2013 AUDI Q5 wheel

268 Tires and wheels
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­ paved roads), the pressure monitor indi­
cator may be delayed.
-Ask your authorized Audi dealer if run­ flat tires may be used on your vehicle.
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your vehicle or accidents
could also result.
@ Tips
- The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with the "AO" or "RO" identification on the
tire sidewall¢
page 259. We recom­
mend using these tires.
Reset tire pressure monitoring system
Applies to vehicles: with tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
radio or MMI*.
11> Befo re resetting the TPMS, the current pres­
sures of all four tires must correspond to
the specified values. Adjust the tire pressure
and reset the pressure in the tire pressure
monitoring system according to the load
you are carry ing
¢page 252.
11> Turn on the ignition.
11> Select: ICARI function button > Tire pres­
sure monitoring
> Store now . Or
i,. Select: ICARI function button > Car sys­
tems *
control button > Servicing & checks >
Tire pressure monitoring > Store tire pres­
sures.
@ Tips
Do not store the tire pressure if there are
snow chains on the tire.

What do I do now?
Jack, tools and
inflatable spare tire
Onboard tool kit and vehicle jack
The vehicle tools and vehicle jack* are stored
in the luggage compartment under the floor
cover.
Fig . 209 Luggage co mpa rtment: onboard too l kit and
v e hicle jack
The vehicle jack* is sto red under the on board
tool kit¢
fig. 209.
Hybr id drive*: the storage location of the on ­
board tool kit varies
¢ page 104.
The on board tool kit includes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt covers*
- Al ignment p in for changing wheels
- Wheel bolt wrench
- Folding chocks
- Screwdriver with reversible blade
- Socket (removable Torx socket)*
- 10 x 13 open ended wrench (for disconnect-
ing the battery cables)
- Towing eye
Before storing the jack*, make sure it is
wound back down as far as it will go.
A WARNING
Imprope r use of the vehicle jack* can
cause serious personal injuries.
- Never use the j ack* supplied with your
Audi on another vehicle, particularly on a heavier one . The jack* is only suitable for
use on the vehicle it came with .
What do I d o now ? 269
-Using a bumper jack to ra ise the vehicle
will damage the bumper system. The
jack may slip, causing injury.
- Never support your vehicle on cinder
blocks, br icks or other objects. These
may not be able to support the load and
could cause injury when they fa il.
- Never start or run the engine while the
veh icle is supported by the jack* .
- If you must work under the vehicle, al­
ways use safety stands specifically de­ signed for th is purpose .
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts .
- Always make sure the inflatable spare
tire* and even a flat tire are secured in
place and not loose, otherwise they
could fly forward, causi ng personal injury
to passengers in the vehicle in an acci­
dent or sudden maneuver.
(0 Tips
Some of the on board items listed above
a re provided on certain models only or are
optiona l extras.
Folding chocks
The folding chocks are part of the on board
tool kit.
Fig . 210 Ope ning folding chocks .
To use the chocks, you first have to raise the
support plate¢
fig. 210 (D and then insert
the locking plate with the two "tabs" into the
elongated holes in the base plate@¢& . ""

2 70 What do I do now ?
& WARNING
-The ch ock cannot fulfil its function and
may lose its stab ility if t he "tabs" on the
s u pport plate are not inserted cor rectly
in to the elongat ed ho les i n th e b ase
pla te. If th is happens, the veh icle may
sta rt to move wh ile a wheel is being
change d.
- N ever u se the f old ing chocks if they are
damaged o r if th ey have no t been assem ­
bled correc tly .
Removing bass box
Appl ies to vehicles: wit h bass box
Before the inflatable spare tire" can be taken
out, the bass box mus t be removed.
Fig . 211 Spare w hee l well : Bas s box
Removing bass box
., Lift up the cargo floor using the hand le .
., Sq ueeze the locking ta bs
c:::> fig . 211 © of
the connector .
., Disconnect the connector @and place the
l ead to one side.
., Turn the large screw counter -cloc kwise .
., Carefully remove the bass box .
Installing bass box
., Carefully place the bass box in the wheel.
The inscr ipt io n "FRO NT" on the bass box
must face forward .
., Reconnect the connector that was removed .
., Secure the bass box wi th the large sc rew.
., Fold the cargo floor back down.
Inflatable spare tire
Applies to vehicles: w ith inflatable spare t ire
The inflatable spare tire expands to its full di­
ameter when it is inflated .
Fig . 2 12 In flatable spa re t ire wi th compresso r
Removing inflatable spare tire
., Lift up t he cargo floo r using the handle .
., Remove the dirt t ray .
., Tur n the large screw
c:::>fig. 212 co u nte r­
clockw ise .
., Remove the bass box as required
¢ page 270 .
., Take out the inflatable spa re tire .
., Always store the vehicle tool kit, the jack*
and the rep laced tire in the luggage com ­
pa rtment
¢ page 145.
Stow ing the inflatable spare tire
., Release the air by unscrewing the va lve
stem .
., Screw the valve stem back in afterwards .
., Wait a few hours before p lacing the wheel
in the spare wheel well¢
A-
., Inst all the bass box as required¢ page 270.
., Se cure t he wheel with t he large screw .
., Place the d irt tr ay b ack in .
., Fold t he cargo floor back down.
After using the inflatable spare wheel
T he inflatab le spare tire can be re-used as
lo ng as it is not damaged a nd is not wo rn
down to the t read wear indi ca tors ¢
_A .
When you let the a ir out of the inf latab le
spar e tir e, it does not ass ume its folded shape
again for severa l hours . U nti l then, it cannot
be pla ced ba ck in the spare whee l we ll and
stowed secu re ly.

/! WARNING
-Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators .
- If the inflatable spare tire is more than 6
years old, use it on ly in an emergency
and with extreme ca ution and carefu l
dr iv ing.
- The inflatab le spare tire is intended only
for temporary and short-term use . It
should be replaced as soon as poss ible
with the no rma l wheel and tire.
- The tire pressure value for the inflatable
spare t ire is located on the driver's side
8-p illar
c::> page 252, fig. 204.
- Maximum permiss ible speed is 50 mph
(80 km/h).
- Avoid full-throttle acce lerat ion, heavy
braking, and fast corner ing.
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for severa l hours. Until then, it
cannot be placed back in the spare wheel
well and stowed secu rely.
- Never drive with more than one inflata­
ble spare tire.
- For technical reasons, the use of tire
chains on the inf latable spare tire is not
permitted .
If it is necessary to d rive w it h
t ir e cha ins, the inflatable spare whee l
must be mo unted on the fron t axle in the
event of a fla t in a rea r tire. The new ly
available front wheel must then be in ­
sta lled in place of the rear whee l with
the flat tire. Installing t he tire chain be­
f ore mounting the whee l and tire is rec­
ommended.
- loose items in the passenger compart­
me nt can cause serious personal in jury
dur ing hard braking or in an acc ident.
Never store the inf latable spare tire o r
jack* and tools in the passenge r com­
partment .
CD Note
-The inf latable spare tire has been devel­
oped spec ifically for this vehicle model.
What do I d o now ? 271
It must not be exchanged or used for
ot her vehicle models . Sim ila rly, inflata­
ble t ires from other vehicle models must
not be used.
- Norma l summer or winte r ti res m ust not
be installed on the inf latable tire rim.
Inflating inflatable spare tire
Applies to vehicles: with inflatable spare tire
Fig. 2 13 Lu ggage compartme nt left s ide: comp ressor
.,. Remove the left tr im panel in the luggage
compa rtment.
.,. Open the Velcro strap and
remove the com­
pressor ¢
fig. 213.
.,. Unscrew the valve stem from the spare tire .
.,. Screw the tire f iller hose from the compres­
sor firmly onto the va lve of the spare tire .
.,. Insert the pl ug from the comp ressor into a
socket of th e vehicle ¢
page 75.
.,. Switch t he comp ressor on.
.,. let the compressor r un unti l t h e va lue
specif ied on the ti re press ure la bel is
reached
c::> page 2 52, fig . 204 . Switch the
compressor off after r unning for 12 minutes
at the most -danger of overheating!
A WARNING
The compressor and the tire filler hose can
become extreme ly hot while t hey a re run­
n ing -da nger of b urns!
CD Note
Switch the compressor off after running
for 12 mi nutes at the most -danger of
ove rheating! Allow the compressor to cool
down for a few m inutes befo re you use it
again .

274 What do I do no w?
Special ca re is requ ired if you are repairin g
t he t ire o n a steep incline.
@ Tips
- Do not operate the compressor for more
than 12 minutes continuously, otherwise i t can overheat. Once the compressor has
cooled, you can continue to use it.
- If sealant has spi lled out, let it dry and
then you can remove it by pee ling it away
like a fo il.
- Remember to obtain a new bottle of
sealant from your authorized Audi dealer
after repairing a tire. After this, the func­
tionality of the tire repair set is restored.
- Obey all laws.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
le ve l ground before yo u stop ¢&_ .
.,. All p assengers sho uld
le ave the c ar and
move to a safe location (for instance, behind
the guardrai l)¢
,A .
.,. Engage the parking brake to prevent your
vehicle from ro lling un intentionally¢ &_.
.,. Move
selecto r le ver to pos ition P ¢ ,A .
.,. If you are tow ing a trailer: unhitch the trail­
er from your veh icle.
.,. Block the diagonally opposite wheel with
the fo ld ing chocks or other objects.
.,. Take the
jack * and the inflatab le spare tir e*
out o f the luggage compartmen t
¢page 269.
A WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low these safety precautions:
-
- If you have a flat tire, move a safe d is­
tance off the road. Turn off the engine,
turn the emergency flashers on and use
other warning devices to a lert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly a nd possib ly slipping off the
jack*, always fully set the pa rking brake
a nd b lock the wheel d iagonally opposite
t he wheel be ing c hanged w it h t he fold­
ing chocks or other objec ts. When one
front wheel is lifted off the ground, plac ­
ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
mov ing.
- Before you change a wheel, be sure t he
ground is level and firm. If necessary,
use a sturdy board under the jack*.
- Always store the vehicle tool kit, the
jack * and the replaced tire in the luggage
compartment¢
page 145.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
1. Remove the decorative wheel cover* . For
more details see also ¢
page 2 75, Deco­
rative wheel covers
or¢ page 2 75,
Wheels with wheel bolt caps .
2. Loosen the wheel bolts ¢ page 276 .
3. Locate the prope r mounting point fo r the
jack* and align the jack * below that point
¢ page 276.
4 .
Lift the c ar with t he jack *¢ page 2 76 .
5 . Remove the
wheel with the flat tir e and
then insta ll the
inflatable spare tire*
¢ page 277 .
6. Tighten all whee l bolts lightly.
7.
Lower the vehicle with the jack*.
8. Use the wheel bolt wrench and
firmly
t ighten all wheel bolts¢ page 276.
9. Replace the decorative
whe el cover *.

/! WARNING
Always read and follow all WARNINGS and information
~ .& in Raising the vehicle on
page
277 and ~page 278.
After changing a wheel
A wheel change is not complete without the
doing the following.
• Always store the vehicle too l kit, the jack*
and the repla ced tire in t he l uggage com­
partment ~
page 145.
• As soon as possible, have the tightening
to rques
on all wheel bolts checked with a
torque wrench . The correct tightening tor­
que is 105
ft lb (140 Nm).
• Have the flat tire
re pl ac ed as soon as possi­
ble.
(D Tips
- If you notice that the wheel bolts are
corroded and difficult to t urn wh ile
changing a tir e, they should be replaced
before yo u check the tighten ing torque.
- Drive at reduced speed unt il you have the
t ightening torques checked .
Decorative wheel covers
Applies to vehicles: with decora tive wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig. 2 16 Ch anging a wheel: Removi ng the wheel cove r
Removing
• Inse rt the hook provided wi th the ve hicle
tool kit in the hole in the h ub.
What do I d o now ? 275
• Pull off the deco rative wheel co ver
~ fig. 216.
Wheels with wheel bolt caps
Applies to vehicles: with wheel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts con be un­
screwed.
Fi g. 217 Cha ngi ng a w heel : rem ovi ng the wheel bolt
caps
Removing
• Push the plast ic clip provided with the ve hi­
cle too l ki t over the wheel bo lt cap until it
engages .
• Pull on the
pla sti c clip to remove the cap
r:!) fig. 217.
Refitting
• Place the caps over the whee l bolts and
push them back o n.
T he caps are to protect and keep the whe el
bo lts clea n.

276 What do I do n ow ?
loosening and tightening the wheel
bolts
The wheel bolts must be loosened before rais­
ing the vehicle.
F ig. 218 Chang ing a wheel: loosen ing the w hee l bo lts
loosening
.. Install the wheel b olt wrench over the
whee l bolt and push it down as fa r as it wi ll
go .
.. Take tight hold of the
end of the wrench
handle and turn the wheel bolts
counter ­
clockwise
about one single turn in the direc­
t io n ofarrow ¢fig .
218 .
Tightening
.. Install the wheel bolt w rench over the
wheel bolt and push it down as far as it will
go.
.. Take tight hold of the
end of the wrench
hand le and turn each wheel bol t
clockwise
unti l it is seated.
_& WARNING
- Do no t use for ce or hu rry w hen ch angi ng
a whee l - you c an c ause the vehicle to s lip
off the jack* and ca use serious personal
injuries .
-Do no t loosen the whee l bolts more than
one turn
before you ra ise the veh icle with
the jack* . -You risk an i njur y.
(D Tips
If a wheel bo lt is very t ight, you may find i t
e asie r to loosen by ca refully push ing dow n
on t he end of the whee l bolt wrench with
one foot only . As you do so, ho ld on to the ca
r to kee p your ba lance and take care no t
to s lip.
Raising the vehicle
The vehicle must be lifted with the jack * firs t
before the wheel can be removed.
Fig . 2 1 9 Sill pane ls: mark in gs
Fi g. 22 0 Sill: pos it io nin g the jack
.. Engage the parking brake to prevent your
veh icle from rolling unintentionally
.. Move the
select or lever to po sition P.
.. Find the marking (imp rint) on the sill tha t
is nearest t he wheel that w ill be changed
r:::;, fig . 219. Be hind the mar kin g, there is a
lifting point on the sill for the jack *.
.. Turn t he
jack* located under the lifting
point on the sill to ra ise the jack until its
arm @
r:::;, fig. 220 is located under the des­
ig nated p lastic mount
r:::;, ,& ¢ 0.
.. Align the jac k* so t hat its arm @ r:::;, fig. 220
engage s in the desig nated lifting poin t in
t he doo r sill and the movable base ® lies
flat on the ground. The base ® must be
ver­
tical
un der the lifting point @.
.. Win d the jack * up further until the flat tire
comes off the ground
Q ,& .
Position the jack* only under the designated
li fting points on the s ill
r:::;,fig. 219. There is Ill-

exactly one location for each whee l. The jack*
must not be positioned at any other location
¢ &. ¢ (D .
An unsta bl e s urface under the ja ck* can cause
the vehicle to slip off the jack* . Always provide
a firm base for the jack* on the ground. If nec­
essary place a sturdy board or s imilar support
under the jack*. On
ha rd , sli ppery surfaces
(such as tiles) use a rubber mat or simi lar to
prevent the jack* from slipp ing
<=> &. .
A WARNING
- Yo u or your passengers could be injured
wh ile chang ing a whee l if you do not fol­
low these safety precautions:
- Position the jack * only at the designat­
ed lift ing points and align the jack*.
Otherwise, the jack* could slip and
cause an injury if it does not have suff i­
cient hold on the vehicle.
- A soft or unstable surface under the
jack* may cause the vehicle to slip off the jack*. Always provide a firm base
for the jack* on the ground . If necessa­
ry, use a sturdy board under the jack*.
- On ha rd, slippe ry surface (such as tiles)
use a rubber mat o r similar to prevent
the jack* from slippi ng.
- T o he lp p revent injury to yourself and
yo ur passengers:
- Do not raise the vehicle unti l you are
sure the jack* is securely engaged.
- Passengers must not remain in the ve­
h icle when it is jac ked up .
- Make s ure t hat passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then contin ue to
ra ise the jack *.
(D Note
Do not lift the vehicle by the s ill. Pos ition
the jack * on ly at the des ignated lifting
points o n the sil l. Otherwise, your vehicle
will be damaged.
What do I d o now ? 277
Taking the wheel off/installing the
inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
Fig . 2 21 Changing a whee l: using the screwdriver han­
dle (w it h the blade removed) to turn the bolts
Fig. 222 Cha ngi ng a wheel: align ment p in inside the
top hole
After yo u have loosened all wheel bo lts and
raised the vehicle off the ground, remove and
replace the wheel as follows :
Removing the wheel
... Use the hexag onal so cket in the screwdri v­
er handle
to completely remove the top­
most whee l bolt and set it aside on a
clean
surface ¢ fig. 221.
... Screw the threaded end of the alignm ent
p in from the tool kit hand-tight into the
empty bolt hole
<=> fig. 222.
... Then remove the other wheel bolts as de­
scribed above.
... Take off the wheel leaving the a lignment
pin in the bolt hole
¢ (D .
Putting o n the inflat able sp are t ire*
... Inflate the inflatable spare tire*
<=> page 2 71 and push the wheel over the
alignment pin .