2013 Peugeot 208 Owner's Manual

47
2
Access

Electronic engine immobiliser

The key contains an electronic chip which has
a special code. When the ignition is switched on, this code must be recognised in order for starting to be possible.
This electronic engine immobiliser locks theengine management system a few minutes
after the ignition is switched off and preventsstar ting of the engine by anyone who does not
have the key.
) Press the closed padlock to locate your locked vehicle in acar park.
Locating your vehicle

This is indicated by lighting of the cour tesy
lamps and flashing of the direction indicators
for a few seconds.
Guide-me-home
lighting
Make a long press this button to
operate the guide-me-home lighting (switching on the sidelamps, dipped
beams and number plate lamps).
A second
press before the end of the timed period cancels the guide-me-home lighting.
Anti-theft protection
In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal and a message
in th
e screen.
In this case, your vehicle will not start; contact
a PEUGEOT dealer as soon as possible.
Keep safely the label attached to the keys given to you on acquisition of thevehicle.

48
Access
Locking / unlocking from the inside
)Press the switch.This allows the doors and the boot to be locked or unlocked.


Driving with the doors locked may makeaccess to the passenger compartmentby the emergency services moredifficult in an emergency.

If one of the doors is open, the doorsare not locked.
When locking / deadlocking fromoutsideWhen the vehicle is locked or deadlocked from outside, the switchdoes not operate. )After normal locking, pull theinterior door lever to unlock the vehicle. )After deadlocking, you have to use
the remote control or the key to unlock the vehicle.


Automatic central locking of the doors

The doors can lock automatically while driving (speed above 6 mph [10 km/h]).
To turn this function on or off (on by default). )press and hold the button until there is anaudible signal and/or a message in the
screen.

49
2
Access
Secondary control
doors in the event of a fault with the central
locking system or a battery failure.


Driver's door

Inser t the key in the lock to lock or unlock the door.


Passenger doors
)On the rear doors, check that the child lock
is not on.)Remove the black cap located on the edge
of the door, using the key. )Inser t the key into the aper ture without forcing, then without turning, move the
latch sideways towards the inside of thedoor.
)Remove the key and refit the cap.




Changing the battery

Battery ref.: CR1620 / 3 volts.
Do not throw the remote control batteries away, they contain metalswhich are harmful to the environment.
Take them to an approved collectionpoint.
Remote control problem
Reinitialisation
)
Switch off the ignition.)
Turn the key to position 2 (Ignition).)
Press the closed padlock immediately for a
few seconds.) Switch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again. Followin
g disconnection of the vehicle battery,replacement of the remote control battery or in the event of a remote control malfunction, you can no longer unlock, lock or locate your
vehicle.) First of all, use the key in the lock to unlock
or lock your vehicle.) Then, reinitialise the remote control.
I
f the problem persists, contact a PEUGEOT
dealer as soon as possible.
If the batter
y is flat, you are informed
by lighting of this warning lamp in the
instrument panel, an audible signal
and a message in the screen.) Unclip the cover using a screwdriver in thecutout.)
Remove the cover.)
Extract the flat battery from its location.
)
Place the new battery into its location
observing the original direction. ) Clip the cover in place.

50
Access
Lost keys
Go to a PEUGEOT dealer with the vehicle's registration document, your personal identification documents and if possible the key code label. The PEUGEOT dealer will be able to look up the key code and the transponder code required to order a new key.
Remote control
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle. You run the risk of stopping it fromworking and the remote control would have to be reinitialised.No remote control can operate when the key is in the ignition switch, even when the ignition is switched off, except for reinitialisation.
Locking the vehicle
Driving with the doors locked may make access to the passenger compar tment by the emergency services more difficult in an emergency.
As a safety precaution, never leave children alone in the vehicle, except for a very shor t period. In all cases, it is essential to remove the key from the ignition switch when leaving the vehicle.
Anti-theft protection
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
When purchasing a second-hand vehicle
Have the pairing of all of the keys in your possession checked by a PEUGEOT dealer, to ensure that only your keys can be used to open andstart the vehicle.

51
2
Access
System which protects and provides a deterrent
against theft and break-ins. It provides the
following types of monitoring.





Alarm


- Exterior perimeter

The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet...




- Interior volumetric

The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or
moves inside the vehicle.
Self-protection function
The system checks for the putting out of service of its components. The alarm is triggered if the battery, thecentral control or the wires of the siren are put out of ser vice or damaged.
For all work on the alarm system, contact a PEUGEOT dealer or aqualified workshop.
Locking the vehicle with full
alarm system
Activation
)Switch off the ignition and get out of the vehicle.
) Press the locking button on the
remote control.
After the locking button on the remote control
is pressed, the exterior perimeter monitoring
is activated after a delay of 5 seconds and the
interior volumetric monitoring after a delay of 45 seconds.
If an opening (door, boot...) is not closed fully, the vehicle is not locked but the exterior
perimeter monitoring will be activated after a
dela
y of 45 seconds at the same time as the
interior volumetric monitoring.
)
Press the unlocking button on
the remote control.

Deactivation

The alarm system is deactivated: the
indicator lamp in the button goes off.
The monitoring system is active: the
indicator lamp in the button
flashes once per second.

52
Access
Locking the vehicle
w
ith exterior perimeter
monitoring only
Deactivate the interior volumetric monitoring
to avoid unwanted triggering of the alarm incertain cases such as:
- leaving a pet in the vehicle,
- leaving a window par tially open,
- washing your vehicle.
Deactivation of the interior volumetric monitoring
)
Switch off the ignition. )
Within ten seconds, press the button until the indicator lamp is
on continuously. ) Get out of the vehicle.
)
Press the locking button on the
remote control immediately.
The exterior perimeter monitorin
g alone is activated: the indicator lamp in the buttonflashes once per second.

Reactivation of the interior volumetric monitoring


Tr iggering of the alarm


This is indicated by sounding of the siren and flashing of the direction indicators for thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times in succession.
)Press the unlocking button on
the remote control to deactivate
the exterior perimeter monitoring.
) Press the locking button on theremote control to activate all themonitoring functions.
The indicator lamp in the button
a
gain flashes once per second.

When the vehicle is unlocked usin
gthe remote control, rapid flashing
of the indicator lamp in the button
in
forms you that the alarm was
triggered during your absence. When the ignition
is switched on, this flashing stops immediately.



Failure of the remote control

To deactivate the monitoring functions:
)Unlock the vehicle using the key in thedriver's door lock. )Open the door; the alarm is triggered.)Switch on the ignition; the alarm stops.
The indicator lamp in the button goes off.




Locking the vehicle without
activating the alarm
)Lock or deadlock the vehicle using the keyin the driver's door lock.


Malfunction


When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a mal
function of the system.
Have it checked by a PEUGEOT dealer or a qualified workshop.


*

According to country.


Automatic activation *



2 minutes after the last door or the boot isclosed, the system is activated automatically. )To avoid triggering the alarm on entering
the vehicle, first press the unlocking buttonon the remote control. To be effective, this deactivation mustbe carried out each time the ignition is switched off.

53
2
Access








Electric windows
1.Left hand front electric window.2.Right hand front electric window.3.Right hand rear electric window.4.Left hand rear electric window.5.Deactivating the rear electric window
switches.
Manual operation
To open or close the window, press or pull the
switch gently. The window stops as soon as theswitch is released.
Automatic one-touch
operation
(depending on version)
To open or close the window, press or pullthe switch fully: the window opens or closes completely when the switch is released.Pressing the switch again stops the movementof the window.
The electric window switches remain
operational for approximately one minute after
the key has been removed. Once this time has elapsed, the electric
windows will not operate. To reactivate them,
switch the ignition on again.

Safety anti-pinch
(depending on version)
When the window rises and meets an obstacle,it stops and immediately partially lowers again.
In the event of unwanted opening of the window
when closing automatically, press the switch
until the window opens completel
y, then pull
the switch immediately until the window closes.Continue to hold the switch for approximatelyone second after the window has closed.
The safety anti-pinch function is not activeduring this operation.


Deactivating the rear
window controls
For the safety of your children,press switch 5to prevent operation
of the windows of the rear doors,irrespective of their position.
With the warnin
g lamp on, the rear switches
are deactivated. With the warning lamp off,
the switches are active.

54
Access
Reinitialising the electric
w
indows
Following reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch is not active during these
operations:
- lower the window completel
y, then raise it, it will rise in steps of a few centimetres
each time the switch is pressed. Repeat
t
he operation until the window closescompletely,
- press and hold the switch upwards for at least one second after reaching this position, window closed.


Always remove the key when leavingthe vehicle, even for a shor t time. In the event of contact during operation of the windows, you must reverse themovement of the window. To do this, press the switch concerned.When operating the passenger electric window switches, the driver must ensure that no one is preventing correctclosing of the windows. The driver must ensure that thepassengers use the electric windows correctly.Be aware of children when operating thewindows.