2013 Lexus CT200h change time

4556-1. Using the air conditioning system and defogger
CT200h_OM_OM76102E_(EE)
6
Interior features
Windshield wiper de-icer (if equipped)
This feature is used to prevent ice from building up on the windshield
and wiper blades.
Turns on/off.
The indicator comes on when the
windshield wiper de-icer is on.
The windshield wiper de-icer will
automatically turn off after a
period of time.
Location of air outlets
The air outlets and air volume
changes according to the selected
air flow mode.
Adjusting the position of and opening and closing the air outlets
Direct air flow to the left or
right, up or down.
Turn the knob to open or close
the vent.
Air outlets
1
2

4576-1. Using the air conditioning system and defogger
CT200h_OM_OM76102E_(EE)
6
Interior features
When the outside temperature is low
The dehumidification function may not operate even when “A/C” is pressed.
Operation of the air conditioning system in Eco drive mode
In the Eco drive mode, the air conditioning system is controlled as follows to
prioritize fuel efficiency
• Engine speed and compressor operation controlled to restrict heating/cooling
capacity
• Fan speed restricted when automatic mode is selected
To improve air conditioning performance, perform the following operations
• Adjust the fan speed
• Turn off Eco drive mode
• Customize the air conditioning control of Eco drive mode. (P. 658)
Ventilation and air conditioning odors
To let fresh air in, set the air conditioning system to the outside air mode.
During use, various odors from inside and outside the vehicle may enter into
and accumulate in the air conditioning system. This may then cause odor to be
emitted from the vents.
To reduce potential odors from occurring:
• It is recommended that the air conditioning system be set to outside air mode
prior to turning the vehicle off.
• The start timing of the blower may be delayed for a short period of time
immediately after the air conditioning system is started in automatic mode.
Air conditioning filter
P. 527
Customization
Settings (e.g. A/C automatic mode switch operation) can be changed.
(Customizable features: P. 650)

4636-2. Using the interior lights
CT200h_OM_OM76102E_(EE)
6
Interior features
Illuminated entry system: The lights automatically turn on/off according to
power switch mode, the presence of the electronic key, whether the doors are
locked/unlocked, and whether the doors are opened/closed.
If the interior lights remain on when the power switch is turned off, the lights
will go off automatically after 20 minutes.
Settings (e.g. the time elapsed before the lights turn off) can be changed.
(Customizable features: P. 655)
NOTICE
To prevent 12-volt battery discharge, do not leave the lights on longer than nec-
essary when the hybrid system is off.

5157-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
The initialization operation
Make sure to carry out initialization after adjusting the tire inflation pressure.
Also, make sure the tires are cold before carrying out initialization or tire infla-
tion pressure adjustment.
If you have accidentally turned the power switch off during initialization, it is
not necessary to press the reset switch again as initialization will restart auto-
matically when the power switch has been turned to ON mode for the next time.
If you accidentally press the reset switch when initialization is not necessary,
adjust the tire inflation pressure to the specified level when the tires are cold,
and conduct initialization again.
Warning performance of the tire pressure warning system
The warning of the tire pressure warning system will change in accordance with
the conditions under which it was initialized. For this reason, the system may
give a warning even if the tire pressure does not reach a low enough level, or if
the pressure is higher than the pressure that was adjusted to when the system was
initialized.
When initialization of the tire pressure warning system has failed
Initialization can be completed in a few minutes. However, in the following
cases, the settings have not been recorded and the system will not operate prop-
erly. If repeated attempts to record tire inflation pressure settings are unsuccess-
ful, have the vehicle inspected by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
When operating the tire pressure warning reset switch, the tire pressure warning
light does not blink 3 times.
After carrying out the initialization procedure, the tire pressure warning light
blinks for 1 minute then stays on after driving for 20 minutes.

6238-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
8
When trouble arises
Depress the brake pedal.
Touch the Lexus emblem side of
the electronic key to the power
switch.
If any of the doors is opened or
closed while the key is being
touched to the switch, an alarm will
sound to indicate that the start func-
tion cannot detect the electronic key.
Press the power switch within 10 seconds of the buzzer sounding,
keeping the brake pedal depressed.
In the event that the hybrid system still cannot be operated, contact any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
Stopping the hybrid system
Set the parking brake, shift the shift position to P and press the power switch as
you normally do when stopping the hybrid system.
Replacing the key battery
As the above procedure is a temporary measure, it is recommended that the elec-
tronic key battery be replaced immediately when the battery is depleted. (P.
530)
Alarm (if equipped)
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set, the
alarm may be triggered. (P. 9 3 )
Changing power switch modes
Within 10 seconds of the buzzer sounding, release the brake pedal and press the
power switch.
The hybrid system does not start and modes will be changed each time the switch
is pressed. (P. 198)
Starting the hybrid system
1
2
3

6579-2. Customization
CT200h_OM_OM76102E_(EE)
9
Vehicle specifications
*1: Settings that can be changed on vehicles with the tachometer
*2: The default setting varies according to countries.
*3: If equipped
*4: Some status screens cannot be registered (indicated on the multi-information
display)
*5: 2 of the following items: current fuel consumption, average fuel economy
(after reset), average fuel economy (after refuel), average fuel economy (after
start), average vehicle speed (after reset), average vehicle speed (after start),
distance (driving range), distance (after start), elapsed time (after reset),
elapsed time (after start), blank
Drive information 1*3
Current fuel
consumption
*5–OOOAverage fuel
consumption
(after reset)
Drive information 2*3
Cruising range/
Distance
*5–OOOAverage speed
(after reset)
Pop-up display*3OnOff–OOO
Accent color*3BlueBrownOOOO
Sensitivity of the ambient
light sensor used for dim-
ming the meter light etc.
*3Standard-2 to 2–––O
Sensitivity of the ambient
light sensor used for bright-
ening the meter light etc.
*3Standard-2 to 2–––O
FunctionDefault
settingCustomized
setting1234