2013 AUDI Q5 garage door opener

Homelink®
Universal remote
control
Description
Applies to vehicles: with Home link
The HomeLink universal remote control con
be programmed with the remo te control for
devices that ore already present.
With Home Link, you can control devices such
as the garage door, secu rity systems, ho use
lights , etc. comfortably from the inside of you
veh icle .
H omelink makes it poss ible for you to rep lace
t hree different remote controls from dev ices
in your home with one un ive rsal remo te. Th is
featu re works for most garage door and exte­
rior door motor signals. Programming the in­
d ividual remote control for your remote con ­
trol takes p lace near the center of the radiator
grille. There is a control module attached at
this location .
A one-t ime programm ing of the sensor must
be performed before you are able to use sys­
tems with Homelink. If the system does not activate after performing the one-t ime pro­
gramming, check whether the system uses a rolling code ¢
page 138 for vehicles without
the MMI*.
& WARNING
-
- Never use the Homelink ® transmi tter
with any garage door opener that does have not the sa fety stop and reverse fea ­
ture as requ ired by federa l safety stand­
ards. Th is includes any garage door open­
er mode l manufactured before April 1,
1982.
- A garage door opener which cannot de­
tect an object, signaling the door to stop
and reverse does not meet current feder­
al safety standards . Us ing
a garage door
opener without these features increases
r isk of serious inj ury or death.
Homelink ® 135
-For safety reasons never re lease the
parking brake or start the eng ine while
anyone is standing in front of the vehicle .
- A garage door or an estate gate may
sometimes be set in motion when the
Homelink ® remote control is being pro­
grammed. If the device is repeatedly ac­
tivated, th is can overstrain motor and
damage its e lectrical compon ents -an
overheated mo to r i s
a fire hazard!
- To avo id possib le injuries or property
damage, please always make abso lutely
certa in that no person s or objects are lo­
cated in the range of motion of any
equ ipment being operated .
(0 Tips
-If you would like more information on
Homelink ®, where to purchase the
Home link ® compatib le products, or
would like to purchase the Homelink ®
Home Lighting Package, please ca ll toll­
free: l-800-355-3515.
- For Declaration of Compliance to United
States FCC and Industry Canada reg ula­
tions
¢ page 298.
- For security reasons, we recommend that
you clear the programmed b uttons be­
fore selling the veh icle.
Operation
App lies to vehicles : with Homeli nk
Fig . 14 9 Head li ner: controls
Req uirement : The buttons must be program-
med
<:!)page 136 or ¢page 137. ..,_

136 Homelink®
• To open the garage door, press the p ro­
grammed button . The LED @will light up or
flash.
• To close the garage door, press the button
again.
@ Tips
To open the garage door, press the button, but do not press it for longer ten seconds
or the Homelink module w ill switch to
programming mode.
Programming the transmitter (version A)
Appl ies to vehicles: with Home link
Fig. 15 0 Distance between t he rad iator grille and th e
hand transmitter
You can p rogram the fixed code and ro lling
code systems using the descr ibed procedure.
Programming the button
• Turn the ig nition on .
• The re a re two ways to program the but ton:
P res s the but ton¢
page 135, fig. 149 tha t
yo u wou ld like to p rogram . Use the instruc­
t ions tha t appear in the MM I* to perform
the p rogramming. Or
• Se lect:
ICARI function button > Car sys·
terns *
control button > Vehicle settings >
Garage door opener > Program gar age door
opener .
• Select the button that yo u would like to
program.
• Fol low the ins truc tions in the MMI*.
• If the gar age door openi ng mus t also be
syn chronized wit h the Homel ink mod ule,
refer to t he owner's manual for t he garage
door opener. R
emote cont ro l units fo r garage door opene rs
in Canada are set to stop transmitting radio
frequency signa ls after two seconds . This t ime
may not be suffic ient for the Home link sys­
tem to learn the radio frequency signal. Per·
form all other steps as described above .
Erasing/Clearing the programmed button
settings
• To e rase all of t he programmed buttons at
the same t ime, select:
I CAR I function button
> Car systems * control button > Vehicle set·
ting s
> Garage doo r open er > Clear pro·
gram setting s> Yes.
The prog rammed b ut­
t ons can no t be erased individua lly. Re pro­
gram the butt ons if necessa ry .
• Reprogram an individua l bu tton in the same
manner that you wou ld for the one-time
programm ing .
Displaying the version /status/country
code
• Select: I CAR ! function b utton > Car sys·
terns *
contro l button > Vehicle settings >
Garage door opener > Version information .
(D Tips
-Programming using the M MI* is not
available for all ve hicle vers ions.
- The required distance betwee n the hand
transm itter and the Homelink module in
the radiator gr ille ¢
fig. 1 SO depends on
the system that you are prog ramm ing .
- Depending on the mode l of the ga rage
door opener, you may need to release the
butto n on the remote and press it again
w hen programming. When program·
m ing a new device, keep the butto n
presse d for at least 15 s econds before
t ry ing ag ain w ith the tra nsmit ter in a dif­
fere nt posi tion.

Programming the transmitter (version B)
Applies to vehicles: with Horne link
Fig. 15 1 Distance between the radiator gr ille and the
hand transmitter
P rogrammin g: ph ase 1 on the control unit
1. Sw itch on the ig nit ion (do no t start the
engine) .
2. Press and hold both of the outer Home­
Link buttons
r=>page 135, fig. 149 until
the LED @ turns off completely (about
20
seconds). Th is procedure clears the stand­
ard codes that were set at the factory and
does
n ot need to be repeated agai n to
p rog ram the other buttons.
3. Briefly press the Homelink button that
you would li ke to prog ram .
4 . Wai t unti l the LED @ beg ins to b link
q ui ckly. The Home Link modu le wi ll now
remai n in learning mode for
5 minutes .
5. Now stand in front of your vehicle with
the original hand transmitter for the ga­ rage door opener or for the device that
you would like to allocate to the Home­
Link button.
Programming: pha se 2 on th e radiator
grille
6 . Hold the orig inal hand transmitter some­
what towa rds the center of your vehicle 's
radiato r grille r=>
fig. 151.
7. Now act ivate (p ress) t he hand transmit­
ter.
8 . Pay a ttention to the tu rn signals for you r
vehicle when activating the ha nd trans­
mitter . If t he emergency flashers blink
three times, the programming was suc­
cessful. If the emergency flasher only
bli nks one t ime, the 5 minute t ime limit
Homelink ® 13 7
for the adaptation has expired or the pro ­
gram ming was unsuccessful. Repeat the
programming from step 3 on the controls
or select another distance from the radia­
tor grille.
9. If the garage door or other devices sti ll
fail to be activated w it h the Homelink
control buttons after p rogramming is
comple ted, it is possib le tha t these sys­
tems might be working with a rolling code
ins tead of the normal fixed code .
A Roll­
ing code programming must be per ­
formed
r=> page 138 .
Program the rema ining two buttons a ccord ing
to the instructions mentioned above . Beg in
similar ly w ith the 3rd step if the program ­
ming connection was successful for t he first
button.
Remote con tro l units fo r garage door opene rs
in Canada are set to stop transmitting radio
frequency signa ls after two seconds . This time
may not be suffic ient for the Homelink sys­
tem to learn the radio frequency signa l. Per­
form all other steps as described above.
Erasing the buttons
.,. Switch o n the ignition (do not start the en­
gi ne).
.,. Press and hold both of the outer buttons
until the LED @ turns off completely (about
20 seconds) to erase all of the buttons si­
m ultaneously .
.,. Programmed buttons cannot be erased ind i­
vidua lly. Reprogram the buttons if necessa­
ry .
Reprogramming the buttons
.,. Switch on the ignition (do not start the en­
gine) .
.,. To reprogram an individua l butto n, press
and hold the button unt il the LE D @ starts
to f lash quickly (after abo ut ten seconds) .
Release t he but ton imme dia tely. The Home­
L ink module will now remain in learning
mo de for 5 minutes.
.,. Continue with step 5.

138 Homelink®
-The required dista nce between the hand
transmitter and the HomeLink module in
the radiator grille
c:> fig. 151 depends on
the system that you are programming.
- Depend ing on the model of the garage
door opener, you may need to release the
button on the remote and press it again
when programming . When p rogram­
ming a new dev ice, keep the button
pressed for a t least 15 seconds befo re
trying again wi th the transmitte r in a dif­
ferent pos it ion. W atch out fo r the emer­
gency flasher during that time .
Programming the rolling code
Applies to vehicles: with Home link
Additionally, a rolling code programming for
the HomeLink universal remote control is re­
quired for some systems .
Identifying the rolling code
.. Press the prev ious ly programmed Homelink
button aga in and hold i t down .
.. Look at the LED@ c:>
page 135, fig. 149 . If
the LED blinks quickly , the features, s uch as
the garage door o pener, are equipped with
the rolling code .
.. Program the roll ing code as fo llows:
Act ivating the garage door opener motor
unit
.. Locate the sett ing button on the garage
door opener motor unit . The exact location
and co lor of the b utton may vary depending
on the garage door opener ma nufacturer .
.. Press the sett ing button on the garage door
opener motor unit (usually th is w ill act ivate
a "se tt ing light d isp lay" on the moto r unit).
Now you w ill have abo ut
30 se conds ti me to
p erfo rm the Home Link bu tton programming
on the cont ro ls.
Programming on the controls
.. Press the Home L ink button that was already
programmed and hold for two seconds . ..
To end ro lling code programm ing, p ress and
hold t he Home link button for two seconds
aga in .
.. The Homelink button may need to be press­
ed a t hird t ime to end the adjus tment proce­
dure for some garage door openers .
After the controls have been programmed, the
garage door opener s hou ld recogni ze the
Homelink signa l and operate when the Home­
Li nk button is pressed . N ow you may program
the o ther buttons as needed .
(D Tips
-Programmi ng the rolling code can be
performed quicke r and more easily with
the help of a second person .
- If d iff iculties should ar ise when pro­
gramming the rolling code, consult the
op erating instructions fo r th e garage
door opener or o ther dev ices for po ssible
s o lu tions.