2013 Citroen C4 PICASSO wheel

147
4
Driving
SituationsConsequences
Displa
y of the message "Parking brake fault" and of thefollowing warning lamps: The Parking Brake is faulty, the manual and automatic functions may not operate.When stationary, to immobilise your vehicle: y


- Pull and hold the control lever for about 7 to 15 seconds, until the warning lampcomes on in the instrument panel.
If this procedure does not work, you should make your vehicle safe:


- Park on a level surface.

- Engage a gear with a manual or electronic gearbox, or place the gear selector inposition Pwith an automatic gearbox.

- If possible, fit a wheel chock.
Call on a CITROËN dealer or a qualified workshop.
Displa
y of the message "Parking brake fault" and of thefollowing warning lamps:

- The parking brake does not have its full per formance to securely hold the vehicle
in all situations.
You should make your vehicle safe:


- Park on a level surface.

- Engage a gear with a manual or electronic gearbox, or place the gear selector in
position Pwith an automatic gearbox.

- If possible, fit a wheel chock.
Call on a CITROËN dealer or a qualified workshop.
The flashin
g of the Pwarning lamps on star ting the vehicle indicates that the parkingbrake is not correctly applied.
As soon as possible, stop the vehicle and try to completely release the parking brake, using the control lever, with your foot on the brake pedal.
Displa
y of the message "Battery fault
" and the followingwarning lamp:

- The state of charge of the battery is very low and requires immobilisation of the
vehicle in a safe place: engage a gear with a manual gearbox or fit a chock toone of the wheels.

- Once the battery is completely discharged, the controls do not operate: to
release the parking brake, call on a CITROËN dealer or a qualified workshop.

150
Driving














6-speed electronic gearbox system
Six-speed electronic gearbox system which
offers a choice between the comfor t of fully automatic operation and manual gear changing. There are two driving modes:
-automatedmode for automatic control
of the gears by the gearbox, without anyaction on the par t of the driver - manualmode for sequential gear changingby the driver using the steering mountedpaddles.
In automated mode, you can temporarily take
over control of gear changing.
R
. Reverse )
With your foot on the brake, move the selector lever.N. Neutral. )
With your foot on the brake, select this
position to star t the engine.
A
. Automated mode.)
Move the selector lever to position Ato select this mode.M.Manual mode with sequential manual gear changing. )
Move the selector lever to position M
toselect this mode, then use the steeringmounted control paddles to change gear.



Gear selector lever
+.Change up paddle to the right of the steering wheel.)Pull the "+"steering mounted paddle
towards you to change up a gear.-. Change down paddle to the left of thesteering wheel.)Pull the "-"
steering mounted paddle
towards you to change down a gear.

Steering mounted control paddles


The steering mounted paddles cannotbe used to select neutral or to engageor disengage reverse gear.

154
Driving








Automatic gearbox
This gearbox offers two driving modes.
- automatedmode for automatic management of the gears by the gearbox,
without any action on the par t of the driver,-manualmode for sequential gear changingby the driver using the steering mountedpaddles.
P
.Park.


- Immobilisation of the vehicle, parking brake
applied or released.

- Starting the engine.R.
Reverse.


- Reversing, vehicle stationary and engine at
i
dle.
N.Neutral.


- Immobilisation of the vehicle, parking brake
applied.

- Startin
g the engine.D.Automatic operation. M.Manual operation with sequential changingof the six gears.


Gear selector lever


To select position P
, move the gear Pselector to the highest position (towards R), then push it for wards and Rthen to the left. Only engage it when the vehicle is at acomplete stop. In this position, the frontwheels are locked. Ensure that the gear selector is correctly positioned.

To move the gear selector, switch onthe ignition or star t the engine.
If the battery is not sufficiently charged, it is not possible to move the gear selector.


To come out of position P
, move the Pgear selector to the right to the desired position, while keeping your foot on thebrake pedal.


It is possible to change from one modeto the other at any time.
With the automated mode, you cantemporarily take control of the gear changes at any time.

155
4
Driving
+.Control paddle for changing up, to the right
of the steering wheel. )Pull the " +" paddle towards you to change
up.-. Control paddle for changing down, to the
left of the steering wheel. )Pull the "- " paddle towards you to changedown.


Steering mounted control paddles


The steering mounted control paddlescannot be used to select neutral or toselect or come out of reverse.
When
you move the gear selector, the symbol corresponding to its position is displayed in the instrument panel. P.Park. R. Reverse.
N.Neutral.D. Drive (automatic forward drive).
1 to 6.Gears engaged in manual operation.-.Invalid value in manual operation.
Displays in the instrument panel
Moving off
)
With your foot on the brake pedal, selectposition Por N.
)
Start the engine.
IfPis displayed in the instrument panel,although the gear selector is in another position, place the gear selector inposition Pto be able to star t the engine.
)
With the engine running, press the brake pedal. )
Select automated mode (position D),manual mode (position M) or reverse (position R
). R
If you do not press thebrake pedal to come out of position P, this warning lamp P


Other wise, there is an audible signalaccompanied by a message.
or symbol appears in the instrument panel, accompanied by the message"Place automatic gearbox in position P",
flashing of P
in the instrument paneland an audible signal.

168
Driving

Steering mounted controls


The information is grouped together in the
instrument panel.
6
. Speed limiter on / pause indication.
7. Speed limiter mode selection indication. 8. Speed value setting.






Speed limiter
Once the programmed speed limit is reached, additional pressure on the accelerator pedal has no effect.


The speed limiter cannot, in any circumstances,replace the need to observe speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
System which prevents the vehicle fromexceeding the speed programmed by the driver.

The controls are
grouped together at the
steering wheel.
1.Speed limiter mode selection wheel.
2. Value decrease button. 3.
Value increase button.
4.Speed limiter on / pause button.
5.List of memorised speeds display button.

Displays in the instrument panel
The speed limiter is switched onmanually:
it requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is paused
by operation of the control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply release the accelerator pedal until the vehicle returns to the programmed speed limit.
The programmed speed remains in the memory when the ignition is switched off.

F
or more information on the list of memorisedspeeds, refer to the "Memorising speeds"
section.

169
4
Driving
)Turn wheel 1 to the "LIMIT"
position: thespeed limiter mode is selected but is notswitched on (Pause).)Switch the speed limiter back on bypressing button 4
, if the speed displayed
is suitable (by default, the last speedprogrammed).)You can temporarily stop the the speed limiter by pressing button 4 again: the
display confirms that it has been stopped(Pause).

You do not have to switch the speed limiter on
in order to set the speed.Once the function is selected, you can modify
the speed setting by:
- using buttons 2
and 3
, increasing or decreasing the speed displayed: )
by successive short presses, to modifyby + or -

170
Driving
On sharp acceleration, as when descending a steep hill, the speedlimiter will not be able to prevent thevehicle from exceeding the programmedspeed.
The limiter is temporarily deactivated and the displayed programmed speed flashes. An audible signal accompanies the flashing of the programmed speed when exceeding the speed is not due to an action by the driver.
The use of mats not approved by CITROËN may interfere with theoperation of the speed limiter.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.


Flashin
g of the dashes indicates a fault with the
speed limiter.
Have it checked by a CITROËN dealer or aqualified workshop.


Operating fault
)Press firmly
on the accelerator pedal,going beyond the point of resistance,
toexceed the programmed speed limit.The speed limiter is deactivated temporarilyand the displayed programmed speed flashes.
An audible signal accompanies the flashing
of the programmed speed when exceeding
the speed is not due to an action by the driver (steep hill...).
As soon as the vehicle's speed returns to the programmed value, the limiter operates again:
the display of the programmed speed becomes steady again.
Switching off Te m p o r a r i l
y exceeding
the programmed speed
)Turn wheel 1to the "0"
position.
The display of information related to the
speed limiter disappears.

171
4
Driving
Steering mounted controls
The information is grouped together in the instrument panel.
6. Cruise control pause / resume indication.
7.Cruise control mode selection indication. 8.Speed value setting.






Cruise control

System which automatically maintains the speed of the vehicle at the value programmed by the driver, without any action on the accelerator pedal.


The cruise control system cannot, in any circumstances, replace the need to obser ve speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.
You are advised to keep your feet near the pedals at all times.
Th
e cruise control is switched on
manually: it
requires a minimum vehicle speed of 25 mph
(40 km/h) and engagement of:


- at least four th gear on a manual gearbox,

- second gear on an electronic or automatic gearbox, in manual driving mode,

- position A
on an electronic gearbox or D
on an automatic gearbox.
The controls o
f this system are grouped
together at the steering wheel. 1.Cruise control mode selection wheel.
2. Decrease value or speed setting on the flybutton.3.
Increase value or speed setting on the flybutton.
4. Cruise control pause / resume button.
5. Memorised speeds display button.
For more information on the list of memorisedspeeds, refer to "Memorising speeds" section).


Displays in the instrument panel

Switching off the ignition cancels any programmed speed value. Th
e cruise control is paused
manually or
by pressing the brake or clutch pedal or
on triggering of the ESP system for safety
reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal.
To return to the programmed speed, simply
release the accelerator pedal until the programmed cruise speed is reached again.