2013 Citroen C4 PICASSO boot

95
3
Comfort

Repositioning a seat


Before operating the rear seats, check that the outer rear seat belts are notloose, to avoid damaging them. The
centre belt must be stowed. Fix the tongues of the three belts to their anchorage points.
Continuity panels
These continuity panels are not designed to support a weight greater than 30 kg.Releasin
g / locking the continuity panels) Before unfolding the continuity panels, check that the seats in the 2 ndrow are fullyback. )
Slide the continuity panel latch upwards to
release. ) Straighten the continuity panel, then slide
the latch downwards to lock it.
)If necessary, straighten the continuity panels for the seats in the 2nd row and lockthem in place.)Raise the backrest and push it rear wards
until it locks in position

Each seat has a continuity panel at the bottom
of the backrest, that once unfolded:
- provides a continuous load surface in the boot, whatever the position of the seats,
- avoids objects sliding under the seats in
the 2nd row.

97
3
Comfort











Third row seats


Concertina boards
Folding the concertina boards)
Remove the luggage net (see the "Bootfittings" section).)
Return the second-row continuity panels to
their initial position and lock them.
) Fold the concer tina boards and position
them vertically. ) Pull on the strap F
located behind the seatbackrest. The backrest pivots rear wards,pulling the seat base with it. The seat locks
in the open position.



Each of the two floor panels can suppor t a load of 100 kg.
Pull on the control, the 3 sections o
f the board will fold like a concertina.
When the third-row seats are upright, these concertina boards can be left either:
- flat behind the seats,
- in the ver tical position,
t
hereby leaving a storage area available.
Repositioning the
seats
Two rigid concertina boards, which cannot
be separated from the vehicle, cover the
2 third-row seats, when these are in the folded position.

105
3
Comfort
In order for these systems to be fully effective, follow the operation and maintenance guidelines below: )
To obtain an even air distribution, take care not to obstruct the exterior air intake grilles
located at the base of the windscreen, the nozzles, the vents and the air outlets, as wellas the air extractor located in the boot. )
Do not cover the sunshine sensor, located on the dashboard; this is used for regulation of the digital air conditioning system. )
Operate the air conditioning system for at least 5 to 10 minutes, once or twice a monthto keep it in per fect working order. )
Ensure that the passenger compar tment filter is in good condition and have the filter elements replaced regularly. We recommend the use of a combined passenger compartment filter. Thanks to its special active additive, it contributes to the purification of the air breathed by theoccupants and the cleanliness of the passenger compartment (reduction of allergic symptoms, bad odours and greasy deposits).)
To ensure correct operation of the air conditioning system, you are also advised to haveit checked regularly as recommended in the maintenance and warranty guide. )
If the system does not produce cold air, switch it off and contact a CITRO

120
Comfort
Removable console
The removable console is a portable storage space secured to the lower centre console.
It has a sliding lid, an open storage space and two cup holders.
)Raise the locking control located at thefront of the console.)With one hand, lift the front par t of the console. )With the other hand, grasp the rear par t to release the removable console.
)
Carry out these operations in reverse order. Ensure that the console has lockedinto place.



When not fixed to its carrier, theremovable console should be stowedin the boot. It could become a projectilein the event of a sudden stop or violentimpact.

Releasing the removable
console
Refittin
g the removable
console

129
3
Comfort
Boot fi ttings
1.
Rear parcel shelf

(see details on a following page)2.Hooks
(see details on a following page)3.Torch (see details on a following page)4. Storage boxes
(see details on a following page)5. Storage net
6.Lashing eyes
7. 12 V socket (maximum power: 120 Watts)



Versions with storage boxes: theseboxes must be put in place beforeloading the boot.

130
Comfort
To remove the shelf: )unhook the two cords, )raise the shelf slightly, then remove it.
Rear parcel shelf
There are several options for storing the shelf:
- either upright behind the front seats,
- or flat at the base of the boot. The hooks can be used to secure shoppin
gbags.
Hooks
)Remove the boot carpet for access to thestorage boxes.
Storage boxes

Depending on the configuration, they are laid
out for storing:


- wheel chocks,

- a t
yre repair kit,

- two warning triangles,
-
...

131
3
Comfort
Boot fi ttings
1.
Luggage cover blind
(see details on a following page)2.Torch
(see details on a following page)3.Concertina boards 4. Lashing eyes
5. 12 V socket (maximum power: 120 Watts)
6.Arm rest with cup holder and storage space
7
. Retaining straps 8.Location for stowing the luggage cover blind 9.
Open storage

132
Comfort





Luggage cover roller
In the 5 -seat configuration, it is installed behind
the second-row seats, with the third-row seats
folded awa
y.
In the 7-seat configuration, it is stowed behind
the third row seats.
Installation
)
Position the left and right hand ends of the
roller in cut-out A
, with the mobile flap at
the front. ) Pull out the blind until it reaches the boot
pillars.
) Inser t the guides of the blind into the rails on the pillars B.

Removal
)Disengage the roller guides from the rails
in the pillars B.)Guide the blind as it is reeled in. )Unlock the roller by pressing one of
the grips located at the ends of the reelsupport.
The mobile flap allows passengers in the second row to place their seats inthe "comfort" position.