2013 Citroen C4 PICASSO RHD panel

159
4
Driving

Operation









Gear shift indicator

System which reduces fuel consumption by advising the driver to change up.
With an electronic gearbox, the system is only active in Manual mode.


The system adapts its gear change recommendation according to thedriving conditions (slope, load, ...) and the demands of the driver (power,acceleration, braking, ...).
The system never suggests:


- engaging first gear,

- engaging reverse gear,

- engaging a lower gear.
Example:
- You are in third gear.
- Yo u press the accelerator pedal.
- The s
ystem may suggest that you engage a
higher gear.
The in
formation appears in the instrumentpanel in the form of an arrow. On vehicles with manual gearbox, the arrowcan be accompanied by the recommended gear.
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one (or more) gear(s). You can
follow this instruction without engaging the
intermediate gears.
The gear engagement recommendations mustnot be considered compulsory. In fact, the configuration of the road, the amount of traffic
and safety remain determining factors whenchoosing the best gear. Therefore, the driver
remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated.

160
Driving














Stop & Start
Operation
Going into engine STOP mode
The "ECO"
warning lamp comes onin the instrument panel and the enginegoes into standby automatically:
-with a manual gearbox
, at speeds below
12 mph (20 km/h), when you place the gear lever in neutral, and you release the clutch pedal, - with an electronic gearbox,at speeds
below 5 mph (8 km/h), when you press the
brake pedal or place the gear selector lever in position N ,
- with an automatic gearbox,
with the
vehicle stationary, when you press the brake pedal or place the gear selector lever in position N.If your vehicle is fitted with the system, a timecounter calculates the sum of the periods in STOP mode during a journey. It resets itself to
zero every time the ignition is switched on with
the STA R T/STOP button.
Never refuel with the engine in STOPmode; you must switch off the ignition with the STA R T/STOP button.
For your comfor t, during parkingmanoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...


Special cases: STOP mode not
available
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded
6 mph(10 km/h) since the last engine start usingthe START/STOP button,

- the electric parking brake is applied or being applied,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demistin
g is active,

- some special conditions (battery charge, engine temperature, braking assistance,ambient temperature...) where the engine isneeded to assure control of a system.

In this case, the "ECO"
warning lampflashes for a few seconds then goesoff.This operation is per fectly normal.
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restar ts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.

162
Driving

The system is reactivated automaticallyevery time the engine is star ted by the driver.

Reactivation

Press this button again.


Operating fault

Have it checked by a CITROËN dealer or aqualified workshop.
In the event of a fault in STOP mode, the
vehicle may stall.
All of the instrument panel warning lamps come on.
Depending on version, an alert message may
also be displa
yed, asking you to place the gear
selector lever in position Nand put your foot on
the brake pedal.
It is then necessar
y to switch off the ignition
and star t the engine again using the "START/STOP" button.In th
e event of a fault with the system, this warning lamp comes
on continuously.
The system is active again; this is confirmed by the indicator lamp in thebutton going off and illumination of
this symbol.
The Stop & Start system makes use of advanced technology. For any work onthe system go to a qualified workshop with the skills and equipment required, which a CITROËN dealer is able toprovide.

Before doing anything under the bonnet,deactivate the Stop & Start system toavoid any risk of injury resulting fromautomatic operation of STA R T m o d e .


Maintenance

This system requires a 12 V battery with a special specification and technology (reference numbers available from CITROËN dealers).
Fitting a battery not listed by CITROËN introduces the risk of malfunction of
the system.
For charging, use a 12 V charger and do not
reverse the polarity.

163
4
Driving




Display of inter-vehicle time


Using a radar located at the front of the vehicle,
this system helps the driver maintain a safe distance between their vehicle and the one in
front, b
y displaying the inter-vehicle time in the instrument panel.
It is the time interval, expressed in seconds,
that separates two vehicles in line. The
recommended safe value is about 2 seconds:
refer to the legislation or highway code in force
in your country.

Activation / deactivation
)Press this button, the indicator lamp comes on.
The measurement is displayed for information only: the system takes no action on the vehicle. This system does not in anycircumstances replace the vigilance and responsibility of the driver who mustremain in control of their vehicle at all times. The system is not designed for urbanuse nor during more dynamic driving (bends, acceleration, harsh braking…)but rather when driving at stable speed.
The system is active in a speed range between 42 and 93 mph (70 and 15 0 km / h).Stationary vehicles and cer tain other road users (such as bicycles for example) are not detected. The system displays inter-vehicle timevalues of between 3 seconds and 0.5 of a second. Below 0.5 of a second, the value displayed is maintained at this level,even if the true inter-vehicle time is less.

Activation of the active cruise control automatically deactivates the system. The state o
f the system is memorised when the
ignition is switched off.
Activation of the system is done in the " Driving assistance" menu, with the ignition on.
This system is only available with the "DRIVING" display mode of the type 2instrument panel.

164
Driving
Once the system has been activated and the speed conditions are met, a symbol is displayed in the instrument panel.
Displays
SymbolAssociated messageComments
No vehicle detected b
y the radar.
A vehicle is detected but the inter-vehicle time is more than
3 seconds. No value is
displayed.
A vehicle is detected. The inter-vehicle time is
3 seconds or less. The minimum value
displayed is 0.5 seconds, even if the true inter-vehicle time is lower.

168
Driving

Steering mounted controls


The information is grouped together in the
instrument panel.
6
. Speed limiter on / pause indication.
7. Speed limiter mode selection indication. 8. Speed value setting.






Speed limiter
Once the programmed speed limit is reached, additional pressure on the accelerator pedal has no effect.


The speed limiter cannot, in any circumstances,replace the need to observe speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
System which prevents the vehicle fromexceeding the speed programmed by the driver.

The controls are
grouped together at the
steering wheel.
1.Speed limiter mode selection wheel.
2. Value decrease button. 3.
Value increase button.
4.Speed limiter on / pause button.
5.List of memorised speeds display button.

Displays in the instrument panel
The speed limiter is switched onmanually:
it requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is paused
by operation of the control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply release the accelerator pedal until the vehicle returns to the programmed speed limit.
The programmed speed remains in the memory when the ignition is switched off.

F
or more information on the list of memorisedspeeds, refer to the "Memorising speeds"
section.

171
4
Driving
Steering mounted controls
The information is grouped together in the instrument panel.
6. Cruise control pause / resume indication.
7.Cruise control mode selection indication. 8.Speed value setting.






Cruise control

System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.


The cruise control system cannot, in any circumstances, replace the need to obser ve speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
You are advised to keep your feet near the pedals at all times.
Th
e cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and engagement of:


- at least four th gear on a manual gearbox,

- second gear on an electronic or automatic gearbox, in manual driving mode,

- position A
on an electronic gearbox or D
on an automatic gearbox.
The controls o
f this system are grouped
together at the steering wheel. 1.Cruise control mode selection wheel.
2. Decrease value or speed setting on the flybutton.3.
Increase value or speed setting on the flybutton.
4. Cruise control pause / resume button.
5. Memorised speeds display button.
For more information on the list of memorisedspeeds, refer to "Memorising speeds" section).


Displays in the instrument panel

Switching off the ignition cancels any programmed speed value. Th
e cruise control is paused
manually or
by pressing the brake or clutch pedal or
on triggering of the ESP system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal until the programmed cruise speed is reached again.

172
Driving
If the cruise control is on, you can then modify
the initial speed in one of the following ways:


- using buttons 2
or 3
: )
by successive shor t presses, to modify
the speed by + or - 1 mph (km/h), )
by a long press, to modify the speed insteps of + or - 5 mph (km/h),
)Turn wheel 1to the "CRUISE"position: thecruise control mode is selected but is not
switched on (Pause).)Press button 2 or 3
: your vehicle's current
speed becomes the cruise speed (selected
on the fly).
The cruise control is activated (ON).

Modifi cation of the initial speed
setting


- pressing button 5:)the six memorised speeds are displayed
in the touch screen tablet,
)choose a value: it is displayed in the
instrument panel.
Th
e selection screen closes after a fewmoments.
The modification is then accepted.
Pause
Once switched on, you can pause the cruisecontrol at any time by pressing button 4
:
the screen confirms the pause.