2013 MERCEDES-BENZ SL-Class key

Display messages Possible causes/consequences and
0003 Solutions
0005(USA
only)
000B(Canada
only)
Parking Brake Inoperative The yellow
000Bwarning lamp lights up. The red 0005(USA
only)/ 000B(Canada only) indicato rlamp flashes for about ten
seconds after the electric parking brake has been applied or
released. It then goes out or remains lit.
The electric parking brake is malfunctioning, e.g .because of
overvoltage or undervoltage.
X Remove the cause for the overvoltage or undervoltage, e.g. by
charging the battery or restarting the engine.
X Engage or release the electric parking brake.
If it remains impossible to apply or release the electric parking
brake:
X Switch off the ignition and turn it back on.
X Engage or release the electric parking brake.
If the electric parking brake still cannot be released:
X Consult a qualified specialist workshop. The display message is only shown while the vehicle is in motion.
The yellow
000Bwarning lamp lights up and the red 0005(USA
only)/ 000B(Canada only) indicator lamp flashes.
It is not possible to apply the electric parking brake manually.
X Shift the transmission to P.
X Visit a qualified specialist workshop. 0005(USA
only)000B(Canada
only) The red
0005(USA only)/000B (Canada only) indicator lamp lights
up.
You attempted to release the electric parking brake while the
ignition was switched off.
X SmartKey: turn the SmartKey to position 1in the ignition lock.
X KEYLESS-GO: switch on the ignition. Display messages
245On-board computer and displays Z

Display messages Possible causes/consequences and
0003 Solutions
The roo
fhas been opened and closed several times in arow. The
roof drive has been switched off automatically for safety reasons.
You can open and close the roof again after approximately ten
minutes.
X Switch off the ignition and turn it back on.
X Repeat the opening or closing procedure (Y page 104).001A
Check Washer Fluid The washer fluid level in the washer fluid reservoir has dropped
below the minimum.
X
Add washer fluid (Y page 515).Wiper
Malfunctioning The windshield wipers are malfunctioning.
X
Visit a qualified specialist workshop. Hazard Warning
Flashers
Malfunctioning The hazard warning lamps are faulty.
X
Visit a qualified specialist workshop. SmartKey
Display messages Possible causes/consequences and
0003 Solutions
0002
Key Does Not
Belong to Vehicle You have put the wrong SmartKey in the ignition lock.
X
Use the correct SmartKey. 0002
Take
Your Key from
Ignition The SmartKey is in the ignition lock.
X
Remove the SmartKey. 0002
Obtain a New Key The SmartKey needs to be replaced.
X
Visit a qualified specialist workshop. 0002
Replace
Key Battery The batteries of the KEYLESS-GO key are discharged.
X
Change the batteries (Y page 87).0002
Don't Forget Your
Key The display message is shown for a maximum of 60 seconds and
is only a reminder.
You have opened the driver's door with the engine switched off.
The KEYLESS-GO key is not in the ignition lock.
X
Remember to take the KEYLESS-GO key with you when you
leave the vehicle. 268
Display messagesOn-board computer and displays

Display messages Possible causes/consequences and
0003 Solutions
0002
Key Not Detected
(red display message) The KEYLESS-GO key is not in the vehicle.
Aw
arning tone also sounds.
If the engine is switched off, you can no longer loc kthe vehicle
centrally or start the engine.
X Pull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
X Secure the vehicle against rolling away (Y page 175).
X Locate the KEYLESS-GO key. The KEYLESS-GO key is not detected while the engine is running
because there is interference from a strong source of radio waves.
Aw
arning tone also sounds.
X Pull ove rand stop the vehicle safely as soo nas possible, paying
attention to road and traffic conditions.
X Secure the vehicle against rolling away (Y page 175).
X Operate the vehicle with the SmartKey in the ignition lock. 0002
Key Not Detected
(white display
message) The KEYLESS-GO key cannot be detected at present.
X
Change the location of the SmartKey with the KEYLESS-GO
functions in the vehicle.
If the KEYLESS-GO key is still not detected:
X Operate the vehicle with the SmartKey in the ignition lock. 0002
Key Detected in
Vehicle The KEYLESS-GO key has been detected inside the vehicle during
locking.
X
Remove the KEYLESS-GO key from the vehicle. 0002
Remove Start
Button Then Insert
Key The KEYLESS-GO key can continuously not be detected.
KEYLESS-GO is temporarily malfunctioning or is defective. A
warning tone also sounds.
X
Insert the SmartKey into the ignition lock and turn it to the
desired position.
X Visit a qualified specialist workshop. 0002
Close Doors to
Lock Vehicle At least one door is open.
Awarning tone also sounds.
X Close all doors and loc kthe vehicle again. Display messages
269On-board computer and displays Z

X
Select the 0016symbol and press and hold
0039 the COMAND controller until the entire
entry has been deleted.
or
X Press and hold the 0016button next to the
COMAND controller until the entire entry
has been deleted. Character entry (navigation)
General information Character entry is explained in the following
sections using
NEW YORK as an example for
entering a city.
If you want to use the address entry menu to
enter a city, a stree torahouse number, for
example, COMAND offers you:
R a list with a character bar (option 1)
R a selection list (option 2)
You can enter the characters using either the
character bar or the number keypad. In the
selection list, you select an entry to copy it to
the address entry menu.
Option 1: city list/street list with
character bar X
Call up the city list with character bar
(Y page 319).
The alphabetically sorted city list shows the
first available entries. 0002
N character entered by user
0003 Characters automatically added by
COMAND ANTICOKE 0027
List entry that most closely resembles the
current entry by the user
0026 To switch to the selection list
0024 To delete an entry
0025 Characters not currently available
0016 Characters currently available
0017 Currently selected character
0018 Character bar
0019 To cancel an entry
001A List
Entering characters using the character
bar
X Select N by turning
003E0012003Fthe COMAND
controller and press 0039to confirm.
List 001Ashows all available city names
beginning with N .T
he list entry most closely
resembling user's current entry 0027is
always highlighted at the top of the list
(NANTICOKE in the example).
All characters currently entered by the user
are shown in black (letter N 0002
in the
example). Letters added by COMAND 0003
are shown in gray (letters ANTICOKE in the
example).
Character bar 0018shows letters still
available for selection 0016in black. These
can be selected; in the example, the letter
O is highlighted
0017. Which characters
remain available depends on the
characters already entered by the user and
on the data stored on the digital map.
Characters that are no longer available 0025
are shown in gray. At
ag lance
301COMAND Z

X
Select E ,
W , space,
Y in order and confirm
each with 0039.
Entering characters using the number
keypad
X To enter the letter N :p
ress the 0030
number button twice in quick succession.
The character appears at the bottom of the
display when the key is pressed. The first
available letter is highlighted.
You see which characters you can enter
with that key. Each time the key is pressed,
the next character is selected.
Example :key 0030:
R press once = M
R press twice =N
R press three times =O
X Wait until the character display goes out.
The entries matching your input are shown
in the list.
X Enter E ,
W , space,
Y with the corresponding
keys.
i The space is entered using number key
0004.
Further functions in the list with
character bar X
To delete characters: press the0029
button on the control panel.
or
X Press the 0016button next to the
COMAND controller.
or
X Select the 0016icon in the character bar
by sliding 0012000Aand turning 003E0012003Fthe
COMAND controller and press 0039to
confirm.
X To delete an entry: press0029on the
control panel.
or X
Press and hold the 0016button next to the
COMAND controller until the entire entry
has been deleted.
or
X Press and hold the 0016symbol in the
character bar and press and hold 0039the
COMAND controller until the entire entry
has been deleted.
X To cancel an entry: select the0027symbol
in the bottom left of the character bar and
press 0039to confirm.
or
X Press the 001Fback button.
The address entry menu appears.
X To accept the first list entry: press and
hold 0039the COMAND controller until the
address entry menu appears.
The accepted list entry is shown there.
Calling up the list as aselection list You can switch from th
elist of cities with the
character bar to the list of cities as a selection
list at any point during character entry.
X Slide 00380012the COMAND controller
repeatedly until the city list appears as a
selection list.
Selec tthe desired city from the selection
list.
or
X Select0004in the character bar by turning
003E0012003F the COMAND controller and press
0039 to confirm.
If there are several entries for a city or if
several cities of the same name are stored,
then 0004 is highlighted in the character bar.
X Press 0039the COMAND controller. 302
At
ag lanceCOMAND

COMAND calculates the rout
eto the
destination without taking account of the
following, for example:
R traffic lights
R stop and give way signs
R merging lanes
R parking or stopping in a no parking/no
stopping zone
R other road and traffic rules and regulations
R narrow bridges G
WARNING
COMAND may give incorrect navigation
commands if the actual road/traffic situation
no longer corresponds to the data on the
digital map. Digital maps do not cover all
areas nor all routes in an area. For example,
a route may have been diverted or the
direction of a one-way street may have
changed.
For this reason, you must always observe road
and traffic rules and regulations during your
journey. Road and traffic rules and regulations
always have priority over the system's driving
recommendations. G
WARNING
Navigation announcements are intended to
direct you while driving without diverting your
attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Looking at the icons or map display can
distract you from traffic conditions and
driving, and increase the risk of an accident.
General notes Operational readiness of the navigation
system
The navigation system must determine the
position of the vehicle before first use or
whenever operational status is restored.
Therefore, you may have to drive for a while
before precise route guidance is possible. GPS reception
Correct functioning of the navigation system
depends, amongst other things, on GPS
reception
.Incertain situations, GPS
reception may be impaired, there may be
interference or there may be no reception at
all, e.g. in tunnels or parking garages.
i Using roof carriers may impair the correct
functioning of a roof antenna (phone,
satellite radio, GPS).
Entry restriction
On vehicles for certain countries, there is a
restriction on entering data.
The restriction is active from a vehicle speed
of above approximately 3 mph (5 km/h). As
soon as the speed falls below approximately
2 mph (3 km/h), the restriction becomes
inactive.
When the restriction is active, certain entries
cannot be made. This will be indicated by the
fact that certain menu items are grayed out
and cannot be selected.
The following entries are not possible, for
example:
R entering the destination city and street
R entering a destination via the map
R entering POIs in the vicinity of a city or via
a name search
R editing entries
R using the number keypad for direct entry
Other entries are possible, such as entering
points of interest in the vicinity of the
destination or curren tposition. Navigation
315COMAND Z

X
Select Topographic Map and press
0039to
confirm.
Depending on the previous status, switch
the option on 0013or off 0003.
The topographical map uses different colors
to depict elevation. The color key generally
reflects the topography's dominant
vegetation or the ground's perceived color
when see nfrom the air, for example:
R green (grass) for lowland
R yellow, brow n(woodland) for hills
R gray (stone) and white (snow) for
mountains. Example: freeway information
Switching highway information on/off
When driving on the freeway, you can see the
following informatio nonthe right of the
display:
R the nearest gas stations
R the nearest rest areas, etc.
R and their distance from the current vehicle
position
The entries show the number of the
freeway and the freeway exits as well as
their distance from the current vehicle
position.
X To switch on navigation mode: press the
0014 function button.
X To show the menu: press0039the COMAND
controller. X
Select Navi in the main function bar by
sliding 00380012and turning 003E0012003Fthe COMAND
controller and press 0039to confirm.
X Select Map Settings and press
0039to
confirm.
The map settings menu appears.
X Select Freeway Information and press
0039 to confirm.
Depending on the previous status, switch
the option on 0013or off 0003. Example: city model
Switching city view on/off
When the city model is switched on, the map
shows buildings in 3D.
X
To show the menu: press0039the COMAND
controller.
X Select Navi in the main function bar by
sliding 00380012and turning 003E0012003Fthe COMAND
controller and press 0039to confirm.
X Select Map Settings and press
0039to
confirm.
The map settings menu appears.
X Select City (3D) and press
0039to confirm.
Depending on the previous status, switch
the option on 0013or off 0003.
i The city model is only shown for "Bird's-
eye View" or "3D Map".
It is available in the 0.05 mi and 0.1 mi map
scales.
The data required for displaying buildings
is not available for all cities. Navigation
367COMAND Z

Call disconnection while the vehicle is
in motion
Ac
all may be disconnected if:
R there is insufficient network coverage in
certain areas.
R you move from one transmitter/receiver
area (cell) into another and no channels are
free.
R you use a SIM card which is no tcompatible
with the network available.
Operating options You can operate the telephone by:
R
using the COMAND controller:
Turn 003E0012003F
Slide 003600120037 or00380012000A
Press 0039
R using the 0017or003C button and using
the telephone keypad on COMAND
R using the 0017or003C button on the
multifunction steering wheel
R using the Voice Control System (see the
separate Voice Control System operating
instructions)
Unless stated otherwise, the descriptions and
illustrations in this section refer to COMAND.
Function restrictions The telephone is not ready for use in the
following situations:
R the telephone automatically tries to log on
to a network .Ifno network is available, you
may not be able to make a " 911"
emergency call. If you attempt to make an
outgoing call, the No Service message will
appear for a short while.
911 emergency call G
WARNING
The 911 emergency call system is a public
service. Using it without due cause is a
criminal offense. The following requirements must be fulfilled
for a
911emergency call:
R the mobile phone must be switched on.
R a network must be available.
R a valid and operational SIM card must be
inserted in the mobile phone.
R the mobile phone is connected to COMAND
via Bluetooth ®
.
If you cannot make an emergency call, you
must arrange rescue measures yourself.
X Enter the number on COMAND
(Y page 384).
X Press 0017.
The telephone makes the connection.
X Wait until the emergency call center
answers and describe the emergency
situation. Telephony via the Bluetooth
®
interface
Conditions For telephony via COMAND's Bluetooth
®
interface, a Bluetooth ®
-capable mobile
phone is required.
On COMAND
X Activate the Bluetooth ®
function in
COMAND (Y page 306).
On the mobile phone
X Switch on the mobile phone and enter the
PIN when prompted to do so (see the
mobile phone operating instructions).
X Activate Bluetooth ®
functions and, where
necessary, Bluetooth ®
visibility on the
mobile phone (see the mobile phone
operating instructions).
The battery of the mobile phone should
always be kept sufficiently charged in order
to prevent malfunctions. Telephone
377COMAND Z