2013 Citroen C4 PICASSO lock

81
2
Access

Reactivation of the interior volumetric monitoring
)Deactivate the exterior perimeter monitoring by unlocking the vehicle usingthe remote control or the Keyless Entry andStarting system.
The indicator lamp in the button goes off.
)Reactivate the full alarm system by locking
the vehicle using the remote control or the
"Keyless Entry and Star ting" system.
The indicator lamp in the button flashes once
per second again.
Tr iggering of the alarm
This is indicated by sounding of the siren and flashing of the direction indicators for
thirty seconds.
The monitoring functions remain active until
the alarm has been triggered eleven times in
succession.When the vehicle is unlocked using the remotecontrol or the Keyless Entry and Startingsystem, rapid flashing of the indicator lampin the button informs you that the alarm was
triggered during your absence. When the
ignition is switched on, this flashing stops immediately.
Failure of the remote control
To deactivate the monitoring functions:
) Unlock the vehicle using the key (integral
with the remote control) in the driver's door lock. ) Open the door; the alarm is triggered. )
Switch on the ignition; the alarm stops. The
indicator lamp in the button goes off.




Locking the vehicle without
activating the alarm
)
Lock or deadlock the vehicle using the key (integral with the remote control) in thedriver's door lock.




Operating fault


When the ignition is switched on, fixed
illumination of the indicator lamp in the button
indicates a fault in the system.
Have it checked by a CITROËN dealer or a qualified workshop.



Automatic activation *



2 minutes after the last door or the boot is closed, the system is activated automatically. )
To avoid triggering the alarm on enteringthe vehicle, first press the unlocking button on the remote control or unlock the vehicleusing the Keyless Entry and Starting system.

* Accordin
g to country.

83
2
Access
Reinitialisation of the
electric windows

Deactivating the rear controls for the rear windows

In the event of contact during operationof the windows, you must reverse themovement of the window. To do this,press the switch concerned.
When operating the passenger electricwindow switches, the driver mustensure that nothing is preventingcorrect closing of the windows.
The driver must ensure that the passengers use the electric windows correctly.
Be aware of children when operatingthe windows.
Be aware of passengers or other persons present when closing thewindows using the the electronic key or the "Keyless Entry and Starting" system.
Followin
g reconnection of the battery, the
safety anti-pinch function must be reinitialised.
The safety anti-pinch function is not active
during these operations. For the safety of your children, pressswitch 5to prevent operation of the rear windows irrespective of their positions.
The warnin
g lamp in the button comes on,
accompanied by a message confirmingactivation. It remains on, as long as the childlock is deactivated.
Use of the rear electric windows from thedriver's controls remains possible.F
or each window:
- lower the window completely, then raise it,
it will rise in steps of a few centimetres with each action. Repeat the operation until the
window closes completely,
- continue to
pull the switch for at least one second after reaching this position, windowclosed.

85
3
Comfort
Passenger's seat backrest angle
)Pull the control upwards to adjust thebackrest.
When the backrest angle is correct, release the control.
Ta b l e position for thepassenger's seat backrest


This position, associated with the position of
the rear seats, allows you to carry long objects
inside the vehicle.
When the backrest is at the correct angle, release the control lever. To ensure that thebackrest does not suddenly fold forwards and hurt you, restrain it with your back or your hand while operating the control.
Check that there is no object that could inter fere with the movement of the seat, both above and below.
)
Place the head restraint in the low position,raise the armrest and fold the fixed table onto the back of the seat.)
Pull the control fully up and tip the backrest
forwards.
To return to the normal position, guide thebackrest backwards until it locks.

94
Comfort
Flat floor
Folding a seat
From the outside) Pull firmly upwards on strap C, as indicated
by the arrow, to unlock the seat; keep
pulling until the seat is fully folded.
Push the seat backrest gently forwards so that the backrest folds onto the seat cushion. The assembly lowers onto thefloor. From the boot, when loadin
g for example You can fold the second-row seats from theboot, after first folding the third-row seats. )Pull on the strap Dto release the seat in
question then push forwards lightly on the backrest.
To avoid any damage to the mechanism,
the strap D unclips if too much force isapplied. Simply clip it in place again for thesystem to be operational again.
)Place the seats in the fully back position. Each seat can be
folded onto the floor to vary
the the space available in the boot.

95
3
Comfort

Repositioning a seat


Before operating the rear seats, check that the outer rear seat belts are notloose, to avoid damaging them. The
centre belt must be stowed. Fix the tongues of the three belts to their anchorage points.
Continuity panels
These continuity panels are not designed to support a weight greater than 30 kg.Releasin
g / locking the continuity panels) Before unfolding the continuity panels, check that the seats in the 2 ndrow are fullyback. )
Slide the continuity panel latch upwards to
release. ) Straighten the continuity panel, then slide
the latch downwards to lock it.
)If necessary, straighten the continuity panels for the seats in the 2nd row and lockthem in place.)Raise the backrest and push it rear wards
until it locks in position

Each seat has a continuity panel at the bottom
of the backrest, that once unfolded:
- provides a continuous load surface in the boot, whatever the position of the seats,
- avoids objects sliding under the seats in
the 2nd row.

96
Comfort
Access to the third row
seats
Access to the third-row seats is via the outer second-row seats.
)Pull the lever E
. The seat unlocks andthe seat cushion comes up against thebackrest. )Hold the lever E
in the raised position, pushing for wards. The whole seat slides
towards the front seat. Space becomes free behind the seat, the third-row passengers can get to their seats.





Leaving the vehicle from
the third-row seats
Repositioning a seat, from
the outside, with the door
open

In the event of a failure of this system(lever E ), the passengers in the thirdrow can also leave the vehicle after first folding the backrests of the second-row seats using the strap D. Do not allow children to operate the seats without supervision.
)
Lift the lever E. The seat unlocks andthe seat cushion comes up against the backrest.
)
Push the seat backrest, still holding the lever E
in the raised position.
If there are passen
gers seated in the third row:)manually return the assembly as far as possible rear wards; the seat does not return to the fully back position, soas to retain legroom for the third-row passengers,)fold the seat cushion until it locks.
Ensure that there is no object on or under the seat that you want to move.


Before operating the seats, ensure that the tables on the back of the first-row
seats are folded away.

97
3
Comfort











Third row seats


Concertina boards
Folding the concertina boards)
Remove the luggage net (see the "Bootfittings" section).)
Return the second-row continuity panels to
their initial position and lock them.
) Fold the concer tina boards and position
them vertically. ) Pull on the strap F
located behind the seatbackrest. The backrest pivots rear wards,pulling the seat base with it. The seat locks
in the open position.



Each of the two floor panels can suppor t a load of 100 kg.
Pull on the control, the 3 sections o
f the board will fold like a concertina.
When the third-row seats are upright, these concertina boards can be left either:
- flat behind the seats,
- in the ver tical position,
t
hereby leaving a storage area available.
Repositioning the
seats
Two rigid concertina boards, which cannot
be separated from the vehicle, cover the
2 third-row seats, when these are in the folded position.

98
Comfort
)Return the second-row continuity panels to
their initial position and lock them.
)Lower the head restraints.)Correctly position the concer tina board
ver tically behind the seat.)Check that the seat belts for the 3rd row
seats are correctly fixed to the loops andare not folded. )Pull the strap G , located at the bottom of
the seat backrest. The seat unlocks.

Before moving the third-row seats, return the rigid floor plates of the second-row seats to the upright positionand lock them.
Do not try to fold a third-row seat thathas not first had the backrest fullylocked in place.
Do not leave objects either on or underneath the seat bases of the third-row seats when you are folding them. Do not leave your hand on the control Gas you fold the seats, as you risk trapping your fingers.
Do not allow children to operate the seats without supervision.
)
Next push the backrest gently forwards.
The backrest pivots, folding onto the seat base. The seat base then folds into the stowage area provided for that purpose.) Reposition the concer tina boards over the folded seats.
Folding the seats