2013 JEEP GRAND CHEROKEE tire pressure

NOTE:
•The TPMS is not intended to replace nor-
mal tire care and maintenance, or to pro-
vide warning of a tire failure or condition.
• The TPMS should not be used as a tire
pressure gauge while adjusting your tire
pressure.
• Driving on a significantly under-inflated
tire causes the tire to overheat and can
lead to tire failure. Under-inflation also
reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and
stopping ability.
• The TPMS is not a substitute for proper
tire maintenance, and it is the driver’s
responsibility to maintain correct tire
pressure using an accurate tire gauge,
even if under-inflation has not reached
the level to trigger illumination of the Tire
Pressure Monitoring Telltale Light.
• Seasonal temperature changes will affect
tire pressure, and the TPMS will monitor
the actual tire pressure in the tire.Base SystemThe Tire Pressure Monitor System (TPMS)
uses wireless technology with wheel rim-
mounted electronic sensors to monitor tire pres-
sure levels. Sensors, mounted to each wheel as
part of the valve stem, transmit tire pressure
readings to the Receiver Module.
NOTE:
It is particularly important, for you to regu-
larly check the tire pressure in all of your
tires, and to maintain the proper pressure.
The TPMS consists of the following compo-
nents:
•Receiver Module
• Four Tire Pressure Monitoring Sensors
• Tire Pressure Monitoring Telltale Light
A low spare tire will not cause the Tire Pressure
Monitoring Telltale Light to illuminate, a warning
message to appear, or the chime to sound. The Tire Pressure Monitoring Telltale
Light will illuminate in the instrument
cluster, a “LOW TIRE PRESSURE”
message will display in the instrument
cluster for 5 seconds, an "Inflate to XXX"mes-
sage will be displayed and an audible chime will
be activated, when one or more of the four
active road tire pressures are low. Should this
occur, you should stop as soon as possible,
check the inflation pressure of each tire on your
vehicle, and inflate each tire to the vehicle’s
recommended cold placard pressure value dis-
played in the "Inflate to XXX" message. The
system will automatically update and the Tire
Pressure Monitoring Telltale Light will extin-
guish, once the updated tire pressures have
been received. The vehicle may need to be
driven for up to 20 minutes above 15 mph
(24 km/h) to receive this information.
268

The Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds, and remain on
solid when a system fault is detected. In addi-
tion, a “SERVICE TPM SYSTEM” message
may be displayed for approximately 5 seconds
when a system fault is detected, and a chime
will sound. If the ignition switch is cycled, this
sequence will repeat, providing the system fault
still exists. The Tire Pressure Monitoring Telltale
Light will turn off when the fault condition no
longer exists. A system fault can occur by any of
the following:
1. Jamming due to electronic devices or driving
next to facilities emitting the same Radio Fre-
quencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals.
3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.NOTE:There is no tire pressure monitoring sensor in
the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire, in place of a road tire, that has a
pressure below the low-pressure warning
limit, upon the next ignition switch cycle, a
chime will sound, a “LOW TIRE PRESSURE”
message will be displayed in the instrument
cluster for a minimum of five seconds, an
Inflate to XXX
message will be displayed and
the Tire Pressure Monitoring Telltale Light will
turn ON. After driving the vehicle for up to 20
minutes above 15 mph (24 km/h), the Tire
Pressure Monitoring Telltale Light will flash on
and off for 75 seconds and then remain on
solid. In addition, a “SERVICE TPM SYSTEM”
message will be displayed for a minimum of
five seconds. For each subsequent ignition
switch cycle, a chime will sound, a “SERVICE
TPM SYSTEM” message will be displayed for
a minimum of five seconds, and the Tire Pres-
sure Monitoring Telltale Light will flash on and
off for 75 seconds and then remain on solid. Once you repair or replace the original road
tire, and reinstall it on the vehicle in place of
the spare tire, the TPMS will update automati-
cally and the Tire Pressure Monitoring Telltale
Light will turn OFF, as long as no tire pressure
is below the low-pressure warning limit in any
of the four active road tires. The vehicle may
need to be driven for up to 20 minutes above
15 mph (24 km/h) in order for the TPMS to
receive this information.
Premium System – If EquippedThe Tire Pressure Monitor System (TPMS)
uses wireless technology with wheel rim-
mounted electronic sensors to monitor tire pres-
sure levels. Sensors, mounted to each wheel as
part of the valve stem, transmit tire pressure
readings to the Receiver Module.
NOTE:
It is particularly important, for you to regu-
larly check the tire pressure in all of your
tires and to maintain the proper pressure.
269

The Tire Pressure Monitor System (TPMS) con-
sists of the following components:
•Receiver Module
• Four Tire Pressure Monitoring Sensors
•
Various Tire Pressure Monitoring System Mes-
sages, which display in the Electronic Vehicle
Information Center (EVIC), and a graphic dis-
playing tire pressures
• Tire Pressure Monitoring Telltale Light
Tire Pressure Monitoring Low Pressure
Warnings
The Tire Pressure Monitoring Telltale
Light will illuminate in the instrument
cluster, and an audible chime will be
activated, when one or more of the four
active road tire pressures are low. In addition, the
EVIC will display a “LOW TIRE PRESSURE”
message for a minimum of five seconds, an
"Inflate to XXX" message and a graphic display of
the pressure value(s) with the low tire(s) “flash- ing.” Refer to “Electronic Vehicle Information Cen-
ter (EVIC)” in “Understanding Your Instrument
Panel” for further information.
NOTE:
Your system can be set to display pressure
units in PSI, kPa, or BAR.
Should a low tire condition occur on any of the
four active road tire(s), you should stop as soon
as possible, and inflate the low tire(s) that is
“flashing” on the graphic display to the vehicle’s
recommended cold tire pressure displayed inthe
"Inflate to XXX" message. The system will
automatically update, the graphic display of the
pressure value(s) will stop “flashing,” and the
Tire Pressure Monitoring Telltale Light will extin-
guish once the updated tire pressure(s) have
been received. The vehicle may need to be
driven for up to 20 minutes above 15 mph
(24 km/h) to receive this information.
SERVICE TPM SYSTEM Warning
The Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds, and remain on
solid when a system fault is detected. The
system fault will also sound a chime. The EVIC
will display a “SERVICE TPM SYSTEM” mes-
sage for a minimum of five seconds. This mes-
sage is then followed by a graphic display, with
“- -“ in place of the pressure value(s), indicating
which Tire Pressure Monitoring Sensor(s) is not
being received.
NOTE:
Your system can be set to display pressure
units in PSI or kPa.
270

If the ignition switch is cycled, this sequence will
repeat, providing the system fault still exists. If
the system fault no longer exists, the Tire Pres-
sure Monitoring Telltale Light will no longer
flash, the"SERVICE TPM SYSTEM" message
will not be present, and a pressure value will be
displayed instead of dashes. A system fault can
occur by any of the following:
1. Jamming due to electronic devices or driving
next to facilities emitting the same Radio Fre-
quencies as the TPM sensors.
2. Installing some form of aftermarket window
tinting that affects radio wave signals. 3. Lots of snow or ice around the wheels or
wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM
sensors.
The EVIC will also display a
"SERVICE TPM
SYSTEM" message for a minimum of five sec-
onds when a system fault is detected possibly
related to an incorrect sensor location fault. In
this case, the "SERVICE TPM SYSTEM" mes-
sage is then followed by a graphic display, with
pressure values still shown. This indicates the
pressure values are still being received from the
TPM Sensors but they may not be located in the
correct vehicle position. However, the system
still needs to be serviced as long as the "SER-
VICE TPM SYSTEM" message exists.
NOTE:
There is no tire pressure monitoring sensor
in the spare tire. The TPMS will not be able to
monitor the tire pressure. If you install the
spare tire in place of a road tire that has a
pressure below the low-pressure warning limit, upon the next ignition switch cycle, the
Tire Pressure Monitoring Telltale Light will
remain ON, a chime will sound, and the EVIC
will still display a “flashing” pressure value
in the graphic display and an
Inflate to
XXX kPa message will be displayed. After
driving the vehicle for up to 20 minutes
above 15 mph (24 km/h), the Tire Pressure
Monitoring Telltale Light will flash on and off
for 75 seconds and then remain on solid. In
addition, the EVIC will display a “SERVICE
TPM SYSTEM message for five seconds
and then display dashes (- -) in place of the
pressure value. For each subsequent igni-
tion switch cycle, a chime will sound, the
Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds and then
remain on solid, and the EVIC will display a
SERVICE TPM SYSTEM message for five
seconds and then display dashes (- -) in
place of the pressure value. Once you repair
or replace the original road tire, and reinstall
it on the vehicle in place of the spare tire, the
TPMS will update automatically.
271

In addition, the Tire Pressure Monitoring Telltale
Light will turn OFF and the graphic in the EVIC
will display a new pressure value instead of
dashes (- -), as long as no tire pressure is below
the low-pressure warning limit in any of the four
active road tires. The vehicle may need to be
driven for up to 20 minutes above 15 mph
(24 km/h) in order for the TPMS to receive this
information.
TPMS DeactivationThe TPMS can be deactivated if replacing all
four wheel and tire assemblies (road tires) with
wheel and tire assemblies that do not have
TPMS Sensors, such as when installing winter
wheel and tire assemblies on your vehicle To
deactivate the TPMS, first, replace all four
wheel and tire assemblies (road tires) with tires
not equipped with Tire Pressure Monitoring
(TPM) Sensors. Then, drive the vehicle for
20 minutes above 24 km/h (15 mph). The TPMS
will chime, the"TPM Telltale Light" will flash on
and off for 75 seconds and then remain on and the Electronic Vehicle Information Center
(EVIC) will display the “SERVICE TPM SYS-
TEM” message and then display dashes (--) in
place of the pressure values. Beginning with the
next ignition switch cycle, the TPMS will no
longer chime or display the “SERVICE TPM
SYSTEM” message in the EVIC but dashes (--)
will remain in place of the pressure values.
To reactivate the TPMS, replace all four wheel
and tire assemblies (road tires) with tires
equipped with TPM sensors. Then, drive the
vehicle for up to 20 minutes above 24 km/h
(15 mph). The TPMS will chime, the
"TPM
Telltale Light" will flash on and off for 75 sec-
onds and then turn off, and the Electronic
Vehicle Information Center (EVIC) will display
the “SERVICE TPM SYSTEM” message. The
EVIC will also display pressure values in place
of the dashes. On the next ignition switch cycle
the "SERVICE TPM SYSTEM" message will no
longer be displayed as long as no system fault
exists.
General InformationTransmitter and receivers operate on a carrier
frequency of 433.92 MHz as required by EEC
regulations. These devices must be certified to
conform to specific regulations in each indi-
vidual country. Two sets of regulations are in-
volved: ETS (European Telecommunication
Standard) 300–220, which most countries use,
and German BZT federal regulation 225Z125,
which is based on ETC 300–220 but has addi-
tional unique requirements. Other defined re-
quirements are noted in ANNEX VI of COMMIS-
SION DIRECTIVE 95/56/EC. Operation is
subject to the following conditions:
•
This device may not cause harmful interfer-
ence.
• This device must accept any interference
received, including interference that may
cause undesired operation.
272

WARNING!(Continued)
•Vehicles with trailers should not be parked
on a grade. When parking, apply the park-
ing brake on the tow vehicle. Put the tow
vehicle transmission in PARK. For four-
wheel drive vehicles, make sure the trans-
fer case is not in NEUTRAL. Always, block
or "chock" the trailer wheels.
• GCWR must not be exceeded.
• Total weight must be distributed be-
tween the tow vehicle and the trailer
such that the following four ratings are
not exceeded:
1. GVWR
2. GTW
3. GAWR
4. Trailer tongue weight rating for the trailer hitch utilized . Towing Requirements – Tires
•
Proper tire inflation pressures are essential
to the safe and satisfactory operation of your
vehicle. Refer to “Tires – General Informa-
tion” in “Starting and Operating” for proper
tire inflation procedures.
• Check the trailer tires for proper tire inflation
pressures before trailer usage.
• Check for signs of tire wear or visible tire
damage before towing a trailer. Refer to
“Tires – General Information” in “Starting and
Operating” for proper inspection procedure.
• When replacing tires, refer to “Tires – Gen-
eral Information” in “Starting and Operating”
for proper tire replacement procedures. Re-
placing tires with a higher load carrying ca-
pacity will not increase the vehicle’s GVWR
and GAWR limits.
Towing Requirements – Trailer Brakes
• Do not interconnect the hydraulic brake sys-
tem or vacuum system of your vehicle with
that of the trailer. This could cause inad-
equate braking and possible personal injury. •
An electronically-actuated trailer brake con-
troller is required when towing a trailer with
electronically-actuated brakes. When towing
a trailer equipped with a hydraulic surge-
actuated brake system, an electronic brake
controller is not required.
• Trailer brakes are recommended for trailers
over 1,000 lbs (454 kg), and required for
trailers in excess of 1,654 lbs (750 kg).
WARNING!
•Do not connect trailer brakes to your vehi-
cle’s hydraulic brake lines. It can overload
your brake system and cause it to fail. You
might not have brakes when you need
them and could have an accident.
•
Towing any trailer will increase your stopping
distance. When towing, you should allow for
additional space between your vehicle and
the vehicle in front of you. Failure to do so
could result in an accident.
283

NOTE:
Intentional tampering with emissions con-
trol systems can result in civil penalties
being assessed against you.
In unusual situations involving grossly malfunc-
tioning engine operation, a scorching odor may
suggest severe and abnormal catalyst over-
heating. If this occurs, stop the vehicle, turn off
the engine and allow it to cool. Service, includ-
ing a tune-up to manufacturer’s specifications,
should be obtained immediately.
To minimize the possibility of catalytic converter
damage:
•Do not shut off the engine or interrupt the
ignition, when the transmission is in gear and
the vehicle is in motion.
• Do not try to start the engine by pushing or
towing the vehicle.
• Do not idle the engine with any spark plug
wires disconnected or removed, such as
when diagnostic testing, or for prolonged
periods during very rough idle or malfunction-
ing operating conditions.Cooling System
WARNING!
You or others can be badly burned by hot
engine coolant (antifreeze) or steam from
your radiator. If you see or hear steam com-
ing from under the hood, do not open the
hood until the radiator has had time to cool.
Never try to open a cooling system pressure
cap when the radiator or coolant bottle is hot.
Engine Coolant Checks
Check the engine coolant (antifreeze) protec-
tion every 12 months (before the onset of
freezing weather, where applicable). If the en-
gine coolant (antifreeze) is dirty, the system
should be drained, flushed, and refilled with
fresh OAT coolant (conforming to MS-12106) by
an authorized dealer. Check the front of the A/C
condenser for any accumulation of bugs,
leaves, etc. If dirty, clean by gently spraying
water from a garden hose vertically down the
face of the condenser. Check the engine cooling system hoses for
brittle rubber, cracking, tears, cuts, and tight-
ness of the connection at the coolant recovery
bottle and radiator. Inspect the entire system for
leaks.
With the engine at normal operating temperature
(but not running), check the cooling system pres-
sure cap for proper vacuum sealing by draining a
small amount of engine coolant (antifreeze) from
the radiator drain cock. If the cap is sealing
properly, the engine coolant (antifreeze) will begin
to drain from the coolant recovery bottle. DO NOT
REMOVE THE COOLANT PRESSURE CAP
WHEN THE COOLING SYSTEM IS HOT.
Cooling System – Drain, Flush, And Refill
If the engine coolant (antifreeze) is dirty or
contains visible sediment, clean and flush with
OAT coolant (antifreeze) that meets the require-
ments of Chrysler Material Standard MS-12106.
Refer to the “Maintenance Schedule” for the
proper maintenance intervals.
321

Cav-ity Car-
tridge Fuse Mini
Fuse Description
M19
25
Amp
Natu- ralAutomatic
Shutdown 1 and 2
M20 15
Amp Blue Instrument
Cluster
M21 20
Amp
Yellow Automatic
Shutdown 3
M22 10
Amp Red Horns (Low/
High) – Right
M23 10
Amp Red Horns (Low/
High) – Left
M24 25
Amp
Natu- ral Rear Wiper
Cav-
ity Car-
tridge Fuse Mini
Fuse Description
M25 20
Amp
Yellow Fuel Pump
Motor Output/ Diesel Lift
Pump (Export Only)
M26 10
Amp Red Driver Door
Switch Bank
M27 10
Amp Red Ignition Switch/
Wireless Con- trol Module/
Keyless Entry Module
M28 15
Amp Blue Powertrain
Controller/
Transmission Controller
M29 10
Amp Red Tire Pressure
Monitor – IfEquippedCav- ity Car-
tridge Fuse Mini
Fuse Description
M30 15
Amp Blue J1962 Diag
Connector
M31 20
Amp
Yellow Backup Lamps
M32 10
Amp Red Occupant
Restraint
Controller
M33 10
Amp Red Powertrain
Controller/
Transmission Controller
M34 10
Amp Red
Park Assist
Module/Climate Control System Module/Infra
Red Sensor/ CompassModule
334