2013 Lancia Voyager tailgate

Left and right third row seats can be
folded individually or together. The
third row power folding seat adjusts
to the following positions using the
switch bank located on the left rear
trim panel:
NOTE:
 Disconnect the center shoulderbelt from the small buckle and
lower the head restraints before
attempting to fold/stow the
power third row seats.  To abort seat operation while
seat is in motion, press a differ-
ent seat position selector switch
to stop the seat. Once the seat
stops moving, then the desired
position can be selected.
 The third row power seat system includes obstacle detection for
safe operation. When the system
detects an obstacle, the motors
will stop and reverse the motion
a short distance to move the seat
away from the obstacle. Should
this occur, remove the obstacle
and press the button again, for
the desired position.
MANUALLY FOLDING
THIRD ROW SEATS (for
versions/markets, where
provided)
1. Lower the center head restraint
down to the seatback by pushing the
button on the guide and pushing the
head restraint down. 2. Lower the outboard head re-
straints by pulling on the release strap
marked “1” located on the outboard
side of the head restraint.
3. Pull release strap marked “2” lo-
cated on the rear of the seat to lower
the seatback.
4. Pull release strap marked “3” to
release the anchors.
Rear Panel Power Switch Bank
1 — Open to
Normal
2 — Stow
3 — Tailgate/
Fold Flat 4 — Right/Left
Seats/Both Seats
Head Restraint Release Strap “1”
Release Strap “2”
118

5. Pull release strap marked “4” and
tumble the seat rearward into the
storage bin.To Unfold Third Row Seats
1. Pull up on the assist strap to lift
the seat out of the storage bin and
push the seat forward until the an-
chors latch.
2. Pull release strap marked “2” to
unlock the recliner.
3. Pulling strap “4” releases the seat-
back to return to its full upright posi-
tion.
4. Raise the head restraint to its up-
right position.
WARNING!
In a collision, you or others in your
vehicle could be injured if seats are
not properly latched to their floor
attachments. Always be sure the
seats are fully latched.
Tailgate Mode
1. Pull release strap “3”, then pull
release strap “4” to rotate the entire
seat rearward.
2. To restore the seat to its upright
position, lift up on the seatback and
push forward until the anchors latch.WARNING!
To avoid serious injury or death,
never operate the vehicle with oc-
cupants in the third row seat while
in the tailgate mode.
PLASTIC GROCERY BAG
RETAINER HOOKS
Retainer hooks which will hold plastic
grocery bag handles are built into the
seatbacks of all rear seats and some
front seats. The floor supports the
partial weight of the bagged goods.
Release Strap “3”Release Strap “4”
Stowed Third Row Seat
119

 On vehicles equipped with atailgate, ParkSense® should be
disabled when the tailgate is in
the lowered or open position
and the vehicle is in REVERSE.
A lowered tailgate could provide
a false indication that an ob-
stacle is behind the vehicle.CAUTION!
 ParkSense® is only a parking aidand it is unable to recognize every
obstacle, including small ob-
stacles. Parking curbs might be
temporarily detected or not de-
tected at all. Obstacles located
above or below the sensors will
not be detected when they are in
close proximity.
 The vehicle must be driven slowly when using ParkSense® in order
to be able to stop in time when an
obstacle is detected. It is recom-
mended that the driver looks over
his/her shoulder when using
ParkSense®.
WARNING!
 Drivers must be careful whenbacking up even when using the
Rear Park Assist system. Always
check carefully behind your ve-
hicle, look behind you, and be
sure to check for pedestrians, ani-
mals, other vehicles, obstruc-
tions, and blind spots before
backing up. You are responsible
for safety and must continue to
pay attention to your surround-
ings. Failure to do so can result in
serious injury or death.
(Continued)
WARNING!(Continued)
 Before using the Rear Park Assist system, it is strongly recom-
mended that the ball mount and
hitch ball assembly is discon-
nected from the vehicle when the
vehicle is not used for towing.
Failure to do so can result in in-
jury or damage to vehicles or ob-
stacles because the hitch ball will
be much closer to the obstacle
than the rear fascia when the
loudspeaker sounds the continu-
ous tone. Also, the sensors could
detect the ball mount and hitch
ball assembly, depending on its
size and shape, giving a false in-
dication that an obstacle is be-
hind the vehicle.
137

BODY LUBRICATION
Locks and all body pivot points, in-
cluding such items as seat tracks, door
hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood
hinges, should be lubricated periodi-
cally with a lithium-based grease or
equivalent, to assure quiet, easy op-
eration and to protect against rust and
wear. Prior to the application of any
lubricant, the parts concerned should
be wiped clean to remove dust and
grit; after lubricating excess oil and
grease should be removed. Particular
attention should also be given to hood
latching components to ensure proper
function. When performing other un-
derhood services, the hood latch, re-
lease mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be
lubricated twice a year, preferably in
the Fall and Spring. Apply a small
amount of a high quality lubricant
directly into the lock cylinder.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
WINDSHIELD WIPER
BLADES
Clean the rubber edges of the wiper
blades and the windshield periodi-
cally with a sponge or soft cloth and a
mild nonabrasive cleaner. This will
remove accumulations of salt or road
film.
Operation of the wipers on dry glass
for long periods may cause deteriora-
tion of the wiper blades. Always use
washer fluid when using the wipers to
remove salt or dirt from a dry wind-
shield.
Avoid using the wiper blades to re-
move frost or ice from the windshield. Keep the blade rubber out of contact
with petroleum products such as en-
gine oil, gasoline, etc.
NOTE: Life expectancy of wiper
blades varies depending on geo-
graphical area and frequency of
use. Examples of poor blade per-
formance include chattering,
marks, water lines, and wet spots.
If any of these conditions are pres-
ent, clean the wiper blades or re-
place as necessary.
Adding Washer Fluid
The windshield, rear window, and
headlamp washers share a common
fluid reservoir. It is located in the en-
gine compartment and should be
checked at regular intervals. Fill the
reservoir with windshield washer sol-
vent (not radiator antifreeze) and op-
erate the system for a few seconds to
flush out any residual water.
When refilling the washer fluid reser-
voir, apply some washer fluid to a
cloth or towel and wipe the wiper
blades clean. This will help blade per-
formance.
308

2. Remove the tail lamp assembly by
removing the two screws from the in-
board side. Use a fiber stick or similar
tool to gently pry the light on the
outboard side to disengage the two
ball studs.NOTE:
 If a screwdriver is used, make
sure a soft material is placed be-
tween the vehicle body and tool
so not to scratch the paint.
 The PRY location is best closest to the studs while dislodging
them separately.
3. Twist the socket and remove it
from the lamp assembly.
4. Pull the bulb to remove it from the
socket.
5. Replace the bulb, reinstall the
socket, and reattach the lamp assem-
bly. CENTER HIGH-MOUNTED
STOP LAMP (CHMSL)
The CHMSL uses LED lights are not
serviceable. The CHMSL must be re-
placed as an assembly, see your au-
thorized dealer.
LICENSE LAMP
There are two license plate lamps, and
they are located under the tailgate
lamp bar and above the license plate.
1. Remove the two lens assembly
mounting screws.
2. Remove the bulb from the socket.
Replace the bulb and reattach the lens
assembly.326

Thousands Of Kilometers 24 48 72 96 120 144 168 192Months 12 24 36 48 60 72 84 96
Inspect and replace PCV valve if necessary. 
Check battery charge status and possibly recharge.        
Check tire condition/wear and adjust pressure, if necessary.        
Check operation of lighting system (headlamps, direction indi-
cators, hazard warning lights, luggage compartment, passen-
ger compartment, glove compartment, instrument panel warn-
ing lights, etc.).        
Check operation of windshield washer system and adjust jets if
necessary.        
Check windshield/rear window wiper blade position/wear.        
Check cleanliness of hood and tailgate locks and cleanliness
and lubrication of linkages.        
Visually inspect condition of: exterior bodywork, underbody
protection, pipes and hoses (exhaust - fuel system - brakes),
rubber elements (boots, sleeves, bushes, etc.).        
Check conditions and wear of front disc brake pads.        
Check conditions and wear of rear disc brake pads.        
Check and, if necessary, top up fluid levels (brakes, windshield
washer, battery, engine coolant, etc.).        
Visually inspect the condition of accessory drive belt/s. 
Check exhaust gas emissions.        
Check engine management system operation (via diagnostic
socket).        
Change the automatic transmission fluid and filter. (*) 
335

Thousands Of Kilometers 20 40 60 80 100 120 140 160 180 200Months 12 24 36 48 60 72 84 96 108 120
Check battery charge status and possibly recharge.          
Check tire condition/wear and adjust pressure, if nec-
essary.          
Check operation of lighting system (headlamps, direc-
tion indicators, hazard warning lights, luggage com-
partment, passenger compartment, glove compart-
ment, instrument panel warning lights, etc.).          
Check operation of windscreen washer system and
adjust jets if necessary.          
Check windshield/rear window wiper blade position/
wear.          
Check cleanliness of hood and tailgate locks and
cleanliness and lubrication of linkages.          
Visually inspect condition of: exterior bodywork, un-
derbody protection, pipes and hoses (exhaust - fuel
system - brakes), rubber elements (boots, sleeves,
bushes, etc.).          
Check conditions and wear of front disc brake pads.          
Check conditions and wear of rear disc brake pads.          
Check and, if necessary, top up fluid levels (brakes,
windshield washer, battery, engine coolant, etc.).          
Visually inspect the condition of accessory drive belt/s.  
Check toothed timing drive belt conditions. 
Check exhaust gas emissions.          
338