2013 Lexus CT200h tom tom

1763-4. Adjusting the steering wheels and mirrors
CT200h_OM_OM76102E_(EE)
Mirror angle can be adjusted when
The power switch is in ACCESSORY or ON mode.
Linked mirror function when reversing (type B only)
When the mirror select switch is in the “L” or “R” position, the outside rear view
mirrors will automatically angle downwards when the vehicle is reversing in
order to give a better view of the ground. To disable this function, move the mir-
ror select switch to the neutral position (between “L” and “R”).
Rain clearing mirrors (type B only)
The coating on the mirror has the rain clearing (hydrophilic) effect to make the
rear view clearer in raining. When water droplets collects on the mirror surface,
this effect causes the droplets to be spread out into a film.
The rain clearing effect will be reduced temporarily, when the dirt is adhered to
the mirror or after your vehicle is parked for a long time in underground or
indoor parking lots, etc., where there is no direct sunlight. However, the effect
will gradually recover after 1- or 2-day exposure to direct sunlight.
If you want to restore the rain clearing effect immediately, conduct the resto-
ration work (P. 481).
When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on
the rear window defogger to turn on the outside rear view mirror defoggers.
(P. 447, 454)
Automatic adjustment of the mirror angle (vehicles with driving position mem-
ory)
A desired mirror face angle can be entered to memory and recalled automatically
by the driving position memory. (P. 163)
Auto anti-glare function (type B only)
When the anti-glare inside rear view mirror is set to automatic mode, the outside
rear view mirrors will activate in conjunction with the anti-glare inside rear view
mirror to reduce reflected light. (P. 172)
Using automatic mode in cold weather (type B only)
When automatic mode is used in cold weather, the door mirror could freeze up
and automatic stowing and return may not be possible. In this event, remove any
ice and snow from the door mirror, then either operate the mirror using manual
mode or move the mirror by hand.
Customization
The automatic mirror folding and extending operation can be changed.
(Customizable features: P. 659)

1793-5. Opening, closing the windows and moon roof
3
Operation of each component
CT200h_OM_OM76102E_(EE)
The power windows can be operated when
The power switch is in ON mode.
Operating the power windows after turning the hybrid system off
The power windows can be operated for approximately 45 seconds even after the
power switch is turned to ACCESSORY mode or turned off. They cannot, how-
ever, be operated once either front door is opened.
Jam protection function
If an object becomes caught between the window and the window frame, win-
dow travel is stopped and the window is opened slightly.
When the power window does not close normally
If the jam protection function is operating abnormally and a window cannot be
closed, perform the following operations using the power window switch on the
relevant door.
After stopping the vehicle, the window can be closed by holding the power
window switch in the one-touch closing position while the power switch is
turned to ON mode.
If the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following procedure.
Hold the power window switch in the one-touch closing position. Continue
holding the switch for a further 6 seconds after the window has closed.
Hold the power window switch in the one-touch opening position. Continue
holding the switch for a further 2 seconds after the window has opened com-
pletely.
Hold the power window switch in the one-touch closing position once again.
Continue holding the switch for a further 2 seconds after the window has
closed.
If you release the switch while the window is moving, start again from the begin-
ning.
If the window continues to close but then re-open slightly even after performing
the above procedure correctly, have the vehicle inspected by any authorized
Lexus dealer or repairer, or another duly qualified and equipped professional.
Door lock linked window operation
The power windows can be opened and closed using the mechanical key.*
(P. 621)
The power windows can be opened and closed using the wireless remote con-
trol.* (P. 132)
*: These settings must be customized at any authorized Lexus dealer or repairer,
or another duly qualified and equipped professional.
Customization
Setting (e.g. linked door lock operation) can be changed.
(Customizable features:
P. 650)
1
2
3

181
3 3-5. Opening, closing the windows and moon roof
Operation of each component
CT200h_OM_OM76102E_(EE)
Moon roof
Opens the moon roof*
Push and hold “OPEN” for more
than 1 second. The moon roof tilts
up and then opens automatically.
Closes the moon roof*
Push and hold “CLOSE” for more
than 1 second. The moon roof closes
automatically to the tilt up position.
Push and hold “CLOSE” again to
fully close the moon roof.
*: Lightly press either end of the moon
roof switch to stop the moon roof
partway.
Tilts the moon roof up*
Tilts the moon roof down*
*
: Lightly press either end of the moon
roof switch to stop the moon roof
partway.
: If equipped
Use the overhead switches to open and close the moon roof and tilt it up
and down.
Opening and closing
1
2
Tilting up and down
1
2

1823-5. Opening, closing the windows and moon roof
CT200h_OM_OM76102E_(EE)
The moon roof can be operated when
The power switch is in ON mode.
Operating the moon roof after turning the hybrid system off
The moon roof can be operated for approximately 45 seconds even after the
power switch is turned to ACCESSORY mode or turned off. It cannot, however,
be operated once either front door is opened.
Jam protection function
If an object is detected between the moon roof and the frame while the moon roof
is closing or tilting down, travel is stopped and the moon roof opens slightly.
Sunshade
The sunshade can be opened and closed manually. However, the sunshade will
open automatically to slightly before the fully open position when the moon roof
is opened.
When the moon roof does not close normally
Perform the following procedure:
If the moon roof closes but then re-opens slightly
Stop the vehicle.
Press and hold the “CLOSE” switch.
*1
The moon roof will close, reopen and pause for approximately 10 sec-
onds.
*2 Then it will close again and tilt down. Finally it will be adjusted
slightly and then stop.
Check to make sure that the moon roof completely stops and then release the
switch.
If the moon roof tilts down but then tilts back up
Stop the vehicle.
Press and hold the “DOWN” switch.
*1
The moon roof will close, reopen and pause for approximately 10 seconds in
the tilt up position.
*2 Then it will close again and tilt down. Finally it will be
adjusted slightly and then stop.
Check to make sure that the moon roof has completely stopped and then
release the switch.
*1: If the switch is released at the incorrect time, the procedure will have to be
performed again from the beginning.
*2: If the switch is released after the above mentioned 10 second pause, auto-
matic operation will be disabled. In that case, press and hold the “CLOSE”
or “DOWN” switch, and the moon roof will close, be adjusted slightly and
then stop. Check to make sure that the moon roof has completely stopped
and then release the switch.
If the moon roof does not fully close even after performing the above procedure
correctly, have the vehicle inspected by any authorized Lexus dealer or repairer,
or another duly qualified and equipped professional.
1
2
3
1
2
3

1964-2. Driving procedures
CT200h_OM_OM76102E_(EE)
Power (ignition) switch
Check that the parking brake is set.
Firmly depress the brake pedal.
Check that the power switch indicator turns green. If the indicator does not
turn green, the hybrid system cannot be started.
When the shift position is N, the hybrid system cannot start. Shift the shift
position to P when starting the hybrid system. (P. 205)
Press the power switch.
Continue depressing the brake pedal
until the hybrid system is completely
started.
The hybrid system can be started
from any power switch mode.
Check that the “READY” indicator is illuminated.
If the “READY” indicator changes from a flashing light to a solid light and
the buzzer sounds, the hybrid system is starting normally.
The vehicle will not move when the “READY” indicator is off.
The vehicle can move when the “READY” indicator is on even if the engine
is stopped. (The gasoline engine starts or stops automatically in accordance
with the state of the vehicle.)
Performing the following operations when carrying the electronic key on
your person starts the hybrid system or changes power switch modes.
Starting the hybrid system
1
2
3
4

1984-2. Driving procedures
CT200h_OM_OM76102E_(EE)
Modes can be changed by pressing the power switch with the brake pedal
released. (The mode changes each time the switch is pressed.)
Off
The emergency flashers can be used.
ACCESSORY mode
Some electrical components such as
the audio system can be used.
The power switch indicator turns
amber.
ON mode
All electrical components can be
used.
The power switch indicator turns
amber.
Auto power off function
If the vehicle is left in ACCESSORY mode for more than 20 minutes or ON
mode (the hybrid system is not operating) for more than an hour with the shift
position in P, the power switch will automatically turn off. However, this func-
tion cannot entirely prevent the 12-volt battery discharge. Do not leave the vehi-
cle with the power switch in ACCESSORY or ON mode for long periods of time
when the hybrid system is not operating.
Sounds and vibrations specific to a hybrid vehicle
P. 8 0
Electronic key battery depletion
P. 129
Changing power switch modes
1
2
3

1994-2. Driving procedures
4
Driving
CT200h_OM_OM76102E_(EE)
When the ambient temperature is low, such as during winter driving conditions
When starting the hybrid system, the flashing time of the “READY” indicator
may be long. Leave the vehicle as it is until the “READY” indicator is steady on,
as steady means the vehicle is able to move.
Conditions affecting operation
P. 145
Note for the entry function
P. 146
If the hybrid system does not start
The immobilizer system may not have been deactivated. (P. 87)
Contact any authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
When the power switch indicator flashes in amber
The system may be malfunctioning. Have the vehicle inspected by any autho-
rized Lexus dealer or repairer, or another duly qualified and equipped profes-
sional immediately.
If the “READY” indicator does not come on
In the event that the “READY” indicator does not come on even after performing
the proper procedures for starting the vehicle, contact any authorized Lexus
dealer or repairer, or another duly qualified and equipped professional immedi-
ately.
If the hybrid system is malfunctioning
P. 580
If the electronic key battery is depleted
P. 530
Operation of the power switch
When operating the power switch, one short, firm press is enough. If the switch
is pressed improperly, the hybrid system may not start or the power switch
mode may not change. It is not necessary to press and hold the switch.
If attempting to restart the hybrid system immediately after turning the power
switch off, the hybrid system may not start in some cases. After turning the
power switch off, please wait a few seconds before restarting the hybrid system.
Automatically P position selection function
P. 207
When the P position control system malfunctions
The power switch will not be able to be turned off. In such a case, the switch can
be turned off after applying the parking brake.
Have the vehicle inspected by any authorized Lexus dealer or repairer, or another
duly qualified and equipped professional immediately.

2004-2. Driving procedures
CT200h_OM_OM76102E_(EE)
WA R N I N G
When starting the hybrid system
Always start the hybrid system while sitting in the driver’s seat. Do not depress
the accelerator pedal while starting the hybrid system under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
Stopping the hybrid system in an emergency
If you want to stop the hybrid system in an emergency while driving the vehi-
cle, press and hold the power switch for more than 2 seconds, or press it briefly
3 times or more in succession. (P. 561)
However, do not touch the power switch while driving except in an emergency.
Turning the hybrid system off while driving will not cause loss of steering or
braking control, however, power assist to the steering will be lost. This will
make it more difficult to steer smoothly, so you should pull over and stop the
vehicle as soon as it is safe to do so.
NOTICE
To prevent 12-volt battery discharge
Do not leave the power switch in ACCESSORY or ON mode for long periods
of time without the hybrid system on.
If the hybrid system is off, but the indicator on the power switch is illumi-
nated, this indicates that the power switch is still turned on. When exiting the
vehicle, always check that the power switch is off.
When starting the hybrid system
If the hybrid system becomes difficult to start, have your vehicle checked by
any authorized Lexus dealer or repairer, or another duly qualified and equipped
professional immediately.
Symptoms indicating a malfunction with the power switch
If the power switch seems to be operating somewhat differently than usual,
such as the switch sticking slightly, there may be a malfunction. Contact any
authorized Lexus dealer or repairer, or another duly qualified and equipped
professional immediately.