2013 Peugeot 508 RXH engine

124
Driving
With the ignition on or the hybrid system active,
to release the parking brake, pressthe brakepedal, pull
then release control lever A.
The full release of the parking brake is confirmed by:
Manual release
- the braking warning lamp and of
the P warning lamp in the controllever A
going off,
- displa
y of a message.
I
f you pull the control lever Awithout pressing
the brake pedal, the parking brake will not
be released and a message appears in the
instrument panel. If necessar
y, you can make a maximum
applicationof the parking brake. It is obtained by means of a long pullon control lever A,
until you see a message and an audible signal is heard.Maximum application is essential:


- in the case of a vehicle towing a trailer,
if the automatic functions are activatedbut you are applying the parking brake
manually,

- when the slope you are parked on mayvary (e.g. on a ferry, on a lorry, during
towing).
Maximum application


Before leaving the vehicle, check that parking brake warning lamps in the instrument panel and in the control lever Aare on fixed (not flashing).

Never leave a child alone inside thevehicle with the ignition on, as they could release the parking brake.



Automatic application,
engine off



- illumination of the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
With the vehicle stationary, the parking brake is automatically applied when the engine is
switched off. The application of the parking brake is confirmed by:
In the case of towing, a loaded vehicleor parking on a gradient, make amaximum application of the parkingbrake then turn the front wheels towards the pavement and engage a gear whenyou park.
After a maximum application, the release time will be longer.

4
125
Driving

Automatic release

The electric parking brake releases automatically and progressively with the
movement of the vehicle,select position A, Mor Rthen press the accelerator.
Full release of the parking brake is confirmed by:
- the brakin
g warning lamp and of
the Pwarning lamp in the control lever A
going off,
- displa
y of a message.


When stationary, with the hybrid system active, do not press the accelerator pedal unnecessarily, as you may release the parking brake.
Before leaving the vehicle, check thatparking brake warning lamps in theinstrument panel and the control lever Aare on fixed, not flashing.


Immobilising the vehicle,
hybrid system active
With the hybrid system active and the vehicle
stationary, in order to immobilise the vehicle it is essential to manually
apply the parking
brake by pulling
control lever A.
The application of the parking brake is confirmed by:


- illumination o
f the braking warning
lamp and of the Pwarning lamp in
the control lever A ,

- displa
y of a message.
When the driver’s door is opened, a loud beep
is heard and a message is displayed if theparking brake has not been applied.
Particular situations

In cer tain situations (e.g. star ting the engine),
the parking brake can automatically alter itsforce. This is normal operation.
To advance your vehicle a few centimetres
without star ting the engine, but with the ignition on, press on the brake pedal and release the
parking brake by pushing then releasingcontrol lever A
. The full release of the parking
brake is confirmed by the warning lamps in
the control lever Aand in the instrument panel going off and display of a message.
If a parking brake fault occurs while appliedor
if the battery runs flat, an emergency release is
always possible.
In order to ensure correct operation and
so your safety, the number of successive
application/release operations of the parkin
g
brake is limited to eight.
In the event of abuse, you are aler ted by a
message and a warning lamp which flashes.

4
129
Driving
SituationsConsequences
To a p p ly the electric parking brake: )
immobilise the vehicle and switch off the ignition. )
pull the control for at least 5 seconds or until application is complete.
)
switch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than during normal operation.
To release the electric parking brake:) switch on the ignition. )
push the control lever and hold it for approximately 3 seconds then
release it.
If the braking warning lamp is flashing or if the warning lamps do not come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a PEUGEOT dealer or aqualified workshop.

and possibl
y

flashing
Display of the message "Parking brake fault" and of the following warning lamps:
- Only the automatic application on switching off the engine andautomatic release on acceleration functions are available.


- The manual application/release of the electric parking brake and theemergency braking are not available.
and possibly


flashing

Display of the message "Battery charge fault".

- You must stop as soon as it is safe to do so. Switch off and
immobilise your vehicle (if necessary, place the a chock under a
wheel).

- Apply the electric parking brake before switching off the engine.

4
131
Driving

Engagement of reverse gear isaccompanied by an audible signal.
If you leave the vehicle, place the gear
selector in position Nand then you must stop the hybrid system by switching off the ignition (Ready
lamp off).
If the gear selector is not in position Non starting, Nflashes in the instrumentpanel, accompanied by an audiblesignal and a message in the instrument panel screen. Foot on brakeflashes on the instrument panel, accompanied by anaudible signal and a message in the instrument panel screen, if the brakepedal is not pressed on starting.


For optimum acceleration, for example
when overtaking another vehicle, pressthe accelerator pedal firmly past the point of resistance.


Displays in the instrument panel
N Neutral
R Reverse1, 2, 3, 4, 5, 6
Gears in manual mode A This comes on when automated mode is selected. It goes off on changing to manualmode.
)Place your foot on the brakewhen a message appears in the
instrument panel screen.

Moving off
)
Select position N . )
Press the brake pedal down fully. )
Star t the hybrid system.
Nappears in the instrument panelscreen.
)
Select a gear (position M
or A
) or reverse A(position R).R)
Release the parking brake unless it is
programmed to automatic mode. ) Ta k e your foot off the brake pedal, thenaccelerate.
Aand 1or R
appear in the instrumentpanel screen.


Automatic mode
)
After star ting the vehicle, select position Afor enter automatic mode.
Aappears in the instrument panel screen.A

The gearbox is then operating in auto-active
mode, without any action on the par t of the driver. It continuously selects the most suitablegear, depending on the:


- st
yle of driving,

- profile of the road.


When the engine is idling with thebrakes off, if position R, Aor M
is selected, the vehicle will move off
on its own without any action on theaccelerator.

132
Driving
Manual gear changing
) When the vehicle has moved off, select
position M to change to manual mode.)
Operate the +
or -steering mounted control paddles.


At very low speed, if reverse gear isrequested, this will only be taken intoaccount when the vehicle is immobilised(foot on the brake). A warning lamp appears in the instrument panel screen.

On sharp acceleration in manual mode,the gearbox will not change up unless the driver acts on the gear lever or thesteering mounted paddles.
Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised with the brakepedal pressed.
Adisappears and the gears engaged
appear successively in the instrumentpanel screen.

The
gear change commands are only carried
out if the engine speed permits. The internal combustion engine is still running.
It is not necessary to release the accelerator
during gear changes.
When brakin
g or slowing down, the gearbox changes down automatically to permit
acceleration in the correct gear. This selective
gear change mode enables you
to over take, for example, while still remaining in automatic mode.)Operate the +or - steering mounted controlpaddle.
The gearbox engages the gear requested if theengine speed permits. A is still displayed in theinstrument panel.
After a few moments without any action on
the controls, the gearbox resumes automatic control of the gears.

Manual mode

4
133
Driving
You must press the brake pedal when star ting the engine.
Whatever the circumstances, you mustmanually apply the parking brake when parking, unless the parking brake is programmed in automatic mode.

When immobilising the vehicle, with the hybrid system active, you must place the gear selector in neutral N
.Before carrying out any work in the engine compar tment, check that the gear selector is in neutral N
and that the
parking brake is applied.

Stopping the vehicle
With the ignition on, theflashing of this warning lamp,
accompanied by an audible
signal and a message in the instrument panelscreen, indicates a malfunction of the gearbox.
Have it checked by a PEUGEOT dealer or a qualified workshop. Be
fore switching off the engine, you can
choose to:
- move to position N
to engage neutral,
- leave the gear engaged; in this case, it will
not be possible to move the vehicle.
In both cases,
you should apply the parking brake to immobilise the vehicle.

Operating fault

This function facilitates manoeuvring of the
vehicle at low speed (when parking, in traffic jams, …).
With the hybrid system active and the parkingbrake released, if position A
, M
or Risselected, the vehicle moves as soon as you
take your foot off the brake pedal (even without
any action on the accelerator).

Creep function (moving
without the accelerator
)

Never leave children unsuper vised in the vehicle with the hybrid system active.

For
your safety, this function will only be
activated if you press the brake pedal when engaging for ward drive or reverse.
This function is deactivated if the driver's door
is opened. To reactivate it, close the door and
then press the brake or accelerator pedal.

136
Driving
)With the engine running, press button 1 toactivate the system and deploy the strip. )Press and hold button 2
to deactivate the
system and retract the strip.
The activated/deactivated state is saved and restored on restar ting the engine.
Activation / Deactivation
) With the engine running, adjust the
brightness of the information displayedusing buttons 3 :


- the "sun" to increase the brightness,

- the "moon" to decrease the brightness.





Brightness adjustment


We recommend that adjustments are made using these buttons only when the vehicle is stationary. When stationary or while driving, no objects
should be placed around the strip (or in itsrecess) so as to not impede deployment of the strip and its correct operation.


In certain extreme weather conditions (rain and/or snow, bright sunshine, ...) the head-up display may not be legibleor may suffer temporary interference. Some sunglasses may hamper readingof the information.
To clean the strip, use a clean, soft cloth (such as a spectacles cloth or microfibre cloth). Do not use a dry or abrasive cloth or detergent or solventproducts as these could scratch thestrip or damage the non-reflectivecoating.

Height adjustment
)With the engine running, adjust the display
to the desired height using buttons 4 :
- up to move the display up,
- down to move the display down.

5
149
Visibility
An audible signal when a front door is opened warns the driver that the vehicle's exterior lighting is on, with theignition off and in manual lighting mode. In this case, switching off the lighting stops the audible signal.
With the ignition off, if the dipped headlamps remain on, the vehicle goes into "ECO" mode to avoid discharging the battery.

In some weather conditions (e.g. low temperature or humidity), the presence of misting on the internal sur face of theglass of the headlamps and rear lampsis normal; it disappears after the lamps have been on for a few minutes.

Daytime lighting, compulsory in cer tain
countries, which comes on automatically when
the engine is star ted making the vehicle more
visible to other road users.
Daytime running lamps

This function is assured:


- in countries where it is imposed by
regulations, by illumination of the dippedbeam headlamps with the sidelamps and number plate lamps.

- for other countries where it is provided, by
the use of dedicated lamps.

This function can be activatedor deactivated via the vehicleconfiguration menu.



The lighting goes off when you switchoff the ignition, but you can always switch it on again using the lighting control stalk.
*
f
unction that can be set in the vehicle
configuration menu.
LED lamps
They come on when the engine is started.Depending on the destination country, they are used for:
- daytime running lamps *
in day mode andsidelamps in night mode (they are brighter
when daytime running lamps),
or
- sidelamps in day and night mode.
Where LED lamps are fitted, the filament bulbs
for the da
ytime running lamps / sidelamps in
the front lamp units are not used.