2013 MERCEDES-BENZ S-Class key

Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm withou
tawiper
blade and it falls onto th ewindshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Ben zrecommends that you have
the wiper blades replaced by aqualified
specialist workshop, e.g. at an authorized
Mercedes-Ben zCenter.
! Always position the windshield wiper
arms vertically before folding them away
from the windshield. By doing so, you will
avoid damage to the hood.
! To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
Changing the windshield wiper blades Moving the wiper blades to
avertical
position
Vehicles without KEYLESS-GO
X Turn the SmartKey to position 1or 2in the
ignitio nlock.
X Set the windshield wipers to
position 0014.
X When the wiper arms have reached a
vertical position, turn the SmartKey to
position 0and remove it from the ignition
lock.
Vehicles with KEYLESS-GO
X Switch off the engine.
X Remove your foot from the brake pedal.
X Set the windshield wipers to
position 0014.
X Press the Start/Stop button repeatedly
until the windshield wipers start.
X When the wiper arms have reached a
vertical position, press the Start/Stop
button. Removing the wiper blades
X
Fold the wiper arm away from the
windshield until it engages.
X Set the wiper blade at right angles to the
wiper arm. X
Remove the wiper blade from the retaining
pin on the wiper arm in the direction of the
arrow.
Installing the wiper blades
X Push the new wiper blade ontot he
retaining pin on the wiper arm in the
opposite direction to the arrow.
Make sure that the wiper blade slides fully
onto the retaining pin on the wiper arm.
X Turn the wiper blade parallel to the wiper
arm.
X Fold the wiper arm back onto the
windshield. Problems with the windshield wipers
The windshield wipers are obstructed Leaves or snow, for example, may be
obstructing the windshield wiper movement.
The wiper motor has been deactivated.
X
For safety reasons, you should remove the
SmartKey from the ignition lock.
or
X Switch off the engine using the Start/Stop
button and open the driver's door.
X Remove the cause of the obstruction.
X Switch the windshield wipers back on. 290
Windshield wipersLights and windshield wipers

Useful information
i This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
i Please read the information on qualified
specialist workshops (Y page 31).Overview of climate control systems
Important safety notes
G
WARNING
Severe conditions (e.g. strong air pollution)
may require replacement of the filter before
its scheduled replacement interval. Aclogged
filter will reduce the air volume to the interior
and the windows could fog up, impairing
visibility and endangering you and others.
Have a blocked filter replaced at a Mercedes-
Ben zCenter as soon as possible. G
WARNING
Follow the recommended settings for heating
and cooling given on the following pages.
Otherwise, the windows could fog up,
impairing visibility and endangering you and
others.
Automatic climate control controls the
temperature and the humidity in the vehicle
interior and filters undesirable substances
from the air.
Automatic climate control is only operational
when the engine is running 16
.O ptimum
operation is only achieved if you drive with the
side windows and sliding sunroof/panorama
roof with power tilt/sliding panel closed. You can also set some automatic climate
contro
lfunction svia COMAND (Y page 269).
i Ventilate the vehicle for a brief period
during warm weather, e.g. using the
convenience opening feature (Y page 96).
This will speed up the cooling process and
the desired vehicle interior temperature
will be reached more quickly.
i The integrated filter can filter out most
particles of dust, and completely filters out
pollen .Aclogged filter reduces the amount
of air supplied to the vehicle interior .For
this reason, you should always observe the
interval for replacing the filter, which is
specified in the Maintenance Booklet .As it
depends on environmental conditions, e.g.
heavy air pollution, the interval may be
shorter than stated in the Maintenance
Booklet.
i It is possible that the blower may be
activated automatically 40 minutes after
the SmartKey is removed. The vehicle is
then ventilated for 30 minutes to dry the
air-conditioning system.
16 The residual heat function can only be activated/deactivated if the ignition is switched off. 294
Overview of climate control systemsClimate control

Notes on using climate control
Below, you can find a numbe rofnotes and
recommendations to help you use climate
control optimally.
R Activate climate control using the 0004
rocker switch. The indicator lamp in the
0004 rocker switch lights up.
R Set the temperature to 72 ‡ (22 † ).
R Only use the "defrosting" function briefly
until the windshield is clear again.
R Only use "air-recirculation" mode briefly,
e.g. if there are unpleasant outside odors
or when in a tunnel. The windows could
otherwise fog up as in air-recirculation
mode no fresh air is drawn into the vehicle.
R Use the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
"residual heat" function can only be
activated or deactivated with the ignition
switched off. Operating the climate control
systems
Activating/deactivating climate
control
Important information G
WARNING
When the climate control system is
deactivated, the outside air supply and
circulation are also deactivated. Only choose
this setting for a short time. Otherwise the
windows could fog up, impairing visibility and
endangering you and others.
i Switch on climate control primarily using
the 0004 rocker switch (Y page 297). Switching the front climate control on/
off using the front control panel X
Turn the SmartKey to position 2in the
ignition lock.
X To activate: press the0012rocker switch
up or down.
The indicator lamp in the rocker switch
goes out. The previously selected settings
come into effect again.
X To deactivate: press the0012rocker
switch up or down.
The indicator lamp in the rocker switch
lights up.
Switching the rear-compartment
climate control on/off using the front
control panel X
Turn the SmartKey to position 2in the
ignition lock.
X Activate the 0007rear compartment
function via COMAND (Y page 273).
The rear-compartment climate control can
be controlled via the front control panel
using the 0007rear compartment function.
X To activate: press the0012rocker switch
up or down.
The indicator lamp in the rocker switch
goes out. The previously selected settings
come into effect again.
X To deactivate: press the0012rocker
switch up or down.
The indicator lamp in the rocker switch
lights up. 296
Operating the climate control systemsClimate control

Switching the rear-compartment
climate control on/off using the rear
control panel X
Turn the SmartKey to position 2in the
ignition lock.
X To switch on: press rocker switch
001F(Y page 295) up or down and select
AUTO .
or
X Press rocker switch 001F(Ypage 295) up or
down and select MAN .
X To switch off: press rocker switch
001F(Y page 295) up or down and select
OFF .
Activating/deactivating cooling with
air dehumidification
Important information The cooling with air dehumidification function
is only available when the engine is running.
The air inside the vehicle is cooled and
dehumidified according to the temperature
selected. G
WARNING
If you switch off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog up
more quickly. Window fogging may impair
visibility and endanger you and others.
Condensation may drip from the underside of
the vehicle when it is in cooling mode. This is
normal and not a sign that there is a
malfunction.
You can activate or deactivate the cooling
with air dehumidification function via
COMAND (Y page 271).
i The cooling with air dehumidification
function uses refrigerant R134a. This
coolant does not contain
chlorofluorocarbons, and therefore does
not damage the ozone layer. Problems with the cooling with air
dehumidification function If you can no longer switch on the cooling with
air dehumidification function via COMAND,
the cooling with air dehumidification function
is switched off due to a malfunction.
X
Consult a qualified specialist workshop. Setting climate control to automatic
G
WARNING
If you switch off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog up
more quickly. Window fogging may impair
visibility and endanger you and others.
In automatic mode, the set temperature is
maintained automatically at a constant level.
The system automatically regulates the
temperature of the dispensed air, the airflow
and the air distribution.
Automatic mode will achieve optimal
operation if cooling with air dehumidification
is also activated. If desired, cooling with air
dehumidification can be deactivated.
Controlling the front climate control
using the front control panel X
Turn the SmartKey to position 2in the
ignition lock.
X Set the desired temperature.
X To switch on: press the0004rocker
switch up or down.
The indicator lamp in the 0004rocker
switch lights up. Operating the climate control systems
297Climate control Z

X
To deactivate: press the0016rocker
switch up or down.
The indicator lamp in the 0004rocker
switch goes out.
or
X Set the ai rdistribution using COMAND
(Y page 270).
The indicator lamp in the 0004rocker
switch goes out.
Controlling the rear-compartment
climate control automatically using the
front control panel X
Turn the SmartKey to position 2in the
ignition lock.
X Activate the 0007rear compartment
function via COMAND (Y page 273).
Rear-compartment climate control can be
controlled via the front control panel using
the 0007 rear compartment function.
X Set the desired temperature.
X To switch on: press rocker switch 0004
up or down.
The indicator lamp in the 0004rocker
switch lights up.
X To deactivate: press the0016rocker
switch up or down.
The indicator lamp in the 0004rocker
switch goes out.
or
X Set the air distribution using COMAND
(Y page 270).
The indicator lamp in the 0004rocker
switch goes out.
i To return to the standard display, activate
the front climate control function via
COMAND (Y page 273).
i The rear display changes to the standard
display automatically after five seconds. Controlling the rear-compartment
climate control automatically using the
rear control panel X
Turn the SmartKey to position 2in the
ignition lock.
X Set the desired temperature.
X To activate: press rocker switch 001Fup or
down and select AUTO (Y
page 295).
X To deactivate: press rocker switch 001Fup
or down and select MAN or
OFF (Y
page 295). Setting the temperature
Climate control climate zones
You can selec
tdifferen ttemperature settings
for the driver's and front-passenger sides as
well as for the left and right sides of the rear
compartment and the footwells.
Setting the temperature in the front
compartment using the front control
panel X
Turn the SmartKey to position 2in the
ignition lock.
X To increase/reduce: press the0012
rocker switch up or down.
Only change the temperature setting in
small increments. Start at 72 ‡ (22 † ).
i You can also use COMAND to set the
temperature (Y page 270).298
Operating the climate control systemsClimate control

Setting the temperature in the rear
compartment using the front control
panel X
Turn the SmartKey to position 2in the
ignition lock.
X Activate the "rear 0007" function via
COMAND (Y page 273).
Using the "rear 0007" function, the rear-
compartment climate control can be
controlled via the front control panel.
X To increase/reduce: press the0012
rocker switch up or down.
Only change the temperature setting in
small increments. Start at 72 ‡ (22 † ).
i To return to the standard display, activate
the front climate control function via
COMAND (Y page 273).
i The rear display changes to the standard
display automatically after five seconds.
Setting the temperature in the rear
compartment using the rear control
panel X
Turn the SmartKey to position 2in the
ignition lock.
X To increase/reduce: press rocker
switch 001Cor0022 up or down (Y page 295).
Only change the temperature setting in
small increments. Start at 72 ‡ (22 † ).
Setting the footwell temperature The footwell temperature can be set via
COMAND (Y page 272). Setting the air distribution
Air distribution settings The air distribution can be set individually for
the driver's and front-passenger sides.
0005 Directs air through the defroster vents
0018 Directs air through the center and side
air vents 0017
Directs the airflow through the
footwell air vents
0019 Directs air through the center, side and
footwell vents
0013 Directs air through the defroster and
footwell vents
0015 Directs air through the defroster,
center, side and footwell vents
0014 Directs air through the defroster,
center and side air vents
0006 Sets the air distribution to automatic
Setting the air distribution in the front/
rear compartment using COMAND The air distribution can be set using COMAND
(Y
page 270).
Setting the air distribution in the rear
compartment using the rear control
panel X
Turn the SmartKey to position 2in the
ignition lock.
X Press rocker switch 001Dor0021 up or down
repeatedly (Y page 295) until the desired
air distribution symbol is shown in the
display. Setting the airflow
Setting the front-compartment airflow
using the front control panel You can select different airflow settings for
the driver's and front-passenger sides as well
as for the rear compartment.
You can also use COMAND to set the airflow
(Y
page 271).
X Turn the SmartKey to position 2in the
ignition lock.
X To increase/reduce: press the0016
rocker switch up or down. Operating the climate control systems
299Climate control Z

Setting the rear-compartment airflow
using the front control panel X
Turn the SmartKey to position 2in the
ignition lock.
X Activate the 0007rear compartment
function via COMAND (Y page 273).
The rear-compartment climate control can
be controlled via the front control panel
using the 0007rear compartment function.
X To increase/reduce: press the0016
rocker switch up or down.
Setting the rear-compartment airflow
using the rear control panel X
Turn the SmartKey to position 2in the
ignition lock.
X To increase/reduce: press rocker switch
001E up or down (Y page 295). Defrosting the windshield
You can use this function to defrost the
windshield or to defrost the inside of the
windshield and the side windows.
i You should only select the defrosting
function until the windshield is clear again.
X Turn the SmartKey to position 2in the
ignition lock.
X To switch on: press the0008rocker
switch up or down.
The indicator lamp in the 0008rocker
switch lights up.
The climate control system switches to the
following functions:
R cooling with air dehumidification on
R high airflow 17
R high temperature 17
R air distribution to the windshield and
front side windows
R air-recirculation mode off X
To deactivate: press the0008rocker
switch up or down.
The indicator lamp in the 0008rocker
switch goes out. The previously selected
settings come into effect again. The cooling
with air dehumidification function remains
on. Air-recirculation mode remains
deactivated.
or
X Press the 0012rocker switch up or down.
or
X Press the 0016rocker switch up or down. MAX COOL maximum cooling
The MAX COOL function is only available in
vehicles for the USA.
MAX COOL is only operational when the
engine is running.
The MAX COOL function is activated
automatically:
R if climate control is set to automatic
(0004) on both sides
R if additional cooling is used
The display shows MAX COOL .
This is the quickest way to cool the vehicle
interior when the sliding sunroof and the side
windows are closed. Defrosting the windows
Windows fogged up on the inside X
Activate the cooling with air
dehumidification function via COMAND
(Y page 271).
X Activate automatic mode 0004.
X If the windows continue to fog up, activate
the defrosting function (Y page 300).
i You should only select this setting until
the windshield is clear again.
17 Depending on the outside temperature. 300
Operating the climate control systemsClimate control

Windows fogged up on the outside
X
Switch on the windshield wipers.
X Activate automatic climate control.
i You should only select this setting until
the windshield is clea ragain. Rear window defroster
Activating/deactivating G
WARNING
Any accumulation of snow and ice should be
removed from the rear window before driving.
Visibility could otherwise be impaired,
endangering you and others.
The rear window defroster has a high current
draw. You should therefore switch it off as
soon as the window is clear. Otherwise, the
rear window defroster switches off
automatically after several minutes.
If the battery voltage is too low, the rear
window defroster may switch off.
X Turn the SmartKey to position 2in the
ignition lock.
X Press the 000Brocker switch up or down.
The indicator lamp in the 000Brocker
switch lights up or goes out.
Problems with the rear window
defroster The rear window defroster has deactivated
prematurely or cannot be activated.
X
Switch off any consumers that are not
required, e.g. reading lamps or interior
lighting.
When the battery is sufficiently charged,
the rear window defroster is activated
again automatically. Activating/deactivating air-
recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle
from outside. The air already inside the
vehicle will then be recirculated. G
WARNING
Fogged windows impair visibility,
endangering you and others. If the windows
begin to fog on the inside, switching off the
air recirculation mode immediately should
clear interior window fogging. If interior
window fogging persists, make sure the air
conditioning is activated, or press the 0008
button.
X Turn the SmartKey to position 2in the
ignition lock.
X To activate: press the0010rocker switch
up or down.
The indicator lamp in the 0010rocker
switch lights up.
i Air-recirculation mode is activated
automatically at high outside
temperatures. The indicator lamp in the
0010 rocker switch is not lit when
automatic air-recirculation mode is
activated.
Outside air is added after about
30 minutes.
X To deactivate: press the0010rocker
switch up or down.
The indicator lamp in the 0010rocker
switch goes out. Operating the climate control systems
301Climate control Z