2013 FIAT FREEMONT tow

filter cover to the HVAC housing and remove the
cover. (fig. 178)5. Remove the A/C air filter by pulling it straight out of
the housing.
6. Install the A/C air filter with the arrow on the filter pointing toward the floor. When installing the filter
cover, make sure the retaining tabs fully engage the
cover.
The A/C air filter is identified with an
arrow to indicate airflow direction
through the filter. Failure to install the
filter properly will result in the need to replace it
more often.
7. Reinstall the glove box door. Make sure that the hinges are seated fully as you raise the door. Other-
wise, the door latch will not align properly.
BODY LUBRICATION
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
tailgate, sliding doors and hood hinges, should be
lubricated periodically with a lithium based grease to
assure quiet, easy operation and to protect against rust
and wear. Prior to the application of any lubricant, the
parts concerned should be wiped clean to remove dust
and grit; after lubricating excess oil and grease should
be removed. Particular attention should also be given
to hood latching components to ensure proper func-
tion. When performing other underhood services, the
(fig. 177) Glove Box Removal(fig. 178)
A/C Air Filter Replacement
299
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
C
ARETECHNICAL
SPECIFICATIONSCONTENTS

5. Lower the wiper blade and snap the pivot cap intoplace.
ADDING WASHER FLUID
The windshield washer and the rear window washer
share the same fluid reservoir. The fluid reservoir is
located in the engine compartment. Be sure to check
the fluid level in the reservoir at regular intervals. Fill
the reservoir with windshield washer solvent (not
radiator antifreeze) and operate the system for a few
seconds to flush out the residual water. When refilling the washer fluid reservoir, apply some
washer fluid to a cloth or towel and wipe the wiper
blades clean. This will help blade performance.
To prevent freeze-up of your windshield washer system
in cold weather, select a solution or mixture that meets
or exceeds the temperature range of your climate. This
rating information can be found on most washer fluid
containers.(fig. 179)1 — Wiper Arm
2 — Pivot Cap
(fig. 180)1 — Wiper Blade
2 — Blade Pivot Pin
3 — Wiper Arm
4 — Wiper Blade Holder
301
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

WARNING!
Exhaust gases can injure or kill. They
c
ontain carbon monoxide (CO), which is
colorless and odorless. Breathing it can make you
unconscious and can eventually poison you. To
avoid breathing CO, refer to “Safety Tips/Exhaust
Gas” in “Safety” for further information.
NOTE: Intentional tampering with emissions control
systems can result in civil penalties being assessed
against you.
WARNING!
A hot exhaust system can start a fire if
y
ou park over materials that can burn.
Such materials might be grass or leaves coming
into contact with your exhaust system. Do not
park or operate your vehicle in areas where your
exhaust system can contact anything that can
burn.
In unusual situations involving grossly malfunctioning
engine operation, a scorching odor may indicate severe
and abnormal catalyst overheating. If this occurs, safely
bring the vehicle to a complete stop, shut the engine
OFF, and allow the vehicle to cool. Thereafter, obtain
service, including a tune-up to manufacturer’s specifi-
cations immediately. To minimize the possibility of catalyst damage:
 Do not shut OFF the engine or interrupt the ignition
when the transmission is in gear and the vehicle is in
motion.
 Do not try to start the engine by pushing or towing the vehicle.
 Do not idle the engine with any ignition coil connec- tors disconnected for prolonged periods.
COOLING SYSTEM
WARNING!
 Wh
en working near the radiator cool-
ing fan, disconnect the fan motor lead or
turn the ignition switch to the LOCK position.The
fan is temperature controlled and can start at
any time the ignition switch is in the ON position.
 You or others can be badly burned by hot
engine coolant (antifreeze) or steam from your
radiator. If you see or hear steam coming from
under the hood, do not open the hood until the
radiator has had time to cool. Never try to open a
cooling system pressure cap when the radiator is
hot .
303
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

 If your vehicle is damaged due to an accident orsimilar cause, which destroys the paint and protec-
tive coating, have your vehicle repaired as soon as
possible. The cost of such repairs is considered the
responsibility of the owner.
 If you carry special cargo such as chemicals, fertiliz- ers, de-icer salt, etc., be sure that such materials are
well packaged and sealed.
 If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel.
 Use Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch
up paint to match the color of your vehicle.
Wheel And Wheel Trim Care
All wheels and wheel trim, especially aluminum and
chrome-plated wheels should be cleaned regularly with
a mild soap and water to prevent corrosion. To remove
heavy soil and/or excessive brake dust, use a nonabra-
sive, non-acidic cleaner. Do not use scouring pads, steel
wool, a bristle brush, or metal polishes. Do not use
oven cleaner. Avoid automatic car washes that use
acidic solutions or harsh brushes that may damage the
wheels’ protective finish. Stain Repel Fabric Cleaning Procedure (for
versions/markets, where provided)
Stain Repel seats may be cleaned in the following
manner:
 Remove as much of the stain as possible by blotting
with a clean, dry towel.
 Blot any remaining stain with a clean, damp towel.
 For tough stains, apply a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh,
damp towel to remove soap residue.
 For grease stains, apply a Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the
stain. Use a fresh, damp towel to remove soap
residue.
 Do not use any harsh solvents or any other form of protectants on Stain Repel products.
Interior Care
Instrument Panel Cover
The instrument panel cover has a low glare surface,
which minimizes reflections in the windshield. Do not
use protectants or other products, which may cause
undesirable reflections. Use soap and warm water to
restore the low glare surface.
312
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
C
ARETECHNICAL
SPECIFICATIONSCONTENTS

Cleaning Interior Trim
Interior trim should be cleaned starting with a damp
cloth. Do not use harsh cleaners.
Cleaning Leather Upholstery
Your leather upholstery can be best preserved by
regular cleaning with a damp soft cloth. Small particles
of dirt can act as an abrasive and damage the leather
upholstery and should be removed promptly with a
damp cloth. Stubborn soils can be removed easily with
a soft cloth. Care should be taken to avoid soaking your
leather upholstery with any liquid. Please do not use
polishes, oils, cleaning fluids, solvents, detergents, or
ammonia-based cleaners to clean your leather uphol-
stery. Application of a leather conditioner is not re-
quired to maintain the original condition.
WARNING!
Do not use volatile solvents for cleaning
pur
poses. Many are potentially flam-
mable, and if used in closed areas they may cause
respiratory harm.
Cleaning Headlights
Your vehicle has plastic headlights that are lighter and
less susceptible to stone breakage than glass headlights.
Plastic is not as scratch resistant as glass and therefore
different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution
followed by rinsing.
Do not use abrasive cleaning components, solvents,
steel wool or other aggressive material to clean the
lenses.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis
with any commercial household-type glass cleaner.
Never use an abrasive type cleaner. Use caution when
cleaning the inside rear window equipped with an
electric defroster. Do not use scrapers or other sharp
instruments that may scratch the elements.
When cleaning the rear view mirror, spray cleaner on
the towel or rag that you are using. Do not spray
cleaner directly on the mirror.
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
1. Clean with a wet soft rag. A mild soap solution may
be used, but do not use high alcohol content or
abrasive cleaners. If soap is used, wipe clean with a
clean damp rag.
2. Dry with a soft cloth.
313
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
C
ARETECHNICAL
SPECIFICATIONSCONTENTS

Seat Belt Maintenance
Do not bleach, dye or clean the belts with chemical
solvents or abrasive cleaners. This will weaken the
fabric. Sun damage can also weaken the fabric.
If the belts need cleaning, use a mild soap solution or
lukewarm water. Do not remove the belts from the car
to wash them. Dry with a soft cloth.
Replace the belts if they appear frayed or worn or if the
buckles do not work properly.
CLEANING THE CUP HOLDERS
Clean with a damp cloth or towel using a mild deter-
gent.VEHICLE STORAGE
If you will not be using your vehicle for more than 21
days, you may want to take steps to preserve your
battery.
 Disengage the mini-fuse in the Power Distribution
Center labeled IOD (Ignition Off-Draw).
 Or disconnect the negative cable from the battery.
 Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run
the air conditioning system at idle for about five
minutes in the fresh air and high blower setting. This
will ensure adequate system lubrication to minimize
the possibility of compressor damage when the sys-
tem is started again.
314
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
C
ARETECHNICAL
SPECIFICATIONSCONTENTS

You may find fuels containing 3% or more methanol
along with other alcohols called cosolvents. Problems
that result from using methanol/gasoline or E-85 Etha-
nol blends are not the responsibility of the manufac-
turer. While MTBE is an oxygenate made from Metha-
nol, it does not have the negative effects of Methanol.
Do not use gasolines containing Metha-
nol or E-85 Ethanol. Use of these blends
may result in starting and driveability
problems and may damage critical fuel system
components.
Ethanol
The manufacturer recommends that your vehicle be
operated on fuel containing no more than 10% ethanol.
Purchasing your fuel from a reputable supplier may
reduce the risk of exceeding this 10% limit and/or of
receiving fuel with abnormal properties. It should also
be noted that an increase in fuel consumption should
be expected when using ethanol-blended fuels, due to
the lower energy content of ethanol. Problems that
result from using methanol/gasoline or E-85 ethanol
blends are not the responsibility of the manufacturer.
While MTBE is an oxygenate made from Methanol, it
does not have the negative effects of Methanol.
Use of fuel with Ethanol content higher
than 10% may result in engine malfunc-
tion, starting and operating difficulties,
and materials degradation.These adverse effects
could result in permanent damage to your vehicle.
Clean Air Gasoline
Many gasolines are now being blended to contribute to
cleaner air, especially in those areas where air pollution
levels are high. These new blends provide a cleaner
burning fuel and some are referred to as “reformulated
gasoline.”
The manufacturer supports these efforts toward
cleaner air. You can help by using these blends as they
become available.
MMT In Gasoline
MMT is a manganese containing metallic additive that is
blended into some gasoline to increase octane. Gaso-
line blended with MMT provides no performance ad-
vantage beyond gasoline of the same octane number
without MMT. Gasoline blended with MMT reduces
spark plug life and reduces emission system perfor-
mance in some vehicles. The manufacturer recom-
mends that gasoline without MMT be used in your
vehicle. The MMT content of gasoline may not be
indicated on the gasoline pump; therefore, you should
325
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Daytime Brightness, Interior Lights . . . . . . . . . . . . . . .78
Defroster, Rear Window . . . . . . . . . . . . . . . . . . . . . .84
Defroster, Windshield . . . . . . . . . . . . . . . . . . . .67, 200
Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . . .80
Diagnostic System, Onboard . . . . . . . . . . . . . . . . . .126
Diesel Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .327, 328
Diesel Fuel Requirements . . . . . . . . . . . . . . . . . . . .327
Dimmer Switch, Headlight . . . . . . . . . . . . . . . . . . . . .77
DipsticksAutomatic Transmission . . . . . . . . . . . . . . . . . . .309
Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . .294, 295
Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .128
Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . . .280
Disposal Antifreeze (Engine Coolant) . . . . . . . . . . . . . . . .306
Door Locks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . . .102
Downshifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211
Driving Through Flowing, Rising, or Shallow Standing Water .224
Driving to Achieve Maximum Fuel Economy . . . . . . . . .26
Electrical Outlet, Auxiliary (Power Outlet) . . . . . . . . . .94
Electrical Power Outlets . . . . . . . . . . . . . . . . . . . . . .94
Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . . . .61
Electronic Brake Control System . . . . . . . . . . . . . . .120 Anti-Lock Brake System . . . . . . . . . . . . . . . . . . .119
Brake Assist System . . . . . . . . . . . . . . . . . . . . . .122
Electronic Roll Mitigation . . . . . . . . . . . . . . . . . .122
Electronic Stability Program . . . . . . . . . . . . . . . .123
Traction Control System . . . . . . . . . . . . . . . . . .122
Electronic Roll Mitigation (ERM) . . . . . . . . . . . . . . . .122
Electronic Speed Control (Cruise Control) . . . . . . . . .85 Electronic Stability Program (ESP) . . . . . . . . . . . . . . .123
Electronic Vehicle Information Center (EVIC). . . . .19, 141
Emergency, In Case of
Freeing Vehicle When Stuck . . . . . . . . . . . . . . . .276
Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . .89
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .245
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .280
Engine. . . . . . . . . . . . . . . . . . . . . . . . . . .202, 291, 293 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .296
Break-In Recommendations . . . . . . . . . . . . . . . . .202
Checking Oil Level . . . . . . . . . . . . . . . . . . .294, 295
Compartment . . . . . . . . . . . . . . . . . . . . . .291, 292
Compartment Identification . . . . . . . . . . . . . . . .292
Coolant (Antifreeze) . . . . . . . . . . . . . . . . . .304, 328
Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .303
Exhaust Gas Caution . . . . . . . . . . . . . . . . . .111, 199
Fails to Start . . . . . . . . . . . . . . . . . . . . . . . . . . .204
Flooded, Starting . . . . . . . . . . . . . . . . . . . . . . . .204
Fuel Requirements . . . . . . . . . . . . . . . . . . . . . . .324
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . .245
Oil . . . . . . . . . . . . . . . . . . . . . . . . . .294, 327, 328
Oil Change Interval . . . . . . . . . . . . . . . .25, 295, 296
Oil Filler Cap . . . . . . . . . . . . . . . . . . .291, 293, 296
Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . .327
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .202
Temperature Gauge . . . . . . . . . . . . . . . . . . . . . . .7
Engine Oil Viscosity . . . . . . . . . . . . . . . . . . . . .295, 296
Engine Oil Viscosity Chart . . . . . . . . . . . . . . . . . . . .295
Enhanced Accident Response Feature . . . . . . . . . . . .195
Entry System, Illuminated . . . . . . . . . . . . . . . . . . . . .79
Ethanol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .324
Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . .197
335
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS
AND
MESSAGES
IN AN
EMERGENCY
SERVICING
AND
CARETECHNICAL
SPECIFICATIONSCONTENTS