2013 JEEP GRAND CHEROKEE wiper blades

Windshield Wiper OperationRotate the end of the lever to one of the first four
detent positions for intermittent settings, the fifth
detent for low wiper operation and the sixth
detent for high wiper operation.
CAUTION!
Always remove any buildup of snow that pre-
vents the windshield wiper blades from return-
ing to the “park” position. If the windshield wiper
switch is turned off, and the blades cannot
return to the “park” position, damage to the
wiper motor may occur.
Intermittent Wiper SystemUse one of the four intermittent wiper settings
when weather conditions make a single wiping
cycle, with a variable delay between cycles,
desirable. At driving speeds above 10 mph
(16 km/h), the delay can be regulated from a
maximum of approximately 18 seconds be-
tween cycles (first detent), to a cycle every one
second (fourth detent).
NOTE:
If the vehicle is moving less than 10 mph
(16 km/h), delay times will be doubled.Windshield Washer OperationTo use the washer, push on the end of the lever
(toward the steering wheel) and hold while
spray is desired. If the lever is pushed while in
the intermittent setting, the wipers will turn on
and operate for several wipe cycles after the
end of the lever is released, and then resume
the intermittent interval previously selected.
If the end of the lever is pushed while the wipers
are in the off position, the wipers will operate for
several wipe cycles, then turn off.
Windshield Wiper Operation
Intermittent Wiper OperationWindshield Washer Operation
11 3

The Rain Sensing system has protection fea-
tures for the wiper blades and arms, and will not
operate under the following conditions:
•Low Ambient Temperature — When the
ignition is first turned ON, the Rain Sensing
system will not operate until the wiper switch
is moved, vehicle speed is greater than
0 mph (0 km/h), or the outside temperature is
greater than 32°F (0°C).
• Transmission In NEUTRAL Position —
When the ignition is ON, and the transmis-
sion is in the NEUTRAL position, the Rain
Sensing system will not operate until the
wiper switch is moved, vehicle speed is
greater than 5 mph (8 km/h), or the shift lever
is moved out of the NEUTRAL position.
Remote Start Mode Inhibit — On vehicles
equipped with Remote Starting system, Rain
Sensing wipers are not operational when the
vehicle is in the remote start mode. Once the
operator is in the vehicle and has placed the
ignition switch in the RUN position, rain sensing
wiper operation can resume, if it has been
selected, and no other inhibit conditions (men-
tioned previously) exist.TILT/TELESCOPING STEERING
COLUMN
This feature allows you to tilt the steering col-
umn upward or downward. It also allows you to
lengthen or shorten the steering column. The
tilt/telescoping lever is located below the steer-
ing wheel at the end of the steering column. To unlock the steering column, push the lever
downward (toward the floor). To tilt the steering
column, move the steering wheel upward or
downward as desired. To lengthen or shorten
the steering column, pull the steering wheel
outward or push it inward as desired. To lock the
steering column in position, push the lever
upward until fully engaged.
WARNING!
Do not adjust the steering column while
driving. Adjusting the steering column while
driving or driving with the steering column
unlocked, could cause the driver to lose
control of the vehicle. Failure to follow this
warning may result in serious injury or death.
Tilt/Telescoping Lever
11 5

7
MAINTAINING YOUR VEHICLE
•ENGINE COMPARTMENT — 3.6L ...................309
• ENGINE COMPARTMENT — 5.7L ...................310
• ENGINE COMPARTMENT — 3.0L DIESEL ..............311
• ONBOARD DIAGNOSTIC SYSTEM (OBD II) .............312
•Loose Fuel Filler Cap Message ...................312•REPLACEMENT PARTS .........................312
• MAINTENANCE PROCEDURES ....................312
•Engine Oil – Gasoline Engines ....................313
• Engine Oil – Diesel Engine ..................... .314
• Synthetic Engine Oils ........................ .315
• Materials Added To Engine Oil ....................315
• Disposing Of Used Engine Oil And Oil Filters ...........315
• Engine Oil Filter ........................... .315
• Engine Air Cleaner Filter ...................... .315
• Maintenance-Free Battery ...................... .316
• Air Conditioner Maintenance .................... .316
• Body Lubrication ........................... .318
• Windshield Wiper Blades ...................... .318
• Adding Washer Fluid ........................ .319
307

5. Remove the A/C air filter by pulling it straight
out of the housing.
6. Install the A/C air filter with the arrow on the
filter pointing toward the floor. When installing
the filter cover, make sure the retaining tabs
fully engage the cover.
CAUTION!
The A/C air filter is identified with an arrow to
indicate airflow direction through the filter.
Failure to properly install the filter will result
in the need to replace it more often.
7. Rotate the glove compartment door back
into position.
Body LubricationLocks and all body pivot points, including such
items as seat tracks, door hinge pivot points
and rollers, liftgate, tailgate, sliding doors and
hood hinges, should be lubricated periodically
with a lithium based grease, such as MOPAR®
Spray White Lube to assure quiet, easy opera-
tion and to protect against rust and wear. Prior
to the application of any lubricant, the parts
concerned should be wiped clean to remove
dust and grit; after lubricating excess oil and
grease should be removed. Particular attention
should also be given to hood latching compo-
nents to ensure proper function. When perform-
ing other underhood services, the hood latch,
release mechanism and safety catch should be
cleaned and lubricated.
The external lock cylinders should be lubricated
twice a year, preferably in the Fall and Spring.
Apply a small amount of a high quality lubricant,
such as MOPAR® Lock Cylinder Lubricant di-
rectly into the lock cylinder.Windshield Wiper BladesClean the rubber edges of the wiper blades and
the windshield periodically with a sponge or soft
cloth and a mild nonabrasive cleaner. This will
remove accumulations of salt or road film.
Operation of the wipers on dry glass for long
periods may cause deterioration of the wiper
blades. Always use washer fluid when using the
wipers to remove salt or dirt from a dry wind-
shield.
Avoid using the wiper blades to remove frost or
ice from the windshield. Keep the blade rubber
out of contact with petroleum products such as
engine oil, gasoline, etc.
NOTE:
Life expectancy of wiper blades varies de-
pending on geographical area and fre-
quency of use. Poor performance of blades
may be present with chattering, marks, wa-
ter lines or wet spots. If any of these condi-
tions are present, clean the wiper blades or
replace as necessary.
318

Rear Wiper Blade Removal/Installation
1. Lift the pivot cap on the rear wiper arm
upward, this will allow the rear wiper blade to be
raised off of the liftgate glass.
NOTE:
The rear wiper arm cannot be raised fully
upward unless the pivot cap is raised first.
2. Lift the rear wiper arm upward to raise the
wiper blade off of the liftgate glass.3. Grab the bottom of the wiper blade and
rotate it forward to unsnap the blade pivot pin
from the wiper blade holder.
4. Install the wiper blade pivot pin into the wiper
blade holder at the end of the wiper arm, and
firmly press the wiper blade until it snaps into
place.
5. Lower the wiper blade and snap the pivot
cap into place.Adding Washer FluidOn vehicles equipped with a Electronic Vehicle
Information Center (EVIC), the low washer fluid
level will be indicated. When the sensor detects
a low fluid level, the windshield will light on the
vehicle graphic outline and the “WASHER
FLUID LOW” message will be displayed.
The fluid reservoir for the windshield washers
and the rear window washer is shared. The fluid
reservoir is located in the engine compartment,
be sure to check the fluid level at regular
intervals. Fill the reservoir with windshield
washer solvent only (not radiator antifreeze).
When refilling the washer fluid reservoir, take
some washer fluid and apply it to a cloth or
towel and wipe clean the wiper blades, this will
help blade performance. To prevent freeze-up
of your windshield washer system in cold
weather, select a solution or mixture that meets
or exceeds the temperature range of your cli-
mate. This rating information can be found on
most washer fluid containers.
1 — Wiper Arm
2 — Pivot Cap
1 — Wiper Blade
2 — Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Blade Holder
319

Vehicle Storage.............213, 335
Vehicle Theft Alarm (Security Alarm) .....16
Viscosity, Engine Oil .............314
Voice Recognition System (VR) .......91
Warning Flasher, Hazard ..........294
Warning, Roll Over ...............4
Warnings and Cautions .............8
Washers, Windshield ..........112,319
Washing Vehicle ...............329
Wheel and Wheel Trim ............329
Wheel and Wheel Trim Care ........329Wind Buffeting
...........28, 143, 145
Window Fogging ...............213
Windows ....................26
Power ...................26
Windshield Defroster .............60
Windshield Washers .............112
Fluid ...................319
Windshield Wiper Blades ..........318
Windshield Wipers ..............112
Wiper Blade Replacement ..........318
Wipers, Intermittent ..............113
Wipers, Rain Sensitive ............114
402