OBD warning light comes on.
1.DEF
NOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 1 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 1.
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter: Removal - Refitting).
V42_V04_DF059/ V42_V05_DF059/V42_V06_DF059/V42_V14_DF059/V42_V16_DF059/V42_V18_DF059

17B-43
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF060
PRESENT
OR STOREDMISFIRING ON CYLINDER 2
1.DEF: Polluting misfiring
2.DEF: Destructive misfiring
NOTESPriority when dealing with a number of faults:
– DF109 Low fuel level misfire,
Check whether there are other cylinders with a combustion misfire fault reported by
the diagnostic tool before starting the fault finding procedure below.
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
– engine running at idling speed.
Special note:
OBD warning light comes on.
1.DEF
NOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 2 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster) or MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II
F 6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 2.
V42_V04_DF060/ V42_V05_DF060/V42_V06_DF060/V42_V14_DF060/V42_V16_DF060/V42_V18_DF060

17B-44
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$081.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF060
CONTINUED
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
do not touch the accelerator pedal or clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic converter: Removal - Refitting).
2.DEF
NOTESNone.
Check the ignition coil circuit (see MR 388, Mechanical, 17A, Ignition, Ignition: Specifications),
Check the fuel supply circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol
2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating
diagram),
Check the fuel supply pump circuit (see MR 388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit:
Operating diagram),
Check the condition of the cylinder 2 injector (see MR 388 (Logan and Sandero), Mechanical, 13A, Fuel supply,
Injector rail - Injectors: Removal - Refitting, MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F
6), MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal - Refitting),
Check the compression of cylinder 2.