
CAUTION!
•Damage to the fuel system or emission
control system could result from using an
improper fuel cap (gas cap). A poorly fitting
cap could let impurities into the fuel sys-
tem. Also, a poorly fitting aftermarket cap
can cause the “Malfunction Indicator Light
(MIL)” to illuminate, due to fuel vapors
escaping from the system.
• A poorly fitting gas cap may cause the MIL
to turn on.
• To avoid fuel spillage and overfilling, do not
“top off” the fuel tank after filling.
WARNING!
•Never have any smoking materials lit in or
near the vehicle when the gas cap is
removed or the tank is being filled.
(Continued)
WARNING!(Continued)
•Never add fuel when the engine is running.
This is in violation of most state and fed-
eral fire regulations and may cause the
malfunction indicator light to turn on.
•
A fire may result if gasoline is pumped into a
portable container that is inside of a vehicle.
You could be burned. Always place gas
containers on the ground while filling.
NOTE:
• When the fuel nozzle “clicks” or shuts off,
the fuel tank is full.
•
Tighten the gas cap about one-quarter turn
until you hear one click. This is an indica-
tion that the cap is properly tightened.
•If the gas cap is not tighten properly, the MIL
will come on. Be sure the gas cap is tight-
ened every time the vehicle is refueled.
Emergency Fuel Filler Door Release
If you are unable to open the fuel filler door, use
the fuel filler door emergency release.
1. Open the liftgate.
2. Push down on the inboard edge of the left
storage bin, this will pop up the outboard edge.
3. Grab popped up outboard edge with other
hand to disengage snaps.
4. Remove the storage bin.
5. Pull the release cable.
Release Cable
277

Loose Fuel Filler Cap Message
If the vehicle diagnostic system de-
termines that the fuel filler cap is
loose, improperly installed, or dam-
aged, a loose gascap indicator will
display in the EVIC telltale display
area. Refer to “Electronic Vehicle
Information Center (EVIC)” in “Understanding
Your Instrument Panel” for further information.
Tighten the fuel filler cap properly and press the
SELECT button to turn off the message. If the
problem continues, the message will appear the
next time the vehicle is started.
TRAILER TOWING
In this section you will find safety tips and infor-
mation on limits to the type of towing you can
reasonably do with your vehicle. Before towing a
trailer, carefully review this information to tow your
load as efficiently and safely as possible. To maintain warranty coverage, follow the require-
ments and recommendations in this manual con-
cerning vehicles used for trailer towing.
Common Towing DefinitionsThe following trailer towing related definitions
will assist you in understanding the following
information:
Gross Vehicle Weight Rating (GVWR)
The GVWR is the total allowable weight of your
vehicle. This includes driver, passengers, cargo
and tongue weight. The total load must be
limited so that you do not exceed the GVWR.
Refer to “Vehicle Loading/Vehicle Certification
Label” in “Starting and Operating” for further
information.
Gross Trailer Weight (GTW)
The GTW is the weight of the trailer plus the
weight of all cargo, consumables and equip-
ment (permanent or temporary) loaded in or on
the trailer in its
"loaded and ready for operation "
condition. The recommended way to measure
GTW is to put your fully loaded trailer on a
vehicle scale. The entire weight of the trailer
must be supported by the scale.
Gross Combination Weight Rating (GCWR)
The GCWR is the total permissible weight of
your vehicle and trailer when weighed in com-
bination.
NOTE:
The GCWR rating includes a 150 lbs (68 kg)
allowance for the presence of a driver.
Gross Axle Weight Rating (GAWR)
The GAWR is the maximum capacity of the front
and rear axles. Distribute the load over the front
and rear axles evenly. Make sure that you do
not exceed either front or rear GAWR.
278

7
MAINTAINING YOUR VEHICLE
•ENGINE COMPARTMENT — 3.6L ...................309
• ENGINE COMPARTMENT — 5.7L ...................310
• ENGINE COMPARTMENT — 3.0L DIESEL ..............311
• ONBOARD DIAGNOSTIC SYSTEM (OBD II) .............312
•Loose Fuel Filler Cap Message ...................312•REPLACEMENT PARTS .........................312
• MAINTENANCE PROCEDURES ....................312
•Engine Oil – Gasoline Engines ....................313
• Engine Oil – Diesel Engine ..................... .314
• Synthetic Engine Oils ........................ .315
• Materials Added To Engine Oil ....................315
• Disposing Of Used Engine Oil And Oil Filters ...........315
• Engine Oil Filter ........................... .315
• Engine Air Cleaner Filter ...................... .315
• Maintenance-Free Battery ...................... .316
• Air Conditioner Maintenance .................... .316
• Body Lubrication ........................... .318
• Windshield Wiper Blades ...................... .318
• Adding Washer Fluid ........................ .319
307

ONBOARD DIAGNOSTIC
SYSTEM (OBD II)
Your vehicle is equipped with a sophisticated
onboard diagnostic system called OBD II. This
system monitors the performance of the emis-
sions, engine, and automatic transmission con-
trol systems. When these systems are operat-
ing properly, your vehicle will provide excellent
performance and fuel economy, as well as
engine emissions well within current govern-
ment regulations.
If any of these systems require service, the
OBD II system will turn on the “Malfunction
Indicator Light (MIL).” It will also store diagnos-
tic codes and other information to assist your
service technician in making repairs. Although
your vehicle will usually be drivable and not
need towing, see your authorized dealer for
service as soon as possible.
CAUTION!
•
Prolonged driving with the MIL on could
cause further damage to the emission con-
trol system. It could also affect fuel economy
and drivability. The vehicle must be serviced
before any emissions tests can be per-
formed.
•If the MIL is flashing, while the engine is
running, severe catalytic converter dam-
age and power loss will soon occur. Imme-
diate service is required.
Loose Fuel Filler Cap Message
If the vehicle diagnostic system de-
termines that the fuel filler cap is
loose, improperly installed, or dam-
aged, a loose gascap indicator will
display in the EVIC telltale display
area. Refer to “Electronic Vehicle
Information Center (EVIC) in “Understanding
Your Instrument Panel” for further information.
Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the
problem continues, the message will appear the
next time the vehicle is started.
A loose, improperly installed, or damaged fuel
filler cap may also turn on the Malfunction
Indicator Light (MIL).
REPLACEMENT PARTS
Use of genuine MOPAR® parts for normal/
scheduled maintenance and repairs is highly
recommended to ensure the designed perfor-
mance. Damage or failures caused by the use
of non-MOPAR® parts for maintenance and
repairs will not be covered by the manufactur-
er’s warranty.
MAINTENANCE PROCEDURES
The pages that follow contain the
required
maintenance services determined by the engi-
neers who designed your vehicle.
Besides those maintenance items specified in
the fixed maintenance schedule, there are other
components which may require servicing or
replacement in the future.
312

CAUTION!
Do not use chemical flushes in your engine
oil as the chemicals can damage your en-
gine. Such damage is not covered by the
New Vehicle Limited Warranty.
Engine Oil Selection – ACEA Categories
For countries that use the ACEA European Oil
Categories for Service Fill Oils, we recommend
you use 5W-20 engine oils that meet the re-
quirements of ACEA C3.
Engine Oil Viscosity – 3.6L Engine
SAE 5W-20 engine oil is recommended for all
operating temperatures. This engine oil im-
proves low temperature starting and vehicle fuel
economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your engine. For
information on engine oil filler cap location, refer
to the “Engine Compartment” illustration in this
section. NOTE:
SAE 5W-30 engine oil approved to Fiat
9.55535-S1 or Fiat 9.55535-S3 may be used
when SAE 5W-20 engine oil meeting MS-
6395 is not available.
Engine Oil Viscosity – 5.7L Engine
SAE 5W-20 engine oil is recommended for all
operating temperatures. This engine oil im-
proves low temperature starting and vehicle fuel
economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your engine. For
information on engine oil filler cap location, refer
to the “Engine Compartment” illustration in this
section.
NOTE:
SAE 5W-30 engine oil approved to Fiat
9.55535-S1 or Fiat 9.55535-S3 may be used
when SAE 5W-20 engine oil meeting MS-
6395 is not available.Engine Oil – Diesel Engine
Engine Oil Selection
For best performance and maximum protection
under all types of operating conditions, the
manufacturer recommends you use SAE 5W-30
Synthetic Low Ash Engine Oil meeting the re-
quirements of Chrysler Material Standard
MS-11106 and approved ACEA C3.
Engine Oil Viscosity
CAUTION!
Your vehicle is equipped with an advanced
technology Diesel Engine and an emission
device designed to limit Diesel Particulate
Emissions from being released into the at-
mosphere. The durability of your engine and
life expectancy of this diesel particulate filter
emission device is highly dependent on the
use of the correct engine oil.
314

SAE 5W-30 Synthetic Low Ash Engine Oil is
recommended for all operating temperatures.
This engine oil improves low temperature start-
ing and vehicle fuel economy.
The engine oil filler cap also shows the recom-
mended engine oil viscosity for your engine. For
information on engine oil filler cap location, refer
to “Engine Compartment” in “Maintaining Your
Vehicle” for further information.
Synthetic Engine OilsYou may use synthetic engine oils provided the
recommended oil quality requirements are met,
and the recommended maintenance intervals
for oil and filter changes are followed.
Materials Added To Engine OilThe manufacturer strongly recommends
against the addition of any additives (other than
leak detection dyes) to the engine oil. Engine oil
is an engineered product and its performance
may be impaired by supplemental additives.
Disposing Of Used Engine Oil And
Oil Filters
Care should be taken in disposing of used
engine oil and oil filters from your vehicle. Used
oil and oil filters, indiscriminately discarded, can
present a problem to the environment. Contact
your authorized dealer, service station or gov-
ernmental agency for advice on how and where
used oil and oil filters can be safely discarded in
your area.
Engine Oil FilterThe engine oil filter should be replaced with a
new filter at every engine oil change.
Engine Oil Filter Selection
This manufacturer’s engines have a full-flow
type disposable oil filter. Use a filter of this type
for replacement. The quality of replacement
filters varies considerably. Only high quality
filters should be used to assure most efficient
service. MOPAR® engine oil filters are high
quality oil filters and are recommended.
Engine Air Cleaner FilterRefer to the “Maintenance Schedule” for the
proper maintenance intervals.
WARNING!
The air induction system (air cleaner, hoses,
etc.) can provide a measure of protection in
the case of engine backfire. Do not remove
the air induction system (air cleaner, hoses,
etc.) unless such removal is necessary for
repair or maintenance. Make sure that no
one is near the engine compartment before
starting the vehicle with the air induction
system (air cleaner, hoses, etc.) removed.
Failure to do so can result in serious per-
sonal injury.
Engine Air Cleaner Filter Selection
The quality of replacement engine air cleaner
filters varies considerably. Only high quality
filters should be used to assure most efficient
service. MOPAR® engine air cleaner filters are
a high quality filter and are recommended.
315

FLUID CAPACITIES
U.S.Metric
Fuel (Approximate)
All Engines 24.6 Gallons93 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-20, API Certified) 6 Quarts5.6 Liters
5.7L Engine (SAE 5W-20, API Certified) 7 Quarts6.6 Liters
3.0L Diesel Engine (SAE 5W-30 Synthetic, API Certified Low Ash) 9 Quarts8.4 Liters
Cooling System *
3.6L Engine (MOPAR® Engine Coolant/Antifreeze 10-Year/150,000 Mile Formula) 10.4 Quarts9.9 Liters
5.7 Liter Engine (MOPAR® Engine Coolant/Antifreeze 10-Year/150,000 Mile
Formula) – Without Trailer Tow Package 15.4 Quarts
14.6 Liters
5.7 Liter Engine (MOPAR® Engine Coolant/Antifreeze 10-Year/150,000 Mile
Formula) – With Trailer Tow Package 16 Quarts
15.2 Liters
3.0L Diesel Engine (MOPAR® Engine Coolant/Antifreeze 10-Year/150,000 Mile
Formula) 13.9 Quarts
13.2 Liters
* Includes heater and coolant recovery bottle filled to MAX level.
340

Adaptive Cruise Control (ACC)(Cruise Control) ..............119
Adding Engine Coolant (Antifreeze) . . . .322
Adding Fuel ................. .276
Additives, Fuel ................274
Airbag ...................41, 46
Airbag Deployment ..............47
Airbag Light ...........45, 49, 60, 162
Airbag Maintenance ..............48
Airbag, Side ..............43, 44, 46
Airbag, Window (Side Curtain) . . . .43, 44, 46
Air Cleaner, Engine (Engine Air Cleaner Filter) ...............315
Air Conditioner Maintenance ........316
Air Conditioning Filter ............317
Air Conditioning Refrigerant .........317
Air Conditioning System ...........209
Air Pressure, Tires ..............260
Air Suspension ................241
Alarm (Security Alarm) ............167
Alarm System (Security Alarm) ........16
Alterations/Modifications, Vehicle .......8
Antifreeze (Engine Coolant) ......322, 340
Disposal .................323
Anti-Lock Brake System (ABS) .......252
Anti-Lock Warning Light ...........166
Anti-Theft Security Alarm (Theft Alarm) . . .16 Anti-Theft System
..............167
Appearance Care ...............328
Assist, Hill Start ................256
Auto Down Power Windows .........26
Automatic Dimming Mirror ..........70
Automatic Door Locks .............22
Automatic Headlights .............107
Automatic Oil Change Indicator .......177
Automatic Temperature Control (ATC) . . .209
Automatic Transmission .....226, 231, 328
Adding Fluid ...............328
Fluid and Filter Changes ........328
Fluid Change ..............328
Fluid Level Check .........326, 327
Fluid T
ype................326
Special Additives ............327
Autostick ................ .230, 235
Auxiliary Electrical Outlet (Power Outlet) . .146
Auxiliary Power Outlet ............146
Battery .................... .316
Keyless Transmitter
Replacement (RKE) ...........20
Belts, Seat ................ .33, 60
Body Mechanism Lubrication ........318
Brake Assist System .............252
Brake Control System, Electronic ......252Brake Fluid
................. .324
Brake System .................324
Anti-Lock (ABS) .............252
Fluid Check ...............324
Master Cylinder .............324
Parking ................. .250
Warning Light ..............165
Brake/Transmission Interlock ........226
Bulb Replacement ..............336
Bulbs, Light ...................61
Calibration, Compass ............184
Camera, Rear .................139
Capacities, Fluid ...............340
Caps, Filler Fuel ....................276
Power Steering .............250
Radiator (Coolant Pressure) ......323
Carbon Monoxide Warning ..........60
Cargo Area Cover ..............152
Cargo Area Features .............151
Cargo Compartment .............151
Light ...................151
Cargo Light ................. .151
Cargo Tie-Downs ...............153
Car Washes ................. .329
Cellular Phone ............. .72,
209
394