2013 Lancia Flavia warning

Pressure Monitoring Telltale Light”
will turn off. The vehicle may need to
be driven for up to 20 minutes above
24 km/h in order for the TPMS to
receive this information.
Check TPMS WarningWhen a system fault is detected, a chime
will sound and the “Tire Pressure Moni-
toring Telltale Light” will flash on and
off for 75 seconds and then remain on
solid. In addition, the EVIC will display
a "CHECK TPM SYSTEM" message for
a minimum of five seconds and then
display dashes (- -) in place of the pres-
sure value to indicate which sensor is
not being received.If the ignition key is cycled, this se-
quence will repeat, providing the sys-
tem fault still exists. If the system
fault no longer exists, the “Tire Pres-
sure Monitoring Telltale Light” will
no longer flash, and the "CHECK
TPM SYSTEM" message will no lon-
ger display, and a pressure value willdisplay in place of the dashes. A sys-
tem fault can occur due to any of the
following:
1. Jamming due to electronic devices
or driving next to facilities emitting
the same Radio Frequencies as the
TPM sensors.
2. Installing some form of aftermar-
ket window tinting that affects radio
wave signals.
3. Lots of snow or ice around the
wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped
with TPM sensors.
The EVIC will also display a
"CHECK TPM SYSTEM" message
for a minimum of five seconds when a
system fault related to an incorrect
sensor location fault is detected. In
this case, the "CHECK TPM SYS-
TEM" message is then followed with a
graphic display with pressure values
still shown. This indicates that thepressure values are still being received
from the TPM sensors but they may
not be located in the correct vehicle
position. The system still needs to be
serviced as long as the "CHECK TPM
SYSTEM" message is displayed.
FUEL REQUIREMENTS
All engines are designed to meet all
emissions regulations and provide ex-
cellent fuel economy and performance
when using high quality unleaded
gasoline with a minimum research oc-
tane rating of 91.
Light spark knock at low engine
speeds is not harmful to your engine.
However, continued heavy spark
knock at high speeds can cause dam-
age and immediate service is required.
Poor quality gasoline can cause prob-
lems such as hard starting, stalling,
and hesitations. If you experience
these symptoms, try another brand of
gasoline before considering service for
the vehicle.
164

WARNING!
Carbon monoxide (CO) in exhaust
gases is deadly. Follow the precau-
tions below to prevent carbon mon-
oxide poisoning:
 Do not inhale exhaust gases. Theycontain carbon monoxide, a col-
orless and odorless gas, which can
kill. Never run the engine in a
closed area, such as a garage, and
never sit in a parked vehicle with
the engine running for an ex-
tended period. If the vehicle is
stopped in an open area with the
engine running for more than a
short period, adjust the ventila-
tion system to force fresh, outside
air into the vehicle.
 Guard against carbon monoxide with proper maintenance. Have
the exhaust system inspected ev-
ery time the vehicle is raised.
Have any abnormal conditions
repaired promptly. Until re-
paired, drive with all side win-
dows fully open. MMT IN GASOLINE
MMT is a manganese containing me-
tallic additive that is blended into
some gasoline to increase octane.
Gasoline blended with MMT provides
no performance advantage beyond
gasoline of the same octane number
without MMT. Gasoline blended with
MMT reduces spark plug life and re-
duces emission system performance in
some vehicles. The manufacturer rec-
ommends that gasoline without MMT
be used in your vehicle. The MMT
content of gasoline may not be indi-
cated on the gasoline pump; therefore,
you should ask your gasoline retailer
whether or not his/her gasoline con-
tains MMT.
MATERIALS ADDED TO
FUEL
Besides using unleaded gasoline with
the proper octane rating, gasolines
that contain detergents, corrosion and
stability additives are recommended.
Using gasolines that have these addi-
tives will help improve fuel economy,
reduce emissions, and maintain ve-
hicle performance.
Indiscriminate use of fuel system
cleaning agents should be avoided.
Many of these materials intended for
gum and varnish removal may con-
tain active solvents or similar ingredi-
ents. These can harm fuel system gas-
ket and diaphragm materials.
166

WARNING!
Carbon monoxide (CO) in exhaust
gases is deadly. Follow the precau-
tions below to prevent carbon mon-
oxide poisoning:
 Do not inhale exhaust gases. Theycontain carbon monoxide, a col-
orless and odorless gas which can
kill. Never run the engine in a
closed area, such as a garage, and
never sit in a parked vehicle with
the engine running for an ex-
tended period of time. If the ve-
hicle is stopped in an open area
with the engine running for more
than a short period, adjust the
ventilation system to force fresh,
outside air into the vehicle.
Guard against carbon monoxide
with proper maintenance. Have
the exhaust system inspected every
time the vehicle is raised. Have any
abnormal conditions repaired
promptly. Until repaired, drive
with all side windows fully open.
(Continued)
WARNING! (Continued)
 Keep the liftgate closed when driving your vehicle to prevent
carbon monoxide and other poi-
sonous exhaust gases from enter-
ing the vehicle.
ADDING FUEL
FUEL FILLER CAP
(GAS CAP)
The gas cap is behind the fuel filler
door, on the left rear quarter panel of
the vehicle. If the gas cap is lost or
damaged, be sure the replacement cap
is for use with this vehicle. After removing the gas cap, place the
gas cap tether cable over a hook on
the inside of the fuel door. This keeps
the gas cap suspended away from and
protects the vehicle's surface.
NOTE: If the gas cap is lost or
damaged, be sure the replacement
cap is for use with this vehicle.
Fuel Filler Door
Tether Cable
167

CAUTION!
 Damage to the fuel system oremission control system could re-
sult from using an improper fuel
tank filler tube cap (gas cap).
 A poorly fitting gas cap may cause the “Malfunction Indicator
Light (MIL)” to turn on.
 To avoid fuel spillage and over- filling, do not “top off” the fuel
tank after filling. When the fuel
nozzle “clicks” or shuts off, the
fuel tank is full.WARNING!
 Never have any smoking materi-als lit in or near the vehicle when
the gas cap is removed or the tank
is being filled.
 A fire may result if gasoline is pumped into a portable container
that is inside of a vehicle. You
could be burned. Always place
gas containers on the ground
while filling. NOTE:
 Tighten the gas cap until you
hear a “clicking” sound. This is
an indication that the gas cap is
tightened properly. The MIL in
the instrument cluster may turn
on if the gas cap is not secured
properly. Make sure that the gas
cap is tightened each time the
vehicle is refueled.
 When the fuel nozzle “clicks” or shuts off, the fuel tank is full.
LOOSE FUEL FILLER CAP
MESSAGE
If the vehicle diagnostic system deter-
mines that the fuel filler cap is loose,
improperly installed, or damaged, a
“CHECK GAS CAP” message will be
displayed in the EVIC (Electronic Ve-
hicle Information Center). Refer to “Electronic Vehicle Information Cen-
ter” in “Understanding Your Instru-
ment Panel” for further information.
Tighten the fuel filler cap properly
and press the odometer reset button to
turn the message off. If the problem
continues, the message will appear
the next time the vehicle is started.
Refer to “Onboard Diagnostic Sys-
tem” in “Maintaining Your Vehicle”
for further information.
NOTE: If the gas cap is lost or
damaged, be sure the replacement
cap is for use with this vehicle.
TRAILER TOWING
Trailer towing with this vehicle is not
recommended.
168

6
WHAT TO DO IN EMERGENCIES
 HAZARD WARNING FLASHERS . . . . . . . . . . . . .172
 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . . . .172  ENGINE OIL OVERHEATING . . . . . . . . . . . . . .173
 TIREFIT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT STORAGE . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT KIT COMPONENTS ANDOPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT USAGE PRECAUTIONS . . . . . . . . . . .174
 SEALING A TIRE WITH TIREFIT. . . . . . . . . . .175
 JUMP-STARTING . . . . . . . . . . . . . . . . . . . . . . . . .179
 PREPARATIONS FOR JUMP-START . . . . . . . . .180
 JUMP-STARTING PROCEDURE . . . . . . . . . . . .181
 FREEING A STUCK VEHICLE . . . . . . . . . . . . . . .182
 SHIFT LEVER OVERRIDE . . . . . . . . . . . . . . . . .183
 TOWING A DISABLED VEHICLE . . . . . . . . . . . .184
 AUTOMATIC TRANSMISSION . . . . . . . . . . . . .185
 WITHOUT THE IGNITION KEY . . . . . . . . . . . .185
171

HAZARD WARNING
FLASHERS
The Hazard Warning flasher switch is
located on the instrument panel, be-
low the radio.Press the switch to turn on the
Hazard Warning flasher.
When the switch is activated, all di-
rectional turn signals will flash on and
off to warn oncoming traffic of an
emergency. Press the switch a second
time to turn off the Hazard Warning
flashers.
This is an emergency warning system
and it should not be used when the
vehicle is in motion. Use it when your
vehicle is disabled and it is creating a
safety hazard for other motorists.
When you must leave the vehicle to
seek assistance, the Hazard Warning
flashers will continue to operate even
though the ignition is placed in the
OFF position.
NOTE: With extended use the
Hazard Warning flashers may
wear down your battery. IF YOUR ENGINE
OVERHEATS
In any of the following situations, you
can reduce the potential for overheat-
ing by taking the appropriate action.
 On the highways — Slow down.
 In city traffic — While stopped, put
transaxle in NEUTRAL, but do not
increase engine idle speed.
CAUTION!
Driving with a hot cooling system
could damage your vehicle. If tem-
perature gauge reads “H”, pull over
and stop the vehicle with the engine
at idle, when safe. Turn the air con-
ditioner off and wait until the
pointer drops back into the normal
range. After appropriate action has
been taken, if the pointer remains
on the “H”, turn the engine off im-
mediately, and call for service. NOTE: There are steps that you
can take to slow down an impend-
ing overheat condition:
 If your air conditioner (A/C) is
on, turn it off. The A/C system
adds heat to the engine cooling
system and turning the A/C off
can help remove this heat.
 You can also turn the tempera- ture control to maximum heat,
the mode control to floor and the
blower control to high. This al-
lows the heater core to act as a
supplement to the radiator and
aids in removing heat from the
engine cooling system.
WARNING!
You or others can be badly burned
by hot engine coolant (antifreeze)
or steam from your radiator. If you
see or hear steam coming from un-
der the hood, do not open the hood
until the radiator has had time to
cool. Never try to open a cooling
system pressure cap when the ra-
diator or coolant bottle is hot.
172

Using The Power Button
Push and release the Power
Button (4) once to turn On
the TIREFIT kit. Push and
release the Power Button (4)
again to turn Off the TIREFIT kit.
Using The Deflation Button
Press the Deflation But-
ton (2) to reduce the air pres-
sure in the tire if it becomes
over-inflated.
TIREFIT USAGE
PRECAUTIONS
Replace the TIREFIT Sealant Bottle
(1) and Sealant Hose (6) prior to the
expiration date (printed on the
bottle label) to assure optimum op-
eration of the system. Refer to
“Sealing a Tire with TIREFIT” sec-
tion (F) “Sealant Bottle and Hose
Replacement”. The Sealant Bottle (1) and Sealant Hose (6) are a one tire application
use. After each use, always replace
these components immediately at
an authorized dealer.  When the TIREFIT sealant is in a
liquid form, clean water, and a
damp cloth will remove the mate-
rial from the vehicle or tire and
wheel components. Once the seal-
ant dries, it can easily be peeled off
and properly discarded.
 For optimum performance, make sure the valve stem on the wheel is
free of debris before connecting the
TIREFIT kit.

You can use the TIREFIT air pump to
inflate bicycle tires. The kit also
comes with two needles, located in
the Accessory Storage Compartment
(on the bottom of the air pump) for
inflating sport balls, rafts, or similar
inflatable items. However, use only
the Air Pump Hose (7) and make sure
the Mode Select Knob (5) is in the Air
Mode when inflating such items to
avoid injecting sealant into them.
The TIREFIT Sealant is only in-
tended to seal punctures less than 6
mm diameter in the tread of your
vehicle. Do not lift or carry the TIREFIT kit by the hoses.
WARNING!
 Do not attempt to seal a tire onthe side of the vehicle close to
traffic. Pull far enough off the
road to avoid the danger of being
hit when using the TIREFIT kit.
 Do not use TIREFIT or drive the
vehicle under the following cir-
cumstances:–
If the puncture in the tire tread
is approximately 6 mm or
larger.– If the tire has any sidewall damage.
– If the tire has any damage from
driving with extremely low tire
pressure.
– If the tire has any damage from
driving on a flat tire.
– If the wheel has any damage.
– If you are unsure of the condi- tion of the tire or the wheel.
 Keep TIREFIT away from open flame or heat source.
 A loose TIREFIT kit thrown for- ward in a collision or hard stop
could endanger the occupants of
(Continued)
174

WARNING!(Continued)
the vehicle. Always stow the
TIREFIT kit in the place pro-
vided. Failure to follow these
warnings can result in injuries
that are serious or fatal to you,
your passengers, and others
around you.
 Take care not to allow the con- tents of TIREFIT to come in con-
tact with hair, eyes, or clothing.
TIREFIT is harmful if inhaled,
swallowed, or absorbed through
the skin: It causes skin, eye, and
respiratory irritation. Flush im-
mediately with plenty of water if
there is any contact with eyes or
skin. Change clothing as soon as
possible, if there is any contact
with clothing.
 TIREFIT Sealant solution con-
tains latex. In case of allergic re-
action or rash, consult a physi-
cian immediately. Keep TIREFIT
out of reach of children. If swal-
lowed, rinse mouth immediately
with plenty of water and drink
(Continued)
WARNING!(Continued)
plenty of water. Do not induce
vomiting! Consult a physician
immediately.
 Use the gloves provided in the Accessory Storage Compartment
(located on the bottom of the air
pump) when operating the TIRE-
FIT kit.
SEALING A TIRE WITH
TIREFIT
If the sealant (white fluid) does
flow through the Sealant Hose (6):
1.Continue to operate the pump until
sealant is no longer flowing through
hose (typically takes 30 - 70 seconds).
As the sealant flows through the Sealant
Hose (6), the Pressure Gauge (3) can
read as high as 5 Bar. The Pressure
Gauge (3) will decrease quickly from
approximately 70 psi (5 Bar) to the
actual tire pressure when the Sealant
Bottle (1) is empty.
2. The pump will start to inject air
into the tire immediately after the
Sealant Bottle (1) is empty. Continue
to operate the pump and inflate the
tire to the pressure indicated on the
tire pressure label on the driver-side
latch pillar (recommended pressure).
Check the tire pressure by looking at
the Pressure Gauge (3).If the tire does not inflate to at least
1.8 Bar pressure within 15 minutes: The tire is too badly damaged. Do
not attempt to drive the vehicle fur-
ther. Call for assistance.
NOTE: If the tire becomes over-
inflated, press the Deflation But-
ton to reduce the tire pressure to
the recommended inflation pres-
sure before continuing.
If the tire inflates to the recom-
mended pressure or is at least 1.8
Bar pressure within 15 minutes:
1. Press the Power Button (4) to turn
off the TIREFIT kit.
175