2013 JEEP GRAND CHEROKEE window

WARNING!(Continued)
•When leaving the vehicle, always remove
the key fob and lock your vehicle.
• Never leave children alone in a vehicle, or
with access to an unlocked vehicle. Allow-
ing children to be in a vehicle unattended
is dangerous for a number of reasons.
A child or others could be seriously or
fatally injured.
• Children should be warned not to touch the
parking brake, brake pedal or the shift
lever.
•
Do not leave the key fob in or near the
vehicle (or in a location accessible to chil-
dren), and do not leave Keyless Enter-N-
Go™ in the ACC or ON/RUN position.
A child could operate power windows, other
controls, or move the vehicle.
Key Ignition Park InterlockThis vehicle is equipped with a Key Ignition Park
Interlock which requires the shift lever to be in
PARK before the ignition switch can be turned
to the OFF position. The key fob can only be
removed from the ignition when the ignition is in
the OFF position, and the shift lever is locked in
PARK whenever the ignition switch is in the
OFF position.
NOTE:
If a malfunction occurs, the system will trap
the key fob in the ignition switch to warn you
that this safety feature is inoperable. The
engine can be started and stopped but the
key fob cannot be removed until you obtain
service.
Brake/Transmission Shift Interlock
System
This vehicle is equipped with a Brake Transmis-
sion Shift Interlock system (BTSI) that holds the
shift lever in PARK unless the brakes are ap-
plied. To shift the transmission out of PARK, the
ignition switch must be turned to the ON/RUN
position (engine running or not) and the brake
pedal must be pressed.
Five-Speed Automatic Transmission
(3.6L and 3.0L Diesel Engine) — If
Equipped
The shift lever position display (located in the
instrument cluster) indicates the transmission
gear range. You must press the brake pedal to
move the shift lever out of PARK (refer to
“Brake/Transmission Shift Interlock System” in
this section). To drive, move the shift lever from
PARK or NEUTRAL to the DRIVE position.
The electronically-controlled transmission pro-
vides a precise shift schedule. The transmission
electronics are self-calibrating; therefore, the
first few shifts on a new vehicle may be some-
what abrupt. This is a normal condition, and
precision shifts will develop within a few hun-
dred miles (kilometers).
Only shift from DRIVE to PARK or REVERSE
when the accelerator pedal is released and the
vehicle is stopped. Be sure to keep your foot on
the brake pedal when shifting between these
gears.
226

WARNING!(Continued)
•It is dangerous to shift out of PARK or
NEUTRAL if the engine speed is higher
than idle speed. If your foot is not firmly
pressing the brake pedal, the vehicle could
accelerate quickly forward or in reverse.
You could lose control of the vehicle and
hit someone or something. Only shift into
gear when the engine is idling normally
and your foot is firmly pressing the brake
pedal.
• Unintended movement of a vehicle could
injure those in or near the vehicle. As with
all vehicles, you should never exit a ve-
hicle while the engine is running. Before
exiting a vehicle, always apply the parking
brake, shift the transmission into PARK
turn the engine OFF, and remove the key
fob. When the ignition is in the LOCK/OFF
position, the shift lever is locked in PARK,
securing the vehicle against unwanted
movement.
(Continued)
WARNING!(Continued)
•When leaving the vehicle, always remove
the key fob and lock your vehicle.
• Never leave children alone in a vehicle, or
with access to an unlocked vehicle.
• Allowing children to be in a vehicle unat-
tended is dangerous for a number of rea-
sons. A child or others could be seriously
or fatally injured. Children should be
warned not to touch the parking brake,
brake pedal or the shift lever.
• Do not leave the key fob in or near the
vehicle (or in a location accessible to chil-
dren), and do not leave Keyless Enter-N-
Go™ in the ACC or ON/RUN position. A
child could operate power windows, other
controls, or move the vehicle.
CAUTION!
• Before moving the shift lever out of PARK,
you must turn the ignition switch from the
OFF position to the ON/RUN position, and
also press the brake pedal. Otherwise,
damage to the shift lever could result.
• DO NOT race the engine when shifting
from PARK or NEUTRAL into another gear
range, as this can damage the drivetrain.
The following indicators should be used to
ensure that you have engaged the shift lever
into the PARK position:
• When shifting into PARK, firmly move the
shift lever all the way forward and to the left
until it stops and is fully seated.
• Look at the shift lever position display and
verify that it indicates the PARK position.
• With brake pedal released, verify that the
shift lever will not move out of PARK.
228

WARNING!(Continued)
•Do not leave the key fob in or near the
vehicle (or in a location accessible to chil-
dren), and do not leave Keyless Enter-N-
Go™ in the ACC or ON/RUN position.
A child could operate power windows,
other controls, or move the vehicle.
CAUTION!
• Before moving the shift lever out of PARK,
you must turn the ignition switch from the
OFF position to the ON/RUN position, and
also press the brake pedal. Otherwise,
damage to the shift lever could result.
• DO NOT race the engine when shifting
from PARK or NEUTRAL into another gear
range, as this can damage the drivetrain. The following indicators should be used to
ensure that you have engaged the shift lever
into the PARK position:
•
When shifting into PARK, firmly move the
shift lever all the way forward and to the left
until it stops and is fully seated.
• Look at the shift lever position display and
verify that it indicates the PARK position.
• With brake pedal released, verify that the
shift lever will not move out of PARK.
REVERSE
This range is for moving the vehicle backward.
Shift into REVERSE only after the vehicle has
come to a complete stop.
NEUTRAL
Use this range when the vehicle is standing for
prolonged periods with the engine running. The
engine may be started in this range. Apply the
parking brake and shift the transmission into
PARK if you must leave the vehicle.
WARNING!
Do not coast in NEUTRAL and never turn off
the ignition to coast down a hill. These are
unsafe practices that limit your response to
changing traffic or road conditions. You might
lose control of the vehicle and have a collision.
CAUTION!
Towing the vehicle, coasting, or driving for
any other reason with the transmission in
NEUTRAL can cause severe transmission
damage. Refer to “Recreational Towing” in
“Starting And Operating” and “Towing A Dis-
abled Vehicle” in “What To Do In Emergen-
cies” for further information.
233

•This light only shows that the parking
brake is applied. It does not show the
degree of brake application.
When parking on a hill, it is important to turn the
front wheels toward the curb on a downhill
grade and away from the curb on an uphill
grade. Apply the parking brake before placing
the shift lever in PARK, otherwise the load on
the transmission locking mechanism may make
it difficult to move the shift lever out of PARK.
The parking brake should always be applied
whenever the driver is not in the vehicle.
WARNING!
• Never use the PARK position as a substi-
tute for the parking brake. Always apply
the parking brake fully when parked to
guard against vehicle movement and pos-
sible injury or damage.
(Continued)
WARNING!(Continued)
•When leaving the vehicle, always remove
the key fob from the ignition and lock your
vehicle. Never leave children alone in a
vehicle, or with access to an unlocked
vehicle. Allowing children to be in a vehicle
unattended is dangerous for a number of
reasons. A child or others could be seri-
ously or fatally injured. Children should be
warned not to touch the parking brake,
brake pedal or the shift lever.
• Do not leave the key fob in or near the
vehicle (or in a location accessible to chil-
dren), and do not leave the ignition of a
vehicle equipped with Keyless Enter-N-
Go™ in the ACC or ON/RUN position. A
child could operate power windows, other
controls, or move the vehicle.
• Be sure the parking brake is fully disen-
gaged before driving; failure to do so can
lead to brake failure and a collision.
(Continued)
WARNING!(Continued)
•Always fully apply the parking brake when
leaving your vehicle, or it may roll and
cause damage or injury. Also be certain to
leave the transmission in PARK. Failure to
do so may allow the vehicle to roll and
cause damage or injury.
CAUTION!
If the “Brake Warning Light” remains on with
the parking brake released, a brake system
malfunction is indicated. Have the brake
system serviced by an authorized dealer
immediately.
251

The Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds, and remain on
solid when a system fault is detected. In addi-
tion, a “SERVICE TPM SYSTEM” message
may be displayed for approximately 5 seconds
when a system fault is detected, and a chime
will sound. If the ignition switch is cycled, this
sequence will repeat, providing the system fault
still exists. The Tire Pressure Monitoring Telltale
Light will turn off when the fault condition no
longer exists. A system fault can occur by any of
the following:
1. Jamming due to electronic devices or driving
next to facilities emitting the same Radio Fre-
quencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals.
3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.NOTE:There is no tire pressure monitoring sensor in
the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire, in place of a road tire, that has a
pressure below the low-pressure warning
limit, upon the next ignition switch cycle, a
chime will sound, a “LOW TIRE PRESSURE”
message will be displayed in the instrument
cluster for a minimum of five seconds, an
Inflate to XXX
message will be displayed and
the Tire Pressure Monitoring Telltale Light will
turn ON. After driving the vehicle for up to 20
minutes above 15 mph (24 km/h), the Tire
Pressure Monitoring Telltale Light will flash on
and off for 75 seconds and then remain on
solid. In addition, a “SERVICE TPM SYSTEM”
message will be displayed for a minimum of
five seconds. For each subsequent ignition
switch cycle, a chime will sound, a “SERVICE
TPM SYSTEM” message will be displayed for
a minimum of five seconds, and the Tire Pres-
sure Monitoring Telltale Light will flash on and
off for 75 seconds and then remain on solid. Once you repair or replace the original road
tire, and reinstall it on the vehicle in place of
the spare tire, the TPMS will update automati-
cally and the Tire Pressure Monitoring Telltale
Light will turn OFF, as long as no tire pressure
is below the low-pressure warning limit in any
of the four active road tires. The vehicle may
need to be driven for up to 20 minutes above
15 mph (24 km/h) in order for the TPMS to
receive this information.
Premium System – If EquippedThe Tire Pressure Monitor System (TPMS)
uses wireless technology with wheel rim-
mounted electronic sensors to monitor tire pres-
sure levels. Sensors, mounted to each wheel as
part of the valve stem, transmit tire pressure
readings to the Receiver Module.
NOTE:
It is particularly important, for you to regu-
larly check the tire pressure in all of your
tires and to maintain the proper pressure.
269

If the ignition switch is cycled, this sequence will
repeat, providing the system fault still exists. If
the system fault no longer exists, the Tire Pres-
sure Monitoring Telltale Light will no longer
flash, the"SERVICE TPM SYSTEM" message
will not be present, and a pressure value will be
displayed instead of dashes. A system fault can
occur by any of the following:
1. Jamming due to electronic devices or driving
next to facilities emitting the same Radio Fre-
quencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.
The EVIC will also display a
"SERVICE TPM
SYSTEM" message for a minimum of five sec-
onds when a system fault is detected possibly
related to an incorrect sensor location fault. In
this case, the "SERVICE TPM SYSTEM" mes-
sage is then followed by a graphic display, with
pressure values still shown. This indicates the
pressure values are still being received from the
TPM Sensors but they may not be located in the
correct vehicle position. However, the system
still needs to be serviced as long as the "SER-
VICE TPM SYSTEM" message exists.
NOTE:
There is no tire pressure monitoring sensor
in the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire in place of a road tire that has a
pressure below the low-pressure warning limit, upon the next ignition switch cycle, the
Tire Pressure Monitoring Telltale Light will
remain ON, a chime will sound, and the EVIC
will still display a “flashing” pressure value
in the graphic display and an
Inflate to
XXX kPa message will be displayed. After
driving the vehicle for up to 20 minutes
above 15 mph (24 km/h), the Tire Pressure
Monitoring Telltale Light will flash on and off
for 75 seconds and then remain on solid. In
addition, the EVIC will display a “SERVICE
TPM SYSTEM message for five seconds
and then display dashes (- -) in place of the
pressure value. For each subsequent igni-
tion switch cycle, a chime will sound, the
Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds and then
remain on solid, and the EVIC will display a
SERVICE TPM SYSTEM message for five
seconds and then display dashes (- -) in
place of the pressure value. Once you repair
or replace the original road tire, and reinstall
it on the vehicle in place of the spare tire, the
TPMS will update automatically.
271

WARNING!
Carbon monoxide (CO) in exhaust gases is
deadly. Follow the precautions below to pre-
vent carbon monoxide poisoning:
•Do not inhale exhaust gases. They contain
carbon monoxide, a colorless and odor-
less gas which can kill. Never run the
engine in a closed area, such as a garage,
and never sit in a parked vehicle with the
engine running for an extended period. If
the vehicle is stopped in an open area with
the engine running for more than a short
period, adjust the ventilation system to
force fresh, outside air into the vehicle.
• Guard against carbon monoxide with
proper maintenance. Have the exhaust
system inspected every time the vehicle is
raised. Have any abnormal conditions re-
paired promptly. Until repaired, drive with
all side windows fully open.
(Continued)
WARNING!(Continued)
•Keep the liftgate closed when driving your
vehicle to prevent carbon monoxide and
other poisonous exhaust gases from en-
tering the vehicle.
FUEL REQUIREMENTS —
DIESEL ENGINE
Use good quality diesel fuel from a reputable
supplier. For most year-round service, No. 2
diesel fuel, meeting ASTM specification D-975
Grade S15, will provide good performance. If
the vehicle is exposed to extreme cold (below
20° F or -7° C), or is required to operate at
colder-than-normal conditions for prolonged pe-
riods, use climatized No. 2 diesel fuel or dilute
the No. 2 diesel fuel with 50% No. 1 diesel fuel. This will provide better protection from fuel
gelling or wax-plugging of the fuel filters.
This
vehicle must only use premium diesel fuel
that meets the requirements of EN 590. Bio-
diesel blends that meet EN 590 may also be
used.
CAUTION!
The manufacturer requires that you must fuel
this vehicle with Ultra Low Sulfur Highway
Diesel fuel (15 ppm Sulfur maximum) and
prohibits the use of Low Sulfur Highway Diesel
fuel (500 ppm Sulfur maximum) to avoid dam-
age to the emissions control system.
275

Rear Wiper Blade Removal/Installation
1. Lift the pivot cap on the rear wiper arm
upward, this will allow the rear wiper blade to be
raised off of the liftgate glass.
NOTE:
The rear wiper arm cannot be raised fully
upward unless the pivot cap is raised first.
2. Lift the rear wiper arm upward to raise the
wiper blade off of the liftgate glass.3. Grab the bottom of the wiper blade and
rotate it forward to unsnap the blade pivot pin
from the wiper blade holder.
4. Install the wiper blade pivot pin into the wiper
blade holder at the end of the wiper arm, and
firmly press the wiper blade until it snaps into
place.
5. Lower the wiper blade and snap the pivot
cap into place.Adding Washer FluidOn vehicles equipped with a Electronic Vehicle
Information Center (EVIC), the low washer fluid
level will be indicated. When the sensor detects
a low fluid level, the windshield will light on the
vehicle graphic outline and the “WASHER
FLUID LOW” message will be displayed.
The fluid reservoir for the windshield washers
and the rear window washer is shared. The fluid
reservoir is located in the engine compartment,
be sure to check the fluid level at regular
intervals. Fill the reservoir with windshield
washer solvent only (not radiator antifreeze).
When refilling the washer fluid reservoir, take
some washer fluid and apply it to a cloth or
towel and wipe clean the wiper blades, this will
help blade performance. To prevent freeze-up
of your windshield washer system in cold
weather, select a solution or mixture that meets
or exceeds the temperature range of your cli-
mate. This rating information can be found on
most washer fluid containers.
1 — Wiper Arm
2 — Pivot Cap
1 — Wiper Blade
2 — Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Blade Holder
319