2013 Citroen C3 PICASSO boot

6
Fittings
103
3-panel rear parcel shelf
The front section is flexible, and the central and
rear sections are rigid.
The rear section is secured to the tailgate bytwo cords.

Removing the shelf
From the boot: )unhook the two cords, )gently lift up the shelf to unclip it,)remove the shelf.
Refi tting the shelf
From the boot: )
position the shelf so that the two notches
are directly above the fixing pins, ) press gently on the shelf to clip it in place, )
attach the two cords.


It can be stored under the ad
justable boot floor,
if this is in its high position.

Practical information
152

















Temporary puncture repair kit


Description of the kit
A.
"Sealant" or "Air" position selector.
B. On "I"
/ off "O"
switch.C.
Deflation button. D.Pressure gauge (in bar or p.s.i.). E.Compartment housing:


- a cable with adaptor for 12 V socket,

- various inflation adaptors for
accessories, such as balls, bicycle
t
yres...F
.Sealant car tridge.G. White pipe with cap for repair.
H. Black pipe for inflation.I.
Speed limit sticker.
Access to the kit
This kit is installed in the storage box, under
the boot floor.


The speed limit sticker Imust be affixed to the vehicle's steering wheel to remind you that a wheel is in temporary use.
Do not exceed a speed of 50 mph (80 km/h) when driving with a tyre repaired using this type of kit. Complete s
ystem consisting of a compressor and a sealant car tridge which permits
temporary repair of a tyre so that you can rdrive to the nearest garage.It is designed to repair most punctures which could affect the tyre, located on the tyre tread or shoulder.

11
Practical information
157














Changing a wheel

For access to them:)open the boot, )remove the boot floor, )lift up the boot carpet, )remove the box containing the tools,)remove the polystyrene storage box.


Other accessories
5.Removable towing eye.
Refer to the paragraph "Towing the vehicle".


Access to the tools

Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle.
List of tools

All of these tools are specific to your vehicle. Do not use them for other purposes.
1.Wheelbrace.
For removing the wheel trim and removing
the wheel fixing bolts. 2. Jack with integral handle.For raising the vehicle.
3. "Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels. 4. Socket for the security bolts (located in the glove box).
For adapting the wheelbrace to the special "security" bolts (if your vehicle has them).

Practical information
158

Wheel with trim
When removing the wheel
, firstdetach the trim using the wheelbrace 1pulling at the valve passage hole. When refitting the wheel
, refit the trimstarting by placing its notch facing thevalve and press around its edge withthe palm of your hand.



Access to the spare wheel
The spare wheel is installed in the boot under
the floor.
According to country, the spare wheel may be
steel or of the "space-saver" type.
For access to it, refer to the paragraph "Access
to tools" on the previous page.
Fitting the steel or "space-saver" type spare wheel

If your vehicle is fitted with alloy wheels,it is normal to notice, when tightening the bolts on fitting, that the washers donot come into contact with the steel or "space-saver" type spare wheel. Thewheel is secured by the conical contactof each bolt.

11
Practical information
159
Taking out the wheel
)Unscrew the yellow central bolt, andremove it.)Raise the spare wheel towards you from
the rear.)Take the wheel out of the boot.
Putting the wheel back in place
) Put the wheel back in its housing. )
Refit the yellow central bolt in the centre of
the wheel. ) Tighten fully until the central bolt clicks to retain the wheel correctly.
)
Put the polystyrene storage box back inplace. )
Put the box back in place and clip it.

Practical information
162

List of operations
)Put the wheel in place on the hub. )Screw in the bolts by hand as far aspossible.)Pre-tighten the security bolt (if your vehiclehas them) using the wheelbrace 1fitted
with the security socket 4 . )Pre-tighten the other bolts using the
wheelbrace 1only.

Refitting a wheel
After changing a wheel
To store the punctured wheel in the boot correctly, first remove the central cover. When using the "space-saver" typespare wheel, do not exceed 50 mph(80 km/h). Have the tightening of the bolts and thepressure of the spare wheel checked by a CITROËN dealer or a qualified workshop without delay. Have the punctured wheel repaired andreplace it on the vehicle as soon aspossible.

Practical information
170

Changing foglamp / reversing lamp bulbs
)
open the boot, )
press on the tabs using 2 screwdrivers, )
disconnect the lamp unit connector,
)
turn the bulb holder by a quar ter turn, )
remove the bulb and replace it.
To r efit, carry out these operations in reverseorder.


Changing the third brake lampbulbs (4 x W 5 W bulbs)
)
open the boot,)
remove the two plugs located on the bootinner panel,
)
press on the body of the lamp with
2 screwdrivers to remove it from itshousing, ) turn the corresponding bulb-holder a quarter turn,)
pull the bulb and replace it.
To r e f i t , c a r ry out these operations in reverseorder.


Changing the number plate lamp
bulbs (W5W)
)insert a thin screwdriver into one of the lens' exterior holes, )push it outwards to unclip.
)remove the lens. )pull the bulb and replace it.
To r efit, carry out these operations in reverse order.

Practical information
172
To r c h (Krypton 3.6V)
)Open the tab.)Push with a flat screwdriver in the holeunder the tab and recover the bulb unit. )Open the bulb unit fully to change the bulb.



Door mirror lamps (W5W)
Unclip the cover using a thin screwdriver to
access the faulty bulb.



Boot lamps (W5W)
Detach the unit by pushing it rear wards.