2013 Citroen C3 RHD change wheel

22
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest items in the bottom of the boot, as close as possible to the rear seats.Limit the loads carried in the vehicle and reduce wind resistance (roof bars, roof rack, bicycle carrier, trailer...). Use a roof box in preference.Remove roof bars and roof racks after use.


At the end of winter, remove snow tyres and refit your summer tyres.


Observe the recommendations on maintenance


Check the tyre pressures regularly, when cold, referring to the label in the door aperture, driver's side. Carry out this check in par ticular:



- before a long journey,

- at each change of season,

- after a long period out of use.
Don't forget the spare wheel and the tyres on any trailer or caravan.


Have your vehicle ser viced regularly (engine oil, oil filter, air filter...) andobser ve the schedule of operations recommended by the manufacturer.


When refuelling, do not continue after the third cut-off of the nozzle toavoid any over flow.


At the wheel of your new vehicle, it is only after the first 1 800 miles(3 000 kilometres) that you will see the fuel consumption settle down toa consistent average.

3
Comfort
65








Steering wheel adjustment
)
When stationary, pull the control lever to yrelease the adjustment mechanism.)
Adjust the height and reach to suit your driving position.)
Push the control lever to lock theadjustment mechanism.






Rear view mirror
Adjustable mirror providing a central rear ward
view.
Equipped with an anti-dazzle system, whichdarkens the mirror glass and reduces thenuisance to the driver caused by the sun, headlamps from other vehicles...


Adjustment
)Adjust the mirror so that the glass is
directed correctly in the "day" position.



Day / night position
)Pull the lever to change to the "night" anti-
dazzle position.
)Push the lever to change to the normal
"day" position.
Automatic day/night model
By means of a sensor, which measures the light from the rear of the vehicle, this system automatically and progressively changes
between the day and night uses.


Manual day/night model

As a safety measure, the mirrors should be adjusted to reduce the "blind spot".

In order to ensure optimum visibility during your manoeuvres, the mirror lightens automatically when reverse gear is engaged.


As a safety precaution, these
operations should only be carried out while the vehicle is stationary.

Driving
120














Electronic gearbox


R . Reverse )
With your foot on the brake, move the lever for wards to select this position.N. Neutral.)
With your foot on the brake, select this
position to star t the engine.

A
. Automated mode.)
Move the lever backwards to select this
m
ode. M + / -.
Manual mode with sequential gear changing.)
Move the lever backwards, then to the left
to select this mode, then:


- push for wards to change up a gear,

- or push backwards to change down a gear.



Gear lever

+. Paddle to the right of the steering wheel for changing up. )Press the back of the steering mounted "+"paddle to change up a gear.
-. Paddle to the left of the steering wheel for changing down.)Press the back of the steering mounted "-"paddle to change down a gear.

Steering mounted controls Five or six-speed electronically controlled gearbox which offers a choice between the comfor t of automated operation or the pleasure
of manual gear changing.
Tw o d r i v i ng modes are offered: -automatedmode for automatic control
of the gears by the gearbox, without anyaction by the driver,
- manualmode for the sequential changingof the gears by the driver, using the gear lever or the steering mounted control paddles,In automated mode, you can temporarily take control of gear changes at any time, using thesteering mounted control paddles.

The steering mounted paddles do not allow neutral to be selected, reversegear to be engaged or disengaged, or the driving mode to be changed.

Driving
132
Programming
)Turn thumb wheel 1 to the "LIMIT"position: the speed limiter mode is selected but is not switched on (PAUSE).
You do not have to switch the speed limiter
on in order to set the speed.
Exceeding the programmed speed
Pressing the accelerator pedal to exceed the programmed speed willnot have any effect unless you press the pedal firmlypast the point of resistance.The speed limiter is deactivated temporarily and the programmedspeed, which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the programmed speed.
Leaving limiter mode
)Turn thumb wheel 1
to the "0"position: the speed limiter mode is deselected. The display returns to the distance recorder.



Operating fault

In the event of a speed limiter fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a CITROËN dealer or a qualified workshop.
)Set the speed value by pressing button 2or 3(e.g.: 55 mph (90 km/h)). You can then change the programmed speed using buttons 2
and 3:- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press. )Switch the speed limiter on by pressing button 4
. )Switch the speed limiter off by pressing button 4: the display confirms that it has been switched off (PAUS E).)Switch the speed limiter back on by pressing button 4
again.

On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.

Driving
134
Programming
)Turn thumb wheel 1 to the "CRUISE"position: the cruise control modeis selected but is not switched on (PAUSE).
)Set the programmed speed byaccelerating to the required speed,
then press button 2 or 3
(e.g.: 70 mph(11 0 k m / h)).
Exceeding the programmed speed
Intentional or unintentional exceeding of the programmed speed results
in flashing of this speed in the screen.
Return to the programmed speed, by means of intentional or
unintentional deceleration of the vehicle, automatically cancels theflashing of the speed.
Leaving cruise control mode
)Turn thumb wheel 1 to the "0"position: the cruise control mode is
deselected. The display returns to the distance recorder.

)Switch off the cruise control by pressing button 4
: the screenconfirms that it has been switched off (PAUS E).
)Switch the cruise control back on by pressing button 4again.


Operating fault

In the event of a cruise control malfunction,
the speed is cleared resulting in flashing of the
dashes. Have it checked by a CITROËN dealer
or a qualified workshop.

When the cruise control is switched on, be careful if you maintain the pressure on one of the programmed speed changing buttons: this may result in a very rapid change in the speed of your vehicle. Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehiclefrom exceeding the programmed speed.
To a v o i d a ny risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.

You can then change the programmed speed using buttons
2 and 3
:
- by + or - 1 mph (km/h) = shor t press,
- by + or - 5 mph (km/h) = long press,
- in steps of + or - 5 mph (km/h) = maintained press.

11
Practical information
155
Removing a wheel

List of operations
)
Remove the bolt cover from each of the bolts using the tool 3(with alloy wheels
only).) Fit the security bolt socket 4
on thewheelbrace 1to slacken the security bolt(if your vehicle has them).)
Slacken the other bolts using the
wheelbrace 1only.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,stable and not slippery. Apply the parking brake, switch off theignition and engage first gear *
to lock the wheels. If necessary, place a chock under thewheel diagonally opposite the wheel to be changed. It is imperative that you ensure that the occupants get out of the vehicle andwait where they are safe.Never go underneath a vehicle raisedusing a jack; use an axle stand.
*
position R
for an electronic gearbox; position P
for an automatic gearbox.

Practical information
156
Place the jack 2 in contact with one of the
two front A or rear Blocations provided on
the underbody, whichever is closest to the
wheel to be changed. )Extend the jack 2 until its base plate is in contact with the ground. Ensure that thecentreline of the jack base plate is directly below the location A
or Bused.
)
Raise the vehicle until there is sufficient space between the wheel and the ground
to admit the spare (not punctured) wheeleasily. ) Remove the bolts and store them in a clean
place.
) Remove the wheel.

07
234
RADIO

By alphabetical list
Pr
ess RADIO, select the station of your choice and confi rm.

B
y automatic frequency search

Press  or 
for the automatic searchfor a lower or higher radio frequency.

Or turn the thumb wheel at the steeringmounted controls.

B
y manual frequency search
Pr
ess 
or 
to adjust the radio
frequency step by step.

SELECTING A STATION


The external environment (hill, building, tunnel, underground car park...) may interfere with the reception, including in RDS station tracking mode. Thisphenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.

The qualit
y of reception is represented by the number of
active waves in this symbol.

Pr
ess RADIO
or OK
to display the contextual menu.






CHANGING WAVEBAND

Select "Change waveband".

Select "AM / FM" and confi rm.